How To Fix P0740 1998 to 2002 Accord 4 cylinder Model

[@jacobsahagon1646]

I’m getting the part right now. Work the magic myself. Ima use the pointers appreciate this feedback

[@dougmontgomery5700]

Your disassembly tips & guidance were very helpful. Thanks for taking the time to make this video.

[@BulletSolano]

No problem

[@dylanpipkins]

Hey man, thank you so much! I'm going to try this now.

[@Whi7ey]

I’m doing this now and that last bolt I was stumped until you showed the 17 and 10mm. Thank you ! Do you have a linear shift solenoid video and I’ll have replaced all 4 before a 3x3 drain and fill.

[@BulletSolano]

I don’t

[@jerrynavarro2404]

Ohh NO I had that same problem on my 98 accord automatic transmission it messed up and ever since then I drive stick 5 speed manual is better made.

[@30cjbeast]

Did you have trouble putting the transmission screw back in? I cannot get it to go in.

[@jodyjoe21]

If replacing the solenoid isn’t the problem, what do you think would be the next step?

[@BulletSolano]

Low transmission fluid level Dirty transmission fluid Faulty torque converter clutch solenoid valve Torque converter clutch solenoid valve harness is open or shorted Torque converter clutch solenoid valve circuit poor electrical connection

[@philskeez]

Man this was such a great video thank you so much for doing this🙌

[@dicksonpirtheesingh5032]

Hi ..On the dual linear solenoid. What is the bolt on the side used for? I was having rough shifting for first to second gear and purchased a new one on Ebay. This made the problem WORST and I had to put back on the old unit. I have googled and read that the solenoid can be adjusted but they didn't explain. On further search it is said that to insert a pentagon adjustment tool into switch A and turn 1/8 to 1/4 clockwise and then the same to be done to switch B but COUNTER clockwise. An help on this? I am thinking maybe the new switch needs a bit of adjustment

[@SamuelLanghorn]

on an Accord 2001, 4 cyl, I followed your instructions and replaced the AB solenoid. Problem is still there (i think it got worse), I am getting P0700, P0740 and P0780. should I disassemble all solenoids (C + D and the linear double solenoid)? I don't know how to test them when still mounted? I can't get my multimeter contacts inserted for a decent resistor reading (which might not be enough anyway). your comments are most appreciated. I noticed that you kindly pretty much respond to everyone with a question.

[@BulletSolano]

If those solenoids didn’t fix it yes check or replaced the linear solenoid and C-D solenoids I have a video on how to check them at least one way kzbin.info/www/bejne/aGm2YYWAl9SiqtU

[@SamuelLanghorn]

@@BulletSolano Thanks a lot for your quick response and the nice video replacing the lower solenoids...... lets see how it goes 🙂

[@ElementFreedive]

Hello I tried it and cleaned the screens! Do you know which soleniod is for the 2nd to 3rd gear shifting?

[@BulletSolano]

www.hondaaccordforum.com/forum/general-tech-help-7/shift-solenoid-identification-2000-accord-2-3-a-45986/

[@Mgh101590]

Hey bullet hope you read this got code p0740 and p0700 replaced the solenoid now my car doesn't engage and now I have code p0730 is my transmission done. The night before I changed the solenoid it was running perfect and after replacing it , it doesn't run anymore it's like it's in neutral I went back to the old solenoid but it's the same thing it doesn't engage any gears what can be wrong I'm hoping I don't need a transmission

[@BulletSolano]

hey bro, sorry but your transmission is done

[@SunshineCarpetCleaning]

A few weeks ago my cruise control stopped working. Today my check engine light came on. I found out it’s the same solenoid you are speaking about. Is it possible that once I replace the solenoid the cruise control will start to work again? I already checked the fuses for the cruise control and fuses look good.

[@BulletSolano]

Brake pedal switch

[@SunshineCarpetCleaning]

@@BulletSolano Would a faulty brake pedal switch cause the cruise control button to lose power though? The cruise control button green light doesn’t even come on.

[@BulletSolano]

Yes

[@SunshineCarpetCleaning]

Hey brother ever since I replaced the torque converter clutch solenoid my car has been having idling problems. What do you think could be causing this is it possible it’s a bad part I got it from AutoZone.

[@zachgrime6841]

hey bullet your videos help alot but i got a question, I DONT KNOW WHAT IS WRONG OR IF MY TRANNY IS SLIPPING!!!! I got a code reading saying P0700,P0740,P0730! can you help and tel me what you would start doing first?

[@BulletSolano]

Hey man, I don’t know what car do you have but if it is a Honda Accord the transmission is done

[@FUBuddy]

my 99 accord 2.3 is slipping when hot, ive replaced fluid and all of the externals except the neutral safety switch and the tcm. gave me codes p0700 and p0740 once, but has not come back. still slips tho. any ideas other than replacing transmission ?

