How to find out if your ford fusion is wire up for fog lights

[@patrickwolbach]

Will this also work for the 2015 model? Where did you get that manual with the wiring diagram?

[@bradishler5967]

If it's not pre-wired does it make the process a lot more difficult? I don't know if I need fogs as I have a high quality HID kit and led high beam. But might if its not super expensive

[@golfchamp1991]

What about 2014 Ford Focus SE sedan?

[@u.c4183]

You just had to take the lights switch off instead of removing all those panels

[@Foxtrot2500]

What repair manual is that? Also were do you find the "plugs" for the fog lights and which dash switch do you need to buy?

[@Sick_ridz]

I have the exact same model SE and my harness has the grey 14 wire. I have everything I need, do I just splice my hot connection into the one grey wire for the fog lights to be controlled by the other headlight panel? I ordered that as well...

[@Nickthecarguy]

Kristopher Charles all you need is the front bumper wire harness that have the fog light connection and all you need is the headlight switch with foglight switch on it and fog lights

[@Nickthecarguy]

+Kristopher Charles if you have the gray wire your car got the fog light wired up so all you need is the fog light wire harness and fog light and headlight switch with foglight switch on it

[@MrKenwillis]

@@Nickthecarguy I have the gray wire on my 2013 fusion and when I pulled the bumper off and looked at the plugs on the passenger side they didn’t have wires going to the plug. They were dummy plugs😡🤬🤬😡. Can you tell me what I need to get these fog lights to work? I have the harness and the switch.

[@HEADBANGRR]

Hello Do you know if the black and gray wires are ground? Great info thank you

[@pzareba7]

I have a 2018 fusion se hybrid i took it apart and it does have a gray with brownish in it wire on spot 14. So what parts would i need. I know i need the foglights itself and the headlight switch. Would i need anything else?

[@Nickthecarguy]

You will need the fog light wiring harness I do not know the part number for the hybrids i would try to find a hybrid like your but with fog light and get the vin number off of it so you can order the part

[@pzareba7]

@@Nickthecarguy thank you very much for fast response.

[@BrianCornea]

Hi Nick. Thanks for the video. I also have a 2017 Ford Fusion that didn't come preinstalled with Fog Lights. I've always wanted to see if I could somehow install them myself without doing any wire modifications. Would I need to purchase a different knob to activate it once I install my Fog Lights?

[@Nickthecarguy]

You will need a wiring harness that have the fog light connector (I can find the part number ) and you will need a new headlight switch with the fog light button. I didn't need to cut or splice any wire it was all plug and play

[@BrianCornea]

Thanks for the response back. After I sent my comment to you I browsed your channel and found out how to replace that switch. Seems pretty easy. My only issue is activating it using the software. I guess I'll watch more videos so I can get used to it. If you don't mind posting that part number., I would appreciate that. Thanks! - Brian

[@Nickthecarguy]

@@BrianCornea no problem I can help walk you through to activate the fog light indicator. I do have a video on how to do it. You will need a obd device that plugs into your laptop you will need a windows 10 laptop

[@shellysdopevids6988]

Are 2nd generation Fusion S pre wired for fog lights? My 2011 Fusion S didn’t come with fog lights

[@waynenation678]

Thanks mate took mines apart and mines has it. But mane when you said do this first before buying them parts I done all the parts except the harness if it wouldn’t had work I’d be so upset with myself.

[@diggnetwork8393]

My wires are setup the same way on my 2018 ford fusion se. Do you think I can go off that and get the parts?

[@Nickthecarguy]

Yes if you have the wire then you should be good to add fog light

[@diggnetwork8393]

@@Nickthecarguy ok cool. Any idea on the part number for the fog light harness?

[@kezug]

Digg Network: did you do the fog light install on your 2018 fusion se? Was it wired like you hoped? If you did and it worked, can you share the parts or how you sourced the parts?

[@diggnetwork8393]

@@kezug Yeah I did it. I brought the front harness with fog lights. Part # hg9z-15k867-j.

[@kezug]

@@diggnetwork8393 Thank you! Do you have the part name/number for the lights, and the in dash switch? Also, what is your estimate on how long such a project will take?

[@Ant-mj9wf]

How many wires are on that connector?

[@joshualandis1498]

How many wire harnesses are needed? I have the one but it didn’t work. What is the part number for the harness below the driver side light?

