How to fill gaps in old wood floor

  Рет қаралды 66,148

Refinishing hardwood floors : Ermes12

Refinishing hardwood floors : Ermes12

Күн бұрын

Пікірлер
@amandar5827
@amandar5827 Жыл бұрын
Looks awesome!!! Do you sand again after the filler dries? And does it take stain well? I always envision these lighter spots where the filler goes!
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
the filler is done in two steps the first hand is done after you do the sanding with belt 36 if the floor is oak and instead if it is pine with belt 24 then the second is done before you do the final hand with belt 100
@amandar5827
@amandar5827 Жыл бұрын
@@Ermes12FloorSander Thank you! They are old growth oak, very tight grains. So I'm going to do 2 sets of fillers? And at any point do I stain the filler?
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
but you have to pour the juice slowly until it remains soft
@kcjean827
@kcjean827 Жыл бұрын
Gorgeous floors and craftsmanship. Im fixing to refinish the floors in a few weeks so I'm trying to learn as many tips and tricks as i can before then to make the process as smooth as possible 🥰
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
yes, then realize that to start you need for the orbital eger you need disk 36 - for the first process for the second process disk 50. and for the final process disk 80 with Festool. this is valid for the corner this only for eger with disc 36 and 50 instead disc 80 is used for the final hand on the corners with Festool. instead for the hummel you will need a 36 belt for the first coat then a 50 belt for the second coat. and for the last procedure belt 100 . 👷‍♂️
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
if, however, your floor is made of pine you will have to do the first processing not with disc 36 but with disc 24 with eger. even with hummel 24 tape only for the first procedure.
@stankozak4821
@stankozak4821 2 ай бұрын
liquid
@Ermes12FloorSander
@Ermes12FloorSander 2 ай бұрын
is called Jenkins joint wood filler liquid
@kcjean827
@kcjean827 2 ай бұрын
@@Ermes12FloorSander thank you 🙏💕
@leumnanthavong
@leumnanthavong 2 жыл бұрын
Good content Pease keep on thanks for sharing video
@chatra_fingerstyle
@chatra_fingerstyle 2 жыл бұрын
Thanks for sharing video
@FaithRichFidler
@FaithRichFidler Жыл бұрын
I've not been able to find the liquid you poured into the sawdust. I'm restoring a 1905 rock-faced block home, which was oak floors. I've done the floor sander from 24grit to 100grit. I am to the point of needing to purchase the filler, but can't seem to locate what people are actually using. Could you give me the same of what you're using? I know you have "Jenkins" listed, but when I Google that, it doesn't NOT come up with what you're using.
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
you should look for it like this 👇 Jenkins Joint Filler Cellulose Based 1L
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
you can search on google for the liquid you need to make the filer on your floor
@FaithRichFidler
@FaithRichFidler Жыл бұрын
@@Ermes12FloorSander I've been looking, I found Minwax Sanding Sealer .... and I'm hoping it's close enough.
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
I think so and best wishes for your project 👍👍
@LuisMartinez-js5fb
@LuisMartinez-js5fb Жыл бұрын
@@FaithRichFidlerdid the MinWax sanding sealer work mixed with the wood dust ? I’m planning to use it since I didn’t find the Jenkins product . Please let me know
@michaelvachon1334
@michaelvachon1334 9 ай бұрын
What is the fluid you used to mix with the sawdust? Looking for something that would be available in the US that is similar to the Jenkins wood filler you noted. Is this just a liquid epoxy?
@Ermes12FloorSander
@Ermes12FloorSander 9 ай бұрын
Hi .there is Bona mix and fill also Lecol wood filler wichbis similar to jenkins . I am not sure if you can get them in America but i should think so . You can also use pva wood glue to mix with saw dust for small gaps but its not very good for wide ones . Thank you for coment and viewing my channel.
@krystleporter3778
@krystleporter3778 5 ай бұрын
@@Ermes12FloorSander When you say PVA isn’t good for large cracks, can you still use it on 2-3mm cracks?
@Ermes12FloorSander
@Ermes12FloorSander 5 ай бұрын
@krystleporter3778 yes you can use it in 2-4 millimiter gaps .
@jamesknight2416
@jamesknight2416 11 ай бұрын
What do I mix with the saw dust to make the mixture to fill the floor gaps??
@Ermes12FloorSander
@Ermes12FloorSander 11 ай бұрын
the liquid filler that I use is called Jenkins joint filler.
@jamesknight2416
@jamesknight2416 11 ай бұрын
Is there a equivalent in the United States
@Ermes12FloorSander
@Ermes12FloorSander 11 ай бұрын
I don't know if the product exists there in United States. but you would want to use a product similar to what you find in your country. (I'm in Europe)
@q8463
@q8463 2 ай бұрын
So how long does the filler last? I can see it cracking and coming out fairly quickly
@Ermes12FloorSander
@Ermes12FloorSander 2 ай бұрын
It depends on the floor ,if its pine floor and there is movement it will crack really quick ,also when the floors shrink and expand will crack ,at most will last couple of years in optimal conditions .
@dang6832
@dang6832 3 ай бұрын
I have now watched a video. I feel like I could do it without help……and I’m sure I’d let myself down. That herringbone looks great.
@jamesknight2416
@jamesknight2416 Жыл бұрын
Any one else notice to door open by itself after he shut it???
@mona-lisa7484
@mona-lisa7484 10 ай бұрын
The windows are opened throughout the house and the air is blowing
@c4r5on88
@c4r5on88 8 ай бұрын
I have a door that does this all the time and it pees me off
@Nninjarider
@Nninjarider 5 ай бұрын
Yes
@brandonmehrabi268
@brandonmehrabi268 3 ай бұрын
It's a ghost
@phillipdukes8319
@phillipdukes8319 7 ай бұрын
This is cool! When sealing the gaps, is there any concern for expansion/contraction of the wood?
@Ermes12FloorSander
@Ermes12FloorSander 7 ай бұрын
Yes when doing soft wood it will fall and come out eventually while hard woods last longer.
@Yeshua73732
@Yeshua73732 4 ай бұрын
After filling with the dust did you just apply the sealer straight on or did you give it a light sand again then sealer?
@Ermes12FloorSander
@Ermes12FloorSander 4 ай бұрын
After filler you sand it again then you apply sealer .
@Yeshua73732
@Yeshua73732 4 ай бұрын
@@Ermes12FloorSander what sand pads should i use for the first sanding and what pads should i use for the sanding before sealer? Im thinking a heavier sand pad before and after really light one before sealer? Would this be correct the way? Cheers
@Ermes12FloorSander
@Ermes12FloorSander 4 ай бұрын
so I use these crazy ones for the first procedure I use belt 36 for the first. second I use belt 50. and for the final process I use belt 100. also for the edges I use first process with disc 36. for the second disc 50. and for the last hand I use disc 80 for the edges.
@Ermes12FloorSander
@Ermes12FloorSander 4 ай бұрын
you do the filler after you do the first procedure. for example you start to woo the floor with belt 36. also the edges with edger disc 36 when you do this. after you apply the filler. and then you wait 30 minutes or more for the filler to dry. and proceed with belt 50. then belt 100 final. done this. after you do the edges with edger disc 50 and to finish the edges do Festool disc 80
@faith9017
@faith9017 4 ай бұрын
Looks awesome! What clear coat did you use on top?
@Ermes12FloorSander
@Ermes12FloorSander 4 ай бұрын
it's called bona varnish matt
@sergyag
@sergyag 4 ай бұрын
Great video! What materials do you use to make the wood filler? And how do you achieve desired color? Thanks
@Ermes12FloorSander
@Ermes12FloorSander 4 ай бұрын
Jenkins joint filler but any ressin will do and if you use the saw dust from the acctual floor will be the closest match as it is dust from the same wood .
@jakeb1778
@jakeb1778 3 ай бұрын
​@@Ermes12FloorSander Do you sand the floor again after applying filler? What's the final stain/topcoat used? Does the filler take stain?
@Ermes12FloorSander
@Ermes12FloorSander 3 ай бұрын
@jakeb1778 then the filler is used before the final sanding with belt 100. I use the filler. and after that I leave it for an hour for the filler to harden. then I use the last procedure to sand the floor with belt 100. and for the edges I use the last coat disc number 80. then after doing this. apply the stain on old wood floors. the name of the stain is morrells light teak stain. for the color. after this you let the stain dry. I put 3 coats of matt varnish.
@gianlucatoscano1607
@gianlucatoscano1607 9 ай бұрын
Hi there, Just a question, can I use a hand sander for a project similar to this one? If yes, what grind size you suggest to use at the beginning till the end? I guess the best os to start with the tough one and then gradually move to the finest one isn't it? Thanks 😊
@Ermes12FloorSander
@Ermes12FloorSander 9 ай бұрын
Hi .yes you could use a hand sander .(orbital or belt ) you shuld start with a 36 grid paper then 50 then a final 100 .il will not be as easy as if you use the havy machine sander but definitively can be done .
@gianlucatoscano1607
@gianlucatoscano1607 9 ай бұрын
Thanks for the reply mate, another quick question. For how long does the saw dust mixed with the joint filler needs to dry? After the drying process did you sand it again? If yes what grit you suggest. I guess after all of that you stain the floor and than apply a primer maybe? After the primer you can apply the varnish isn't it? Thanks again for your replies 😊
@Ermes12FloorSander
@Ermes12FloorSander 9 ай бұрын
and dry the file for 30 minutes. maybe the filer proceeded with 100 reps. base repeats 100 if you are not pine wood. Make a 150 disc bather. And if the floor is pine, there is no need for a bather. after we make these special arrangements. and after the stain dries, we apply varnish. thanks for the comment.👷‍♂️
@Ermes12FloorSander
@Ermes12FloorSander 9 ай бұрын
even after we have given the first coat of varnish after it has dried well. if the floor is pine, we give it a hand sand with paper 120. if it is an oak floor, we must give it 2 hands of varnish after making a buffer disc 150. do not sand the floor, it will take 3 coats of varnish.
@Ermes12FloorSander
@Ermes12FloorSander 9 ай бұрын
Sei italiano?
@sighck
@sighck 6 ай бұрын
Is there a similar method and product for outdoor decks?
@Ermes12FloorSander
@Ermes12FloorSander 6 ай бұрын
You can do the same thing for decking go through the same proces bit no need for filler and you use decking oil as a finish .
@eltiburon9546
@eltiburon9546 22 күн бұрын
What kind of solution did you mix it with ?
@Ermes12FloorSander
@Ermes12FloorSander 21 күн бұрын
the name of the product is called Jenkins joint filler ,you can also lecol or bonna.
@eldonhoward7925
@eldonhoward7925 5 ай бұрын
The floors look great!
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
Floors are suppose too expand and contract?? Is this too save money on polyurethane??
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
this filler thing i always recommend its a short lived thing not long lived and the filler will fall off. people who choose it can't stand open spaces even if the duration is short
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
But doing that your going too ruin alot of floors
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
my job is floor seder.
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
I don't know what your job is but as I wish you first, I wish you the best of luck in your job.✌️😁👷‍♂️ and I hope not to ruin them but to give them their splendor again.😁✌️👋👷‍♂️
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
Try fractal burning a hardwood floor
@mattchapman8477
@mattchapman8477 Жыл бұрын
Do you sand again after you put the wood filler down, then stain?
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
yes after the filler you have to send the floor again
@mattchapman8477
@mattchapman8477 Жыл бұрын
@@Ermes12FloorSander Thank you. Do dark stains penetrate the wood filler? Have you ever mixed stain into the wood filller?
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
@@mattchapman8477 you let the filler dry for a few hours then sand it flat with the floor then you apply the stain .the stain take to filler aswell when you stain the floor .
@SpiritTracker7
@SpiritTracker7 10 ай бұрын
Is this a good idea for every zone in the US? I mean where temperatures that fluctuate from 10 degrees in the winter to 95 degrees in the summer, with the contracting and expanding isn't that why we see failed gap filler cracking up which then becomes impossible to refinish again without digging that all out?
@Ermes12FloorSander
@Ermes12FloorSander 10 ай бұрын
hi ,in areas where the weather fluctuate a lot its probably a good idea not to fill as it will eventualy crack and fall ..
@Ermes12FloorSander
@Ermes12FloorSander 10 ай бұрын
when I proceed to fill the empty spaces in the floor I always explain that it is something that does not last over time, the filler falls off over time and because of the movement of the wooden boards that move or widen over time
@robertedwardleesmyth7669
@robertedwardleesmyth7669 10 ай бұрын
Would help to know the products you are using
@robertedwardleesmyth7669
@robertedwardleesmyth7669 10 ай бұрын
Sorry found it in your comments
@Ermes12FloorSander
@Ermes12FloorSander 10 ай бұрын
the color applied is called light oak stain. and instead the product to fill the spaces on the floor is called Jenkins joint filler
@Ermes12FloorSander
@Ermes12FloorSander 10 ай бұрын
thanks for your comment .👷‍♂️
@jessicabereznyckyj1428
@jessicabereznyckyj1428 6 ай бұрын
What did you use to get the gloss finish?
@Ermes12FloorSander
@Ermes12FloorSander 6 ай бұрын
It was a Bonna satin varnish .
@Bayyourday
@Bayyourday 2 ай бұрын
What two chemicals did you pour onto the sawdust?
@Ermes12FloorSander
@Ermes12FloorSander 2 ай бұрын
It's called Jenkins Joint Filler
@Nninjarider
@Nninjarider 5 ай бұрын
What color is it after the filling? I don't want this dark brown color.
@Ermes12FloorSander
@Ermes12FloorSander 5 ай бұрын
The filler is done by mixing the dust from the floor that you sand with resin so it varies fron floor to floor depending on the colour of the wood ,but is the closest match to the color of the wood as it is the actual dust from it .
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
Is that the dirty sawdust you got from the floor sander??
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
yes
@mitchellmayerchak163
@mitchellmayerchak163 11 ай бұрын
Can you still stain the floor after doing this
@Ermes12FloorSander
@Ermes12FloorSander 11 ай бұрын
after we fill the spaces on the floor with filler we have to do again sanding the floor and after you can stain
@paulmryglod4802
@paulmryglod4802 11 ай бұрын
Nicely done. Good editing
@Ermes12FloorSander
@Ermes12FloorSander 11 ай бұрын
Thanks!
@jakejacobson2999
@jakejacobson2999 10 ай бұрын
What product did you use?
@Ermes12FloorSander
@Ermes12FloorSander 10 ай бұрын
il nome del prodotto si chiama Jenkins joint filler
@CriaAndKiddFW
@CriaAndKiddFW Жыл бұрын
You left the edges unsanded?
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
I have done the edges ,you can see on my other videos how is done ,this video was to show the filling process and the finish .
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
in the corners and 2 procedures were done with Edger disc 36 and 50 and last process was done with Festool disc 80. thanks for your comment.👷‍♂️
@TheFatherTheSonHolySpirit
@TheFatherTheSonHolySpirit 7 ай бұрын
Whats was the dark color at the end you painted the whole floor
@Ermes12FloorSander
@Ermes12FloorSander 7 ай бұрын
the name of the color is called jacobean dark oak stain
@Ermes12FloorSander
@Ermes12FloorSander 7 ай бұрын
But it must be mixed with white spirit. for example a glass of akua filled with jacobean dark oak stain and two glasses of water filled exactly as done with white spirit stain. and you will have that color. 👍👷‍♂️
@TheFatherTheSonHolySpirit
@TheFatherTheSonHolySpirit 7 ай бұрын
Thank you
@TheFatherTheSonHolySpirit
@TheFatherTheSonHolySpirit 7 ай бұрын
@@Ermes12FloorSander does the white spirit cause the color to be a little later than jacobean oak brown alone
@TheFatherTheSonHolySpirit
@TheFatherTheSonHolySpirit 7 ай бұрын
What is white spirit and akua are these paint thinner ?
@nickorango
@nickorango Жыл бұрын
Can this be done in four season house?
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
Yes no problem you can do it
@nickorango
@nickorango Жыл бұрын
@@Ermes12FloorSander Great. I will try it.
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
👷‍♂️👍
@267BISMARK
@267BISMARK 2 жыл бұрын
Do you have to sand the floor again thanks?
@Ermes12FloorSander
@Ermes12FloorSander 2 жыл бұрын
Hi ,yes you have to sand after the filler then laquer it
@267BISMARK
@267BISMARK 2 жыл бұрын
@@Ermes12FloorSander thank you
@08manuelelias08
@08manuelelias08 2 жыл бұрын
could not see the name of the glue
@Ermes12FloorSander
@Ermes12FloorSander 2 жыл бұрын
the product name is, jenkins joint filler
@colemeeker908
@colemeeker908 Жыл бұрын
Will the Jenkins wood filler work for large chunks or divots in the floor?
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
yes it works but first you have to put something on the spaces, for example tape on the spaces. stand a little bit close to the floor and then do the filer on the floor. wait for the filer to dry. sand the floor. and then do the second coat. before performing the last finishing process
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
in the first coat the filer should be not very liquid. but a little creamy so it sticks better on the sides of the floor it doesn't fall down. and on the second coat, more liquid from the first coat than in the first coat, so it will be better. hope i helped.👍👷‍♂️
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
and thanks for your comment
@loxhaerme8730
@loxhaerme8730 Жыл бұрын
Well done good job 👍
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
Show me those same floors after 1 month
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
what tattiche are you talking about.?
@A5cension
@A5cension Жыл бұрын
If I didn't live in a four season climate I would have done this to my floors.
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
thanks for your comment. 👍😁
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
I want too do my Future Kitchen Floor in pennies after all it is .99 a sq.Foot and Germs and Bacteria do not survive on Copper🥳
@jakejacobson2999
@jakejacobson2999 10 ай бұрын
@@MayhemMcLickinz-bq5zrterrible idea lol unless you don’t plan on selling your house
@EriVini-w8z
@EriVini-w8z Жыл бұрын
Bene fatto complimenti bell video 👍👍👍
@sacajuncaj-berishaj547
@sacajuncaj-berishaj547 2 жыл бұрын
What is name or brand of wood glue? Thanks
@Ermes12FloorSander
@Ermes12FloorSander 2 жыл бұрын
the product name is, jenkins joint filler
@user-TheBlackSheep
@user-TheBlackSheep Ай бұрын
This would only help very fine gaps. There are no gaps in the floor it even looks like laminate, I have 1904 boards with massive gaps that amount of sandy crap would make a right mess and would proberbly turn dusty and come up with the hoovering. Caulking sealant and wood filler putty are my go to none of this mixing stuff myself, I do use a bit of sawdust out of my sander in big holes to help me use less filler though.
@Ermes12FloorSander
@Ermes12FloorSander Ай бұрын
I agree with you ,that caoulking is better last longer but most people wont pay for it as it will be pricy but if you do it youself its cheaper .
@TheParaparGroup
@TheParaparGroup 11 ай бұрын
very good!! Thank you!
@Ermes12FloorSander
@Ermes12FloorSander 11 ай бұрын
Thank you too!
@t.1erme747
@t.1erme747 2 жыл бұрын
Perfect 👍👍👍
@emmamcdonagh7189
@emmamcdonagh7189 Жыл бұрын
looks amazing 🙂how long after filling and staining do you have to wait before applying the laquer? thank you
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
after you put file, wait 20 minutes before sending it again with belt 100, after you have done this, paint the floor with stain and wait until it dries well. then apply the first coat of varnish duet and sand the floor with sandpaper 120 - 150 if it is pine or on the oak floor use bather orbital sander with disc 120 and finally give it 2 more coats of varnish
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
thanks for your comment
@emmamcdonagh7189
@emmamcdonagh7189 Жыл бұрын
Thanks so much! That’s really helpful :)
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
I'm glad I helped 👷‍♂️
@lutomyrto5342
@lutomyrto5342 Жыл бұрын
Wow looks amazing keep it up bro 💯💥
@rencross7399
@rencross7399 7 ай бұрын
Paranormal activity @ 3:12 👻
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
How much are homeowners paying for this??
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
Now I'm living in Central PA
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
I don't know I'm an employee I don't know the costs sorry
@MayhemMcLickinz-bq5zr
@MayhemMcLickinz-bq5zr Жыл бұрын
I hope your getting at least 30.00 an hour
@sentientthundertank2079
@sentientthundertank2079 2 ай бұрын
I have watched 100, 000, 000 of these videos and still don't know what the liquid is
@Ermes12FloorSander
@Ermes12FloorSander 2 ай бұрын
the liquid they show you in the video is called jenkins joint filler, it is a product. which is mixed with the wooden dust to filing the gaps to the floor
@sentientthundertank2079
@sentientthundertank2079 2 ай бұрын
@Ermes12FloorSander thanks a lot my man!
@AngstG
@AngstG Жыл бұрын
Bad video, howcome nobody can tell what product or similar product to use, this is the most important piece of info...
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
the name of the product how to fill wood floor gaps is called Jenkins Joint Filler
@Ermes12FloorSander
@Ermes12FloorSander Жыл бұрын
instead the name of the dye to paint the floor is light oak stain
@benben-w7u5c
@benben-w7u5c Ай бұрын
​​@@Ermes12FloorSander👍❤
@fododude
@fododude 6 ай бұрын
High-speed video + no narration + garbage music = useless video.
@Ermes12FloorSander
@Ermes12FloorSander 3 ай бұрын
thanks for your opinion
@RiccoDelestaque
@RiccoDelestaque 3 ай бұрын
Vidéo absolument lamentable avec accompagnement encore pire.
@Ermes12FloorSander
@Ermes12FloorSander 3 ай бұрын
thanks for your opinion
@RiccoDelestaque
@RiccoDelestaque 3 ай бұрын
@@Ermes12FloorSander No wonder, have you seen the beginning of your video?
@Ermes12FloorSander
@Ermes12FloorSander 3 ай бұрын
yes there are some mistakes in the video i will try my best in the next videos. thanks for the comment
@RiccoDelestaque
@RiccoDelestaque 3 ай бұрын
@@Ermes12FloorSander The beginning especially is catastrophic, we don't know what it represents, you know, making a video without post-production editing is really very difficult. However, since cinema existed, the camera has remained fixed, it is the subjects that move everywhere, in cinema as in video. If we can be lenient because we are not all professionals, we must not forget that even an amateur document must obey a few rules. Those who view an amateur video are the same audience as in the cinema or television.
@Ermes12FloorSander
@Ermes12FloorSander 3 ай бұрын
thanks for the comment I will try to make better the next videos
@TGS2AUSA2024
@TGS2AUSA2024 2 ай бұрын
Absolutely no help at all unless their is a product link.
@Ermes12FloorSander
@Ermes12FloorSander 2 ай бұрын
I'll try to put a link to the product. Anyway the product is called jenkins joint wood filler gel. 👷‍♂️
@miajackson3559
@miajackson3559 Ай бұрын
@@Ermes12FloorSander exactly! Great work! Might send you my finished floor in couple weeks!! Thanks for this video !
@Ermes12FloorSander
@Ermes12FloorSander Ай бұрын
👷‍♂️👍
@thegravytrain1129
@thegravytrain1129 5 ай бұрын
What product are you using?
@Ermes12FloorSander
@Ermes12FloorSander 5 ай бұрын
The name of the product is morrells black varnish .
@thegravytrain1129
@thegravytrain1129 5 ай бұрын
@@Ermes12FloorSander thank you!
How to fill gaps in WOODEN FLOORS!!!✌(Part 2 of 3)
12:23
Hugo Correa
Рет қаралды 69 М.
Wood Floor Refinishing FAILS! 2 (YouTubers Fail so you don't have to)
25:49
How To Sand A Floor
Рет қаралды 279 М.
“Don’t stop the chances.”
00:44
ISSEI / いっせい
Рет қаралды 62 МЛН
how to fill old gaps to pine wood floors
12:16
Refinishing hardwood floors : Ermes12
Рет қаралды 1,4 М.
Should you FILL GAPS on a timber floor??
2:27
Quicksand Flooring
Рет қаралды 61 М.
How to fill floorboard gaps
5:55
Stanley
Рет қаралды 96 М.
how to fill, the gaps, of the pine wood floor
6:11
Refinishing hardwood floors : Ermes12
Рет қаралды 64 М.
I RUINED My Floor, Can You Fix It?
23:50
How To Sand A Floor
Рет қаралды 675 М.
What are the different ways to fill holes and gaps in hardwood floors?
5:25
Greenpointe Wood Floor Supply
Рет қаралды 91 М.
Beginner Wood Filling Mistakes | How to Fill Cracks and Gaps
15:30
YouCanMakeThisToo
Рет қаралды 645 М.
Everyone is sanding floors THE WRONG WAY
12:07
How To Sand A Floor
Рет қаралды 572 М.
Restoring 100 Year Old Floorboards. Is it WORTH IT?
11:50
How To Sand A Floor
Рет қаралды 415 М.
Pine floor repair and restoration - complete AMAZING project
3:03
Grain To Glory
Рет қаралды 279 М.