great of direct opens. not so great for pinched wires or intermittent faults. always best to do resistance checks while wiggling the harness at various locations.
@lcpd265 ай бұрын
True however you don't know the exact location of the problem in the wiring... Meaning that even if you wiggle wiring many times you don't know where, this helps allot getting a more precise location and wiggling same time.. You should check ohm resistance and wiggle it in general you might get lucky to break the circuit and same time use this Example you have harness that are behind dashboard... Can't wiggle them easily enough, mouse might have eaten it, you would need to take dashboard out, with this tool only cluster and radio out and you can find it precisely...
@mitchel24432 ай бұрын
Check for voltage drop
@enriquelopez9124 Жыл бұрын
awesome mechanic& job.
@user-cs3zs6jn1d Жыл бұрын
Looks like the wire was cut. But also demonstrates that the tool works. I'm skeptical on how accurate this is when there is a small break in the wire but the insulation is still intact. I've found several wiring problems after hours of looking that no tool would pin point.
@ZoidZoidZoidberg2 ай бұрын
It makes the wire into an antenna - the insulation doesn't help/hinder with radiation from the wire. I think partial breaks or breaks that only open up at certain angles will be a pain though :)
@borgsimpson93528 күн бұрын
So far ive only seen tutorials in open area access. Never in the cabin , under dash.
@kylen19222 ай бұрын
How do u use it on short?😊
@mzolisigotyi583220 күн бұрын
I'm in south africa, can I get one here too ?
@BatGS8 күн бұрын
Greetings: Ujunk so entertaining. In reading these comments; Of the many, it seems most most have little or no electronics / electrical knowledge, far less of the tool. Many of my repairs R that from most who think they know something, yet prove 2 have little respect and knowledge of the task. Those that have the overpriced toys, help my business.
@nwmartinzz4 ай бұрын
Great tool, but the problem that I have is the receiver too big if only the antenna be longer & flexible
@somphothbsiratsamy37487 ай бұрын
Just got mines yesterday, so stoked
@Jeezy11 Жыл бұрын
Dang now that’s a good tool
@ricardomartinez-nm3ex6 ай бұрын
I have it and I love it really great tool to have
@Elcopaneco10056 ай бұрын
Me puedes dar la información donde lo puedo conseguir gracias
@nitrous07me5 ай бұрын
Faster then just doing an overlay the the sensor/part back to the module?🤔
@jklcksmth1991bo23 күн бұрын
Whats thr name of that tool?
@coryjackson39934 ай бұрын
Did you unplug the computer to keep from shorting it out?
@danthecarman8440Ай бұрын
You have to know the wiring and disconnect both ends because the tool inputs a voltage and can damage control units.
@BatGS8 күн бұрын
Greetings: The tool outputs insignificant current. Therefore it cannot "short" components. However, it is recommended 2 use it open-ended.
@last1king Жыл бұрын
Share its link
@kornshadow0973 ай бұрын
That tool doesn't work all that great unless you have a obvious break or short. For an open it's not all that great. Instructions don't even say if the power needs to be cut or not... Either way it is hit or miss...
@kylen19222 ай бұрын
I thought the same thing untill I figured out how to lock the signal in. The instructions don't really explain this well.