[@Nickthecarguy]

You only need one wiring harness I do not know the part number for it unfortunately. I know there are different wiring harness depending what your vehicle have

[@2_busy_groovin]

I have a 2014 fusion S, im thinking about putting the fog lights, id have to check to see if im able to

[@Nickthecarguy]

If it's the s I would definitely see if it already pre wired I know the s verson is the stripped down verson where nothing is fancy on it so I would definitely before you buy all the parts and find out that it's not wired up for it

[@ianwilson1986]

I checked this on my 19 hybrid it has the wire there so I’m a good to get the bumper harness and related parts and also in forscan it says in bcm fog lights enabled

[@kennykane6799]

Trying to do this to an 18 focus se sedan. Have the new switch and 15k867 harness and the foglights themselves ordered. What wire am I looking for on the back of the switch for this?

[@Nickthecarguy]

That's a good question I'm seeing on my diagram that pin 1 which is red is a power and pin 5 is a lin bus and pin 7 is ground I dont see a wire for fog light

[@Nickthecarguy]

Looks like it runs off of lin bus so I dont think you need any wiring beside for the front bumper that have the fog light connector

[@kennykane6799]

Just switch out the switch and the harness on the bumper? Is it a similar task on forscan?

[@Nickthecarguy]

@@kennykane6799 not for sure on how to enable the fog light connector on the focus yet you would have to compair the data with one that have fog light and try one code at a time til it enable the fog light indicator

[@Nickthecarguy]

@@kennykane6799 try 720-08-01 xXxx-xxxx-xxxx make the big X C or try 720-06-01 xXxx-xxxx-xxxx make the big X 6 see if one those enable the fog light indicator

[@tayyabahmed]

Which manual is this?

[@sayid534]

can u do a video how to wire fog lights

[@Nickthecarguy]

I have a video talking about what you need to add fog light I unfortunately don't have a video of me actually doing it. You do have to pull the front bumper off. You also need a wiring harness that have the fog light connector

[@kevinengle2000]

‘there all wired for fog lights and you only have to take out the head light switch

[@isaiaheckert4429]

The other way to tell would be to pull the bumper off and look for the harness(es) for the fog lights within the front end

[@Nickthecarguy]

Yes but it a lot of work to remove the front bumper this was is easier

[@kerrynorwood7151]

so i had my fog lights install yesterday and there not working at all the i look at your video and everything match up but there not coming on im thinking i might have to use forscan to unlock something what do you think

[@Nickthecarguy]

What kind of fog light did you add? I didnt really need forscan to activate it only just to activate the fog light indicator but that have nothing to do with the fog light not working

[@kerrynorwood7151]

@@Nickthecarguy I Got The LED Fog Lights

[@Nickthecarguy]

@@kerrynorwood7151 I know the led one that I have they only work one way you could have got it plugged wrong. Unplug it and turn the connector upside down and try to plug it in. Also could you not have plugged the connector in all the way on the light or to the body of the car

[@kerrynorwood7151]

@@Nickthecarguy ok im going to go check it now ill let you know if that works

[@Nickthecarguy]

@@kerrynorwood7151 also high beam must be off for fog light to turn on headlights need to be turned on for fog lights to activate

[@shariqhussainmohammedshariq]

Does this technique work on all ford vehicles

[@Nickthecarguy]

shariq hussain yes kinda you would need a wire diagram to see what wire is for the fog light for your vehicle this video here is for the 13-18 Ford fusion

[@rudyg5955]

I have a 2017 fusion eco boost please help me

[@Nickthecarguy]

What are you needing help with

[@mohmeadable]

hi i m really need help too i have mustang 2016 and i dont have fog light i buy everythink this switch in ford fusion i have in my car but i need to know where is will for foglight to countact i m really need help guys

[@Nickthecarguy]

Its behind the front bumper on the fog light connection. You will need to order a wire harness with fog light connector

[@marchannah1884]

Where did you get the wire diagram book?

[@Nickthecarguy]

I got mine on ebay

[@gafurrzogaj1426]

You didn’t really need to do all that work the most simple way to check is to look at your lights switch if it has the fog light button on the switch then it means it’s wired for fog lights save yourself lot of time 👍

[@Nickthecarguy]

Mine didn't have the fog light button this car was a base se version

[@wandamcgann7728]

mine is yay!!!

[@Nickthecarguy]

+techygrams 2017 all you need is the fog light wire harness and the fog light ASSEMBLY