[@BulletSolano]

Your transmission is done

[@daviddelgado475]

Brother please help me, I did everything you said, and the solenoid is in. The problem is getting that 17inch bolt back in where the transmission fluid is, I tighten it and it leaks! I cant get it to go in, thats the bracket that you have to move out of the way. I noticed it has a a metal o-ring on the bottom and one on the bolt. Why won't it screw down? I only have one hand , my left, so it's hard please help if you can, thank you! I use the right wqrist but the screw doesn't seal and when I crank the car transmission fluid leaks out!

[@BulletSolano]

It’s a banjo bolt, it has copper o-ring on both sides

[@edwingeorge9097]

Was the old solenoid spoiled? Did you test the old solenoid?

[@lililililililil-7814]

Having this issue after installing a low mileage jdm transmission worked the first couple days now I got the d4 light flashing and got this code what should I do are the jdm trans suppose to work or what do I do???

[@BulletSolano]

I hope you have warranty on that transmission, sounds like bad transmission to me

[@lililililililil-7814]

@@BulletSolano the transmission worked fine the first couple drives I bought one with 40-60k miles, but just the other day I was getting on the freeway and the car jerked slightly then my check engine light came on still drove fine got it scanned and got codes p0740 on the jdm trans so I got some new solenoids for it hopefully it helps cause ppl saying u need to put us on jdm

[@lililililililil-7814]

the usdm shift solenoids on the jdm trans

[@Mrsbristol0514]

I have an 02 Accord 4cyl. For 12 years out shifted rough at times from 1st to 2nd, now it just won't go into second, it tries. Just changed the speed sensor and doing a drain and fill. Was thinking of maybe the 2nd clutch solenoid? Opinion?

[@BulletSolano]

Yes replace that solenoid and do 2 more drain and fill, also scan for codes, if that doesn’t fix your issue the problem is internal

[@Mrsbristol0514]

@@BulletSolano Thanks for the reply. .I need to clarify what part.. I meant the 2nd clutch pressure switch.. is that the correct one? or should I replace the clutch pressure control solenoid? I haven't worked on cars in 20 years.. trying to fix my teen son's car. He's all in for doing the work and learning, I just have to give him guidance. If you could please confirm what part I should actually look into replacing please?

[@BulletSolano]

Yes replace the 2nd clutch pressure switch

[@Mrsbristol0514]

@@BulletSolano thank you.. now to find the part number lol. This car has been so great I am hoping we can save it for a couple of more years at least.

[@charrohernandez6835]

Que hay compa tengo un accord 2002. Cuando lo pongo en Reversa o en D3 el carro como que brinca y truena. Y cuando freno aveses no quiere dar pa delante nomas se escucha el motor. Me dijo el mecánico que es el selonoide sera eso ?

[@piappiaping3106]

Tbh ive solve it, theres a trick, depends because all problem not same. Mine civic ES 1.7 solved by changing just 1 solenoid from 2. 1 solenoid works fine.

[@rezzerectedjsu4843]

Hey salono how's that solenoid handling , I wanna buy the one you got off Amazon but I'm worried I've bought a vtech solenoid off Amazon once and it was faulty and was leaking

[@BulletSolano]

Is good

[@brionadderley1643]

Hey Bro nice video; I got a 70 code which was Automatic Transmission malfunction with the automatic transmission controls; i located all the shift solenoids A,BC cleaned em all then i checked for codes again and it was gone; i started my car and went through all the gears and the delay i was having when i shifted in reverse went away and the other drive gears transitioned smoothly; all of my mounts were bad so i replaced them; but although im getting no more transmission codes when i put my car in drive either it be d2/3/4 its slipping when i accelerate and jumpin; now ive good a few other codes which may coincide with this problem such as Tank pressure sensor and o2 primary sensor but can u help ? Good content btw !! Keep up the work.

[@BulletSolano]

Let me see what I can do

[@brionadderley1643]

@@BulletSolano hey bro do you still have the old solenoid and could you tell me if both solenoids were clicking and the resistance on them ?

[@shadyGuy-r1p]

hey bullet i have the exact same car but it makes a noise when its sits in park and neutral and jumps when i change from park to drive and so on there isnt any lights on but i think i just need a trans fluid change and clean the solenoid

[@BulletSolano]

Hey man, that noise is your torque converter! Your transmission is done

[@shadyGuy-r1p]

@@BulletSolano never mind I was wrong it only jumps when I put into drive mostly d3

[@shadyGuy-r1p]

@@BulletSolano what do you think it is? Since it only jumps when I put into d3

[@BulletSolano]

Probