[HOW TO] Fix Noisy Leaf Springs - Install a Spring-Thing (Pretty Much Any Pickup Truck)

UPDATE: These should work on pretty much ANY pickup with leaf springs. Not just GM models. Most pickups have similar type leaf spring setups, that would allow this to be installed in a similar fashion as the video.
This video shows a way to mitigate clunking and noises from the rear leaf springs on a 2nd generation (2015-2021) Chevy Colorado or GMC Canyon. This will also work on a 2014+ Chevy Silverado and GMC Sierra. This process can reduce the amount of leaf spring slap. Cheap and easy to do.
=====================================================================
Visit the Spring-Thing Website to get your own set: www.spring-things.com
=====================================================================
Here was my previous DIY fix on my 2017 Colorado:
• [HOW TO] "Fix" Noisy/C...
Here are the rubber sheets I used in that video:
amzn.to/2TNpmoi
=====================================================================
Check out my Amazon Store Front!
www.amazon.com/shop/fondupots...
Other stuff I like to use:
Work Gloves: amzn.to/37jel2a
Milwaukee Impact Wrench: amzn.to/2RgJJJ5
Makita 12v Impact and Drill Set: amzn.to/2TW5gIP
Makita 18v Impact and Drill Set: amzn.to/30GVyLy
Makita Drill Bits set: amzn.to/37ie538
Go Rhino! Digital Pressure Inflator: amzn.to/2G8x6t8
Dewalt Socket Set: amzn.to/2GdmUzq
Craftsman Torque Wrench: amzn.to/30GZzQd
Trim Removal Tools: amzn.to/37gjRSR
Oil Drain Pan: amzn.to/2vbQZ08
Oil Pump: amzn.to/36fxyAf
Shop Towels: amzn.to/2NLimok
Chemical Guys Inner Clean amzn.to/3azFvDE
Shure MV88 iPhone Microphone: amzn.to/2BMdbRT
Get Amazon Prime: amzn.to/2RdYigg
--As an Amazon Associate I earn from qualifying purchases.
#ChevyColorado #chevytrucks #CanyonColorado #fondupotsgarage

[@fondupot]

One thing I forgot to mention in the video. If your truck has a rear sway bar installed, you will need to first disconnect the end links from the bar, before you attempt jacking up the truck. Otherwise, you will not get full droop on the leaf springs, and it will be difficult for you to slide the rubber pads in between the leafs.

[@alandhigdon]

100% recommendation. It took 30 minutes to install and completely fixed my 2018 Silverado!!

[@antoniostewart9650]

Did you have to remove anything or does it work exactly as the video? I have a 2018 as well....passenger side is squeaking...driver side isn't so far

[@fondupot]

Don’t need to remove anything.

[@YourHairyGodmother]

Love the two perspectives of installation. Great vid as always!

[@fondupot]

thank you!

[@coryturner9140]

Works like a charm. All my noise is gone after 20 minutes of simple install

[@fondupot]

Awesome!

[@WhatsupWorldPodcastLLC]

Very thankful I found this video. Had my 2014 Sierra at the dealer 3 different times and they couldn’t find the issue. They greased it and the noice would be gone until it rained or I washed the truck. I’m praying this works as it has for everyone else. Purchased two sets just to have back ups.

[@fondupot]

They work great. Should help your 2014 out for sure! Thanks for watching.

[@FrenchyLP]

I noticed a squeak at just 25k miles in my 2016 Colorado. I got the truck to handle some tougher terrain for work, and squeaking around the jobsite in a newer looking vehicle was a tiny bit embarrassing. I found myself driving more carefully than I did in my previous work vehicle just to avoid the noise! Going to order a set. Thanks for finding these!

[@fondupot]

Give your leafs a good power wash before installing if they are super dirty. Should help even more. Thanks for watching! Glad to help.

[@johnrogers4259]

Just got these and put them on my 22 Colorado. Was seriously considering getting rid of it because if the clunking in the back. Fixed the problem immediately! Great video! Thanks for making it!

[@fondupot]

Glad it worked! Thanks for watching

[@kenmcvicker]

Awesome solution. I had my truck into the Dealer 3 times for this. Now it is out of warranty. I am buying these today. Will let you know how it goes

[@fondupot]

It should help. Thanks for watching! Good luck

[@zr2overlander323]

Dont usually make comments but this product simply works and easy to install. Had an annoying as hell squeaking sound coming from the front of my left rear wheel well. Knew it was the leaf spring and hinestly did not want to use a lubricant because of the attraction of dirt. Luckily I came across this video and decided to give the product a try. Truck is now quiet and could not be happier. 2019 Chev Colorado ZR2 Bison.

[@fondupot]

Thanks for posting! Glad to hear they helped you! Thanks for watching.

[@cflip7452]

Just did Hummer H3 that’s basically the same as Colorado. Seems to have taken care of most of the leaf spring slap on those jittery road! Great product and great idea plus shipping is outstanding

[@fondupot]

Great to hear! Glad it worked out for you! Thanks for watching

[@johncherry2096]

I was skeptical concerning this product. Dealership fixes didn't work and spring replacement was my next option. Thought I would give these a shot so ordered a set and had them installed in 15 minutes. No need to remove tires and wheels from my 2009 silverado as could reach where I needed to be without much hassle. I still doubted how something so simple would work but jumped in and started my test drive and within 20 feet I realized that this was IT!. Pulling out of driveway was usually squeaky and loud as I turned onto the roadway and continued with every turn or bump onto a new surface. There was NOTHING! Not a sound from the rear springs. It was like a brand new truck and I couldn't believe it. Give these things a try and get rid of those horrible squeaks. GREAT PRODUCT!!!!

[@fondupot]

Glad to hear!

[@endanzeron5662]

Did this just using rubber on my bt50. Worked a treat.

[@SingleMaltAndMaps]

Just installed these on my 2020 Sierra elevation. Worked like a charm and the suspension is as quiet as a mouse . Great video and awesome product.

[@fondupot]

Awesome to hear! Thanks for watching.

[@Dan007UT]

Single- what noise WAS it making before hand?

[@SingleMaltAndMaps]

@@Dan007UT every time I pulled out of my driveway, or went over bumps at slow speed the leaf springs would clunk. Mostly on the drivers side. Sounded like I was driving a truck 30 years older

[@Dan007UT]

@@SingleMaltAndMaps I get a lot of clunking anytime I'm offroad but on road I get nothing. I'm about to throw these things on. The clunking and squeaking almost sounds like it's coming from the front but I'm hoping it's all in the leafs!

[@SingleMaltAndMaps]

@@Dan007UT when my truck was at its worst, I could rock the back end side to side by the wheels and it would clunk

[@sniperalez]

Worked on my 2023 GMC AT4 with 1,400 miles on it used to sound like ball was in the bed. After the dealer said it was normal along with GMC "Technicians."

[@fondupot]

Sounds about right! Glad it helped you out.

[@marineinneed]

So I changed my whole Suspension and also found out that my 2015 Chevy Silverado was missing the transmission mount but on bottom and after I did all that still made noise added this product and boom it’s fixed thanks so much

[@fondupot]

Great! Glad it worked. Thanks for watching!

[@BernPisarcikJr]

Will install in my Colorattle. Thanks for the review bud!

[@fondupot]

Awesome. Good luck!

[@spring-thingllc8342]

colorattle! lol good one! Thank you

[@spring-thingllc8342]

Thank you for the review video!

[@fondupot]

Anytime! Thanks for providing the product!

[@renesolis8812]

This is great! I was wondering why Chevy or GMC never recalled this issue. Looks like a simple enough fix though. Thanks for sharing.

[@fondupot]

The official GM repair procedure is to grease the hell out of the leaf springs. Not sure why it hasn’t been fixed in engineering. Probably a cost issue. Glad to help. Thanks for watching.

[@alejandrocelio5941]

They actually do have a service bulletin sayimg yo replace those rubber isolators.

[@ericg.1571]

@@alejandrocelio5941 should i do the bulletin or just use these? Alot of people did it with dealership and noise continued until they used the spring things

[@fondupot]

The bulletin is a temporary fix. These will last for the life of the truck.

[@avflyguy]

They only issue Recalls for safety things. Seat belts, brakes, air bags, power steering, ad nausea..... Service bulletins sometimes fall 1/2 way between recall and bulletins.

[@InJasonsGarage]

Hey, that's pretty cool. I didn't know I needed that. If I don't, I probably will in the near future! Thanks for the review.

[@fondupot]

Yea these helped quiet the springs on my Canyon. Definitely a nice little product. Thanks for watching!

[@InJasonsGarage]

@@fondupot You bet. Thanks for the info. Is there any trick to disconnecting the sway bar or is it strightforward?

[@fondupot]

Very simple. Before jacking up the truck just remove the bolts on the end links. Mine came out really easy.

[@InJasonsGarage]

@@fondupot Cool, thanks.

[@fondupot]

You bet! Good luck

[@chrismyers5437]

I just installed these on my 2018 Silverado and they took care of the noise. Great product, I highly recommend it. Thanks for the detailed install video, appreciate it.

[@fondupot]

Awesome to hear! Glad they worked for you. Thanks for watching!

[@shanestone100]

What does your noise actually sound like? I just bought a used 2018 Silverado and it sounds like an old wooden floor creeking, or like an old set of wooden steps. Not a squeak, but more of a creak sound, if I’m making sense?

[@shanestone100]

@@fondupot could you describe the sound? Squeak? Creak? Mine is more of a creak sound like old wood floors

[@fondupot]

Yea. A creak could also be the leafs. But more often the sound is a clank or clunk.

[@chrismyers5437]

@@shanestone100 yes, mine was creaking not squeaking. I would also describe it as a knocking/clanking sound and since I installed this product all sounds are gone and truck is as good as new.

[@jinglezman]

Awesome video Ty for sharing. My 2020 zr2 is making the noise. Now I have the solution. Truck was at dealer for 2 weeks and they said nothing is wrong lol.

[@fondupot]

Dealers are usually worthless, give this a shot and you'll be satisfied. Thanks for watching!

[@robeacott4436]

Great video! Simply and easy. I'd definitely take the wheels off. I can see fighting with the screwdriver up there. Thanks!

[@fondupot]

I did the passenger side off camera without removing the wheel it’s not that bad. Thanks for watching!

[@spring-thingllc8342]

@@fondupot I didn't remove the wheels when I installed them in my 17 sierra :)

[@sterlingjcalvin]

Well I guess I’m buying this now ha. Replaced my leafs on my 2015 Silverado in 2018. The issue was back 6 months a later. Thanks a lot guys

[@fondupot]

Glad to help. Thanks for watching

[@sterlingjcalvin]

Silence is a beautiful thing 🦾 We’ll see how long it lasts Thanks again man

[@dodgejay545]

Excellent video .. I will try this on my F150

[@fondupot]

Thanks. Good luck. Should work perfect

[@claddagh1000]

2015 Sierra here and just ordered 👍

[@fondupot]

Hope it helps!

[@Emvilla25]

Just ordered one. Clunk on my 4 day old 2022 Silverado is driving me crazy. Dealership was about to replace the leaf springs. Going to try this first.

[@fondupot]

I hope you get them. I’ve heard reports shot the company has not responded to orders recently. Be sure to follow up with them if you don’t hear anything after a few days.

[@jinglezman]

I just put these on my 2020 colorado Zr2. All of the noise that it was making is now gone. Amazing product and great video. Thanks so much

[@fondupot]

Glad to hear. Thanks for watching!!

[@spring-thingllc8342]

Thank you for the review!

[@cflip7452]

One Thing I just found out is after installing these I was still getting a little noise. After more hunting I got a 18mm attached to 1/2 torque wrench set at 86 ft lb. and checked all frame mount bolts which was a total of 6 on my vehicle 2007 hummer h3 mainly concentrating on passenger side considering that’s where the noise was happening and like magic noise was gone! One thing to think about and in my situation I mainly drive by myself so there’s 200 more pounds on drivers side at all times and cab flex was part of the culprit! This should apply to most Chevy vehicle considering hummer h3 is based on Chevy Colorado or Canyon frame. All and all me concentrating only on leafs springs was only half of the problem. Also sprayed silicone lubricant on all rubber mount frame cushions. We’ll see how long it last but all is well from the annoying chirp I would hear at low speed small bumps which reminded me of my dads old Chevy pickups but not quite to that extreme but similar. Hope this helps someone with same issues

[@dna59]

Definitely getting these! Thank you. I greased mine and that fixed it but washing my vehicles so much it doesn't last.

[@fondupot]

Yea, greasing the leaf pack is the dealership fix. And it's been proven to help, but does not last very long. The rubber pads should do the trick. Thanks for watching!

[@spring-thingllc8342]

That's what I was doing for a few month's before I came up with the idea for the spring-thing. :( That got old pretty quick! I actually hated driving my truck for a while lol These will make you like driving your truck again :) They also do away with that clanking sound these trucks make.

[@dna59]

@@spring-thingllc8342 yes my problem is the clanking. It's amazing how something so simple can make your truck sound like it's falling apart. I hate driving my truck with that noise...it's embarrassing. Greasing the leafs get old quick!

[@chawnyray]

Just ordered a set, I know it won't resolve the ridiculous axle 'free-floating' thunk but hopefully it dampens some of that noise coming from back there. Thanks for making it easy and not overpricing it. It's actually cheaper than a full 1/4 mat and the time that would go into cutting IMO.

[@fondupot]

Glad to help. Just FYI. This is not my product, just did a review for the Spring Thing folks.

[@spring-thingllc8342]

Thank you!

[@Mr.Beastforpresident]

Did it resolve the thunk? My truck has it too.

[@mckeznak]

Wow just threw these on my 2019 Silverado instant fix quick install can't believe it. No more weird looks at the Timmies drive-thru... well at least not for the squeaking.

[@fondupot]

Haha. Right on.

[@Losky79]

Just put these on my 21’ Sierra 1500 AT4. They worked as advertised, no more pooping or thumping coming from the rear end. I took it for a test drive after installation and flexed the crap out of the truck, not a single peep from the leaf springs. Just a bit of advice, when installing these using a floor jack, do not lift from the Rear Differential “Pumpkin”, it doesn’t help. The leaf springs are still compressed if you lift it from the “Pumpkin”. What I did is lift it from the rear of the bed, underneath where the hitch is located. I didn’t even lift the wheels off the ground, I just lifted it high enough to relieve the pressure from the leaf springs. Once you do that, it takes less than 20 minutes to install. Remember, always use jack stands for safety!

[@fondupot]

Correct you need to droop the suspension in order to install these. Lifting from the frame works too.

[@greenfire919]

Did you install the pads in the same location as in this video?

[@Losky79]

@@greenfire919 yes, the exact location in the video 👍

[@chrisbodiford4070]

Just put a set of these on my 2020 Ford F150 and it was obvious that they solved the squeek/screech as soon as I lowered the truck! These are well worth the money paid. Pretty easy to install also.

[@fondupot]

Great to hear. Glad you got it fixed up!

[@chrisbodiford4070]

@@fondupot thanks for the video and recommendation!

[@fondupot]

You’re welcome! Thanks for watching.

[@speckledtroutfisherman1619]

Will they work on f f250 6.7

[@speckledtroutfisherman1619]

Ford f 250 6.7

[@geovanyfelix4955]

Just put an order in. Don't usually go through the comments. But same issue. 2018 COLORADO ZR2 with about 60k miles, started around 30k. Dealer couldn't find the issue. Clunking in the back is annoying, any little bump. Lets see how these work out. Looking forward to them.

[@Glamisemt24]

Do you have the measurements of the pieces. Think I can make them

[@forgottenknowledge8917]

Great idea. I've got some scrap rubber. I'm gonna cut some up and do this.

[@fondupot]

Should work great.

[@genesullivan3487]

Just put them on my 2019 Silverado and wow what a difference. I hope they last!

[@mrbrianf]

Hoping this will work on my just purchased 2018 Silverado. My only difference is this truck was lowered. But I figured out sound was from right where you first showed in video, the front bracket around top 2 leaves. The dealership putting me off because they realize they are Ford service lol, but I will spend on this item and I bet problem will be solved.

[@fondupot]

Glad to help thanks for watching

[@MA-iv7ol]

I installed these on my 2018 Silverado a while back, hasn't made a sound since. I can't believe GM hasn't corrected this issue on the newer model trucks.

[@fondupot]

Glad it helped!

[@nodakgarage7312]

My 2020 f150 was popping and clunking. Never seen this issue before working in a shop dealing with these trucks all the time. I’m sure my truck has a defective leaf spring or something and the dealer says it’s normal lol. I replaced the isolator pads and that fixed it for 6 months and now it’s back so I’m gonna get this and call it a day

[@fondupot]

Good luck!

[@chaspatterson2555]

I have a 2011 f150, my springs measure 3". I just ordered the kit so I will let you know how well they work.

[@fondupot]

Should probably still work out for you. Report back though!

[@thomasrocksit9775]

DID IT FIX THE CLUNK ?

[@abrlopezz]

Thanks brother

[@fondupot]

You’re welcome thanks for watching

[@RyanHarvill]

Just installed mine today and did exactly as advertised. Now I’m compelled to return to my dealer with my brand new 1k miles 23 Silverado to say this is proof it’s the leaf springs and that they need to fix it.

[@RyanHarvill]

Also meant to ask, how long do folks think these will last. I am slightly concerned about it not working for long, but only slightly. They appears to be very durable and certainly better that the piece of crap Plastic they tried to solve the problem during manufacturing.

[@fondupot]

Glad to hear they helped. I’ve had mixed reports of longevity. Mine are still fine. But my truck doesn’t have very many miles. Over time and with extended exposure to the elements, the rubber can break down.

[@RyanHarvill]

@@fondupot thanks for responding. These have saved me from making a rash decision and selling my truck because of the clunking. Thanks again.

[@fondupot]

Glad to help.

[@Saltwaterassassin]

Had both leaf packs replaced on my 2023 Sierra 1500 and still making sound. Gonna have to give this a try

[@claddagh1000]

Just installed mine on a 2015 Sierra and will update when I go for a drive

[@fondupot]

Hope it works out for you! Should eliminate most of the noise.

[@lijuakumar6168]

Thanks 😊

[@fondupot]

You're welcome. Thanks for watching!

[@ricardocanul2413]

I just bought a 2020 Colorado wt. whenever I pull in side ways into my drive way, my bed sounds like it’s loose or rattling, cuz I pull in at an angle. If that makes sense. Maybe this spring thing will help with the clunk?!

[@fondupot]

Yea, sounds like the typical spring slap that happens with these trucks. These should help! Thanks for watching. Good luck!

[@robertsheffer9183]

I installed these a year ago on a 2014 Sierra 1500 with a lift and they were quiet, for a while. I was under the truck washing it about 6 months later and the zip ties were broken on a couple and they were flattened out and slipping out of the spot. Not sure if I'm too aggressive with my occasional off road driving but $45 every 6-12 months might be better off buying a new set of leaf springs.

[@Saltwaterassassin]

I had the dealer replace both driver and passenger leaf packs and sound still exists on my 2023 Sierra 1500. The fact GM has addressed this correctly is insane

[@mcool4587]

any ideas on how to get rid of the wind whistle noise on the rear slider on my 201 ZR2? Its driving me crazy above 40 mph!

[@fondupot]

Honestly no. That’s the first I’ve heard of that issue. Maybe make sure the track is clean and seals correctly.

[@IOwnCalculus]

Did you disconnect the rear sway bar link to get the axle to droop a bit more?

[@fondupot]

Yes an absolute must. I didn’t mention it in the video because most people don’t have a sway bar. But I just removed the bolts on the bottle of the sway bar end links.

[@killer-hm4ju]

Nice

[@BoStErO1905]

would it be better to remove the original isolaters before installing the spring thing?

[@fondupot]

No. I wouldn’t.

[@brentperkins6521]

I have a 2006 Sierra Crew cab and I recently replaced the leaf springs and went with the 2013+ GM springs. They are a direct fit but increase the payload capacity by a few hundred lbs. Almost immediately I noticed a lot of clunking or rattle from the springs when going over bumps. Will these fix that?

[@fondupot]

Should help yea.

[@timr0by]

So, can you do this without jacking the truck up? Or is jacking it up a must? Also, do you remove the factory pads, or just add these on top? Thanks.

[@fondupot]

You absolutely need to jack up the truck. When the weight of the truck is on the springs you'll never be able to slip the rubber pads in between the leafs. Jacking up the truck allows the leafs to droop and then you can pry them open slightly to slip in the pad. Thanks for watching.

[@youngeaon6284]

I had the same issue so I sprayed them it stop making noise but those pads will fix the problem for a VERY Long time

[@fondupot]

They sure do! Thanks for watching!

[@NismoS13240sx1]

Easy install took about 15min spring clunk gone on 2016 gmc sierra all terrain dealers quoted me 480 to do and 2.5 hrs labor not covered by warranty

[@fondupot]

Glad to hear!

[@NismoS13240sx1]

@@fondupot thanks for the video brother

[@francisalvarico3026]

How long have you had the spring things installed? Any issues since installed?

[@fondupot]

About 6 months. No issues 👍🏼

[@speckledtroutfisherman1619]

Hello, we’re did you get those rubber pads at , is that better than installing the shims and also will They work on a Ford f 250 , I’m getting a squeaky sound from the rear and I can’t figure it out we’re the hell It’s coming from

[@fondupot]

Check the video description.

[@dylanarmstrong3880]

I have a 21 Silverado 2500HD and was having issues with the leaf springs. I was able to install this product on the front end of the springs but couldn’t get to the back because it was too difficult. The noise seems to have gone away but the fact that only the front end springs have them, bothers me like an unbalanced equation. Should I try again to install them in the back? Is it fine as it? Thanks for the video!

[@fondupot]

Makes sense. The heavy duty springs are much stiffer and probably a lot harder to separate. I don’t think it’s harming anything. If your noise is gone, I’d say you’re fine. Thanks for watching.

[@Irv808]

I’m trying the same thing on a 24 2500 and the rear is such a pain. But it still makes the noise. I was only able to put the front.

[@jeffbrown7529]

I have the '17 full size GMC. it has only three leafs'. Im struggling with the front installation . Jacked it up removed the tire, only about an inch from the overlap. I tried the area before the bracket wrap, but the noise is still there. Any suggestions??

[@fondupot]

Hmm not sure. It’s not gonna remove all the noise. But it should at least be improved some.

[@ryangalvan1669]

I don’t have a Jack. Do you have to Jack up your truck to install??

[@fondupot]

Yes. You have to take the pressure off the leafs in order to slide in the pads.

[@timc524]

What about the other leafs? Seems like need 4 each side?

[@fondupot]

You can’t fit one between all the leafs. Unless you use much thinner material.

[@gfp400]

did you have to adjust them from time to time?

[@fondupot]

I haven't touched them yet since installing them.

[@GinnieJo]

Ok.. I have a 2016 GMC Canyon All Terrain and I’ve noticed for well over a year now that the bumps cause the squeak BUT ONLY when I press on the brakes going over them. I’ve tried bringing it to the dealer but they couldn’t find the issue.. are you telling me this is the same issue I am more than likely having?! 😳🤯

[@fondupot]

Could be! Give it a shot. Good luck!

[@seanwalker7496]

I made mine out of 1/4 inch rubber…now my rear suspension feels so rigid..did you have this experience after the install?

[@fondupot]

Hmm no.

[@pengzhu6783]

I use the shoes molding rubber did the same thing but still didn’t solve the issue. Who can help me out

[@fondupot]

Not sure what you’re saying...

[@eddiescoseria5884]

Can you please help? I was able to install the rear passenger side leaf spring. That one itself was really hard. The front I can't get it open enough. I kinda gave up for now. I have a 2022 silverado and now sway bar. I also lifted the rear tire to do it. Any thoughts? Thank you

[@fondupot]

Try lubricating the pads and then sliding them in while you open the leafs.

[@eddiescoseria5884]

@@fondupot I was thinking of putting a shim in there lol. I busted my finger trying to pry it open with the screw driver lol it slipped out 😅

[@richapocalypsesg1949]

So you don't need to removed the old buffers?

[@fondupot]

Nope. Just skip these in between.

[@209Stretch]

Did you install the spring things over the factory isolators or did you remove them? I left mine on with the spring things over them & it’s still squeaking like mad.

[@fondupot]

Yea the factory pads remained. You can try greasing the pads up and see if that helps. Mine still squeaked a little after the pads tho.

[@irvdimont739]

My 2019 Colorado started squeaking at 9000 miles. Dealer change the springs and 1000 miles later, noise returned. We back to dealer, and they tried doubling to factory rubber pads and lubricating the springs. Worked for 500 miles. When factory warranty expired, installed spring things. Took me about 1 hour. So far noise gone. Fingers crossed.

[@fondupot]

Glad to hear. Thanks for watching.

[@irvdimont739]

Noise returned after about 400 miles. Very disappointed.

[@fondupot]

Sorry to hear. Try repositioning the pads.

[@irvdimont739]

It appears that the creek is coming from the front spring bushing. Tried spraying with lubricant, but no luck. Guess I just have to live with it. This is my last GM vehicle. Shouldn’t sound like an old work truck starting at 9K miles. Spring Thing might have worked if the noise came from the leaves themself. Let’s see if my wife will let me buy a Honda Ridgeline (if I can find one without a dealer markup).

[@Aberod155]

Will this work with a 2020 chevy silverado trail boss. The TB comes with a two inch lift. Not sure if this would matter. I see in the description it says 2nd gen but wanted to double check. Thank you

[@fondupot]

Yea it should work fine. Pretty much same process to install on a Silverado. Thanks for watching. Glad to help.

[@scottheathsh]

Does these work on Ford? I have a 2020 Ford f150 1600 miles on it. I have a noise also I'm thinking its the leaf springs also

[@fondupot]

Should work the same yea.

[@scottheathsh]

@@fondupot thanks. Maybe I'll try them

[@fondupot]

Report back after you do and let me know how it went!

[@scottheathsh]

I will. My trucks under warranty. So I have to talk to the dealer first

[@ChargerDad]

Video states 2014+. Are the springs different on a 2013 Sierra? Will these still work as intended? Mine are awfully noisy when not lubricated.

[@fondupot]

This should work on pretty much ANY pickup with leaf springs. I need to update the description...

[@williamhunter658]

I was wondering the same thing Garth Mattson because I have a 2013 Sierra, I only have three leafs on mine, not much overhang. Did you try them?

[@fondupot]

Should work fine on your Sierra too.

[@albertgavieres7852]

Just did this on a 2017 sierra. All sounds gone. Its like a new truck!

[@fondupot]

Giddy up! Glad it worked.

[@pedroenns7988]

good afternoon hey oh what to grease them or not?

[@fondupot]

Grease only lasts for a while. The rubber pads will last forever.

[@pedroenns7988]

ok but the rubbers have to be greased to install them or not?

[@fondupot]

Nope.

[@Eagle_1985]

I just squeezed some hot glue gun glue in-between the gaps of the leafs and it totally worked 100% …. If it fails down the road just do it again

[@18maaxx_74]

i have a 2018 gmc sierra z71 4x4 on a 2/4 drop and mine is squeaking from the leaf springs and i just placed a order on one of these kits i’ll update yall 🤘🏽

[@fondupot]

Right on. Look forward to hearing your experience.

[@18maaxx_74]

@@fondupot Package got here and i struggled on one because my exhaust was in the way “ i have a after market exhaust” once i got that one done the rest of the three was easy! dropped the truck and jumped on the back, no squeak! letss goo im happy asf thanks bro 🙏🏽

[@fondupot]

Awesome to hear.

[@jason9igallagher528]

Can't find the site to order!

[@fondupot]

Check the video description. www.spring-things.com

[@kevintoledo9958]

Bought these and they didn't work and I doubt I did it wrong but I'm open to suggestions.

[@fondupot]

Hmm. Your leaf pack may be looser than normal. Try giving your U-bolts a tightening and check your shock mounts too. Keep in mind, these pads wont remove 100% of the leaf pack noise, but it should reduce it significantly.

[@kevintoledo9958]

I'll for sure be doing this soon. Thanks you!

[@fondupot]

Glad to help.

[@jairorodriguez3546]

These used to be 30😭 any discount code to buy some?

[@fondupot]

Why do they cost now? Sorry, I don’t have any codes.

[@Toxicwolf61]

How much of a noise reduction did it do

[@fondupot]

A good 75-85% reduction in noise. Much better to be honest.

[@marineinneed]

I got 100% worth every penny

[@RyanHarvill]

Mine went from annoying to almost none existent. It felt like I was riding on air suspension pulling out of my drive way without he clunking for the first time in my BRAND NEW 2023 Silverado custom.

[@spring-thingllc8342]

These will fit other vehicles! I designed them for GM full size trucks because that's what I own but it will work on any vehicle that has 2.5" wide or wider leaf springs. I guess some toyota and ford owners are having similar problems but I haven't been able to check on how wide their springs are yet. If anyone can post that info I would appreciate it! Thanks!

[@Mr.Beastforpresident]

This is for squeak correct? How about the low speed thunk? Any word on how to fix that?

[@spring-thingllc8342]

@@Mr.Beastforpresident It also fixes that clunking sound coming from spring slap.

[@lg740xx]

Did you see the word safely is spelled wrong in the instructions?

[@fondupot]

I didn’t. Nice catch. I’ll let them know!

[@spring-thingllc8342]

omg.... I'm ocd so I'm not sure how I missed that! It has been bugging me since I read your comment last night. facepalm :(

[@fondupot]

@@spring-thingllc8342 I was going to email you this morning! Glad you saw this. Don't worry, I have plenty of spelling mistakes in my videos, lol.

[@CentralCanada]

Months ago following your advice, sent them an email, including yr/model of GMC truck. Asking them if they had a distributor or vendor in Canada. If not, do they sell the product to Canadian clients (street addresses) directly. Also if so do would they ship via USPS regular international parcel post. We don't need to pay for pricey expedited since all international parcel post gets on a plane. Not a stagecoach :-) Never received a reply ! Not even a tap reply to say received to at least indicate they would do research when time permitted. ;-)

[@CentralCanada]

Rockinbr 1 second ago So have bought a couple feet of material to make my own, to try out the concept

[@fondupot]

Hmm. Sorry to hear that. You can make them yourself out of thick rubber. Good luck!

[@CentralCanada]

And noting Top/Bottom locations of the original pads, thinking of 4 units per side. Presently planning to install the top 2 per side, during a op' timeline for a all-pts.' Timbren products install. Will be utilizing for the first time my recent purchase of a "Torin/BR' combo package (hydraulic jack,2 stands & 'red creeper). On sale of course ! :-) .... '96 Sierra sle k1500 8-)

[@David-qw2iv]

So it only works for GM trucks?

