HOW TO FIX LOSS SUCTION ON DYSON DC25 | CLEARING FILTERS | UNCLOG DYSON

[@how2not22]

Dyson DC5 Animal - amzn.to/3lfYM6W

[@ritadifebbo560]

Thank you sooo much for this! I did what you showed and there was a huge clog in the hose!!! I cleaned it out and it's as good as new! I'm so happy!!

[@mikkidthe12c]

On inside if the hose there is a clip to realise hose

[@Faithamberly]

Ty he vacuum hose comes apart under the cyclone body. There is a little thing you push in at the bottom / touching towards the back of the vacuum.

[@marinashaw6389]

The clip for releasing the hose is at the rear of the bin. It is not immediately obvious it is actually a clip. Take of the bin and you will notice that there is plastic with a couple of ridges on it. That is the clip. Press this clip and the hose will come off.

[@how2not22]

Thank you!

[@sondosatrash453]

thanks i need help, my ball is stuck! can you tell what the cause?

[@Andreatube96]

Hi theres a clear circle that's on your dyson too near the filter that snapped on mine do you know how i can fix it

[@johnpoole755]

All tubes ate clean, motor runs, but still no suction. Any ideas?

[@sandrawhite6025]

I change the lower duct hose. I need to chane the changeover valve because it is dry rotted could you tell me how or show on you tube. Thank you

[@Saint139Jizzle]

Im getting loss of suction because i took the wand out but when i put it back and its too long. There is a vent at the bottom of the tube that is wide open because the wand is now too long… she mentioned this in the video

[@sady1cute540]

Thanks for this - I was stuck with my Dyson and this was v easy to follow.

[@robingadd1216]

Excellent video - thank you ! Complete loss of suction. Large tennis ball sized ball of debris found under the filter cover. Removed and replaced. Dyson working good as new. Marvellous :).

[@markreed171]

Button is behind the canister

[@joec3574]

You can disconnect the bottom of the long hose by taking off the bin that holds the dirt and press the release button. ( see hose replacement for the Dyson DC 25 on KZbin). Your welcome.

[@justice2bserved107]

Remove the canister and there is a button on the inside to remove the hose from the bottom they are inexpensive on Amazon

[@generalzod7959]

I've got this model. Right now, there is no suction and the brush roller isn't moving. This could prove difficult to figure out.

[@michaelallport5901]

For tge hose you can't remove . Look sound the front after removing cyclone. There is a button to release tge hise

[@dogsarethebestcatsaretoo6764]

How do younopen the nozzle in that model?

[@how2not22]

hi, First of all lie your dyson flat on the ground, underneath the nozzle head you will find a button to release the nozzle. Make sure the power is switched off.

[@ralphprunella8031]

There is a button behind canister to remove bottom hose

[@tabithabevers4088]

There is a little clip in the front of the vacuum that you push back and it pops out.

[@heyhayhay9581]

Thank you so much for this easy to follow video! You really helped me out big time!!!!

[@how2not22]

Glad it helped!

[@harveyg5707]

Do you still have this

[@how2not22]

No, I have a Henry now.

[@harveyg5707]

HOW2 NOT2 oh that’s a shame

[@harveyg5707]

How did itbreak

[@hoovermaster]

How many vacuums have you got?

[@how2not22]

Not as many as you! ☺☺

[@hoovermaster]

+HOW2 NOT2 Well I am very slightly a collector hehe

[@hoovermaster]

HOW2 NOT2 Thanks for subscribing!!

[@gordonstewart716]

To remove the rear hose remove the cyclone body and there is a button just to the right of the clear plastic disc ;-)

[@how2not22]

Thank you so much!

[@litzyolivanaguilar1116]

This was so helpful! Thank you got my Dyson working like new ❤️

[@how2not22]

Glad it helped!