[@fondupot]

Should work for pretty much any truck with leaf springs.

[@David-qw2iv]

@@fondupot i don’t get how brand new leafs and bushings can make all this noise

[@fondupot]

Piss poor engineering

[@ChrisHyde]

Hey can you post the dimensions of the spring things? I can easily create these myself :-)

[@fondupot]

Make them as wide as your leafs. And about 4” long.

[@ChrisHyde]

@@fondupot Thank you!

[@mohammedall8668]

So after two years how’s your feedback?

[@fondupot]

Been fine.

[@mohammedall8668]

@@fondupot great ! Ordered it yesterday

[@bradvincet1848]

Is this product approved by vehicle manufacturers?

[@fondupot]

I doubt it since it’s an aftermarket fix. But it’s not hurting anything.

[@redneck4200000]

Why the hell can’t warranty do this? It’s so simple and it would cost them next to nothing especially on a 45k$ truck

[@fondupot]

Who knows.

[@johncherry2096]

John Fix

[@fondupot]

Good John.

[@St.Bowtie]

why does no one show the noise it makes

[@fondupot]

It’s a clunk. Can’t miss it

[@St.Bowtie]

@@fondupot there is a million clunk sounds. It would’ve been helpful to hear the noise before fixing it is all I am saying but other than that thanks for the video.

[@fondupot]

@@St.Bowtie found this video in 30 seconds of searching. kzbin.info/www/bejne/g4PQmI2jopl4aNk

[@St.Bowtie]

@@fondupot yes I already found it. just telling you how to improve the videos as a viewer.

[@fondupot]

@@St.Bowtie Thanks.

[@bigred3336]

Funny you said a 30 yr old truck. Mine is 30 and squeaks like a old mattress on prom night

[@fondupot]

Lol

[@Jacob-pr5cd]

I have a new 2021 Sierra with this problem. So stupid GM can't fix this. Maybe they should just license from this company and put this on from the factory!

[@gabrahamlinco1n962]

Not to be nosy but if you really want to reduce some extra noise on your GM I’d replace your factory bump stops with Timbrens. Really does make a world of difference for ride and noise with the spring-things as well

[@Jacob-pr5cd]

@@gabrahamlinco1n962 I already put the spring things on them and it is quiet now. It's the bad between the top two springs when they rub side to side.

[@claytonb2545]

It’s sad you have to install these. Good ol gm engineering

[@aaroncupples344]

Better than having a death wobble every 25k miles

[@Day-dreamer488]

Why the gm product is bad? Why such things could happen?

[@fondupot]

Happens on every make and model truck I’ve owned.

[@Day-dreamer488]

@fondupot at 7k miles? I ordered. Hope it fixes it. There is the leaf spring issue but also sounds like something in the bed is broken I'm not sure like rolling rocks in bed...there is none ofc

[@fondupot]

@@Day-dreamer488 hmm strange. Maybe something else going on. Like a bad bushing

[@snakeryanmaster]

I just installed my spring things a while ago and went for a test drive. Most of the noises I was hearing went away. I still have another noise, not sure what that it is, might be a brake line or something rattling underneath, but the spring things are a good investment, easy to install, and do the job. Seems like a smoother ride too.

[@fondupot]

Good to hear they helped. Hopefully you can figure out your other noise.

[@snakeryanmaster]

@@fondupot I think the springs need to be replaced. 15 yr old truck, and I cant find anything lose anywhere. Gotta be the springs. Pads stop some of the noise, and If I put lithium grease in between the springs, it settles down, but you can see where they are buckling and rubbing, I think next year or maybe this year I will find some new ones? No any good mfgs? These were mfg in mexico, probably along with the truck. hehehaha

[@fondupot]

Could be. They might also need a good power washing and then lube them up with grease. Could have some rocks and dirt between the springs.

[@snakeryanmaster]

@@fondupot Living in Oklahoma here. Weather getting warmer, I did spray some lithium grease a little bit, with the warmer weather, the noise goes away, and early in the morning it returns, I think your assessment is correct. One of these warm or hot weekend days, I will scrub them down and then spray grease in there. I might modify them with some brackets to keep them tighter. Ive seen so many ideas on here, lots of things to try.

[@fondupot]

Could be the bushings going bad. And as they warm up the noise goes away. But when their cold they squeak.

[@jasun6859]

$45 when you can make your own for $4

[@fondupot]

Be my guest. No one forcing you. Not everyone is as handy as you. Some folks might want a pre-made solution that works. Cheers!