[@brianmott728]

I own that same model. It makes a whistle when I turn it off. I discovered the whistle comes out between the filter and the motor. There is a little slop between the filter and the motor. Is the small gap causing that noise or is it because that filter is dirty? Could the motor housing be warped?

[@jenmor1231]

You need a new ball filter. Mine did that and it was a slight vibration between the seal and the part it clicks into. New filter and noise is gone

[@SuperDoright]

Thank you!

[@monashamsan3096]

Thank you

[@TheWinezen]

Great video. I love my Dyson dC25

[@Paul-et1fm]

THANKYOU VERY MUCH.😊🏵

[@how2not22]

Most welcome 😊

[@amberbludnick6402]

works well

[@therookie5263]

Thank you Jesus !!!! the awesome video....it was extremely helpful and resolved our DC25 auction issue

[@zipmicz]

Amazing!!! Amazing!!!

[@how2not22]

Thank you! Cheers!

[@richardbaguley5405]

Nope. It's a design fault, with a brush fitted to the hose there is no suction whatsoever and it was like that from new. Dyson engineer said they're all like that.

[@dannydirt5D]

You should never wash the filters as you will never truly remove all the dust and dirt particles. Adding water will only turn the remaining dust and dirt to mud therefore causing more problems and could even blow the motor.

[@Mudge07]

Sto79Be agreed, the 3-monthly rinse-through is labelled on the chassis (vortex -head, coloured casing on new items) and owner’s documentation. Prior to washing lightly brush off the surface dust into an open, lidded bin out of drafts or wind flow. Always wash out in the direction of airflow. A wet filter, if insufficiently dried will be an electrical hazard and quickly clog the filter thus loading the motor’s components and wasting excessive energy. If there is damage to the filter then it should be changed and one that doesn’t show signs of cleaning even after a proper rinse cycle would also be replaced.

[@coryengel]

Dyson’s instruction is not to merely rinse them, but also give them a hard whack alternating while rinsing, and do it 10 times or until the water runs clean. The real key is doing it every 3 month. Waiting longer will make it harder to rinse them successfully.

[@dmcr8171]

As you requested, How to disconnect the hose, kzbin.info/www/bejne/jWTdfah_qKebh5I

[@rosered8234]

I wanted to know how to remove the big tube ... you didnt know I dont think you should have done a video where you did not know how to dismantle fully ... i watched right to the end for you to help me on how to take the big tube bit off ... you didnt know This was not helpful 😞😞😞😞

[@mynameisnothere9465]

Gee, that sucks so bad that this video that was made specifically for you and your issue didn't address it properly. It also sucks that there are absolutely no other videos out there on the internet about fixing dyson vacuums. Tough break.

[@how2not22]

Sorry about that, please read Marina Shaw's comment from 2 years ago, she answers your question. "The clip for releasing the hose is at the rear of the bin. It is not immediately obvious it is actually a clip. Take off the bin and you will notice that there is plastic with a couple of ridges on it. That is the clip. Press this clip and the hose will come off."

[@TheLaura926]

*Overall 5 stars as it's exactly what we wanted,🧼 **allabout.wiki/Dyson-Upright** in terms of cleaning power. Suction is as good as all the reviews state. When we first got it, I first vacuumed with the existing vacuum and then with this, the additional fine dirt that was in the Dyson was gross and convinced me we needed this. We have medium length carpet and a terrier - no issues, I do imagine plush carpets would not work well with this. Also a little too powerful for most bathroom rugs. Great for area **rugs.One** con is the hose, it's great for reaching far away places (ceiling), but is frustrating and hard to use if you're within arm's distance (think couch and floorboards). This is due to the design of the hose having this long metal rod for extension. Also, I haven't figured out how to get the hose back together quickly as it's supposed to nest into the base of the vacuum. This piece might just be user error though.Canister is just like all others, still have to take out the middle insert to get all the dirt out. I often make a mess around the trash as I'm trying to empty it, but the suction picks that right back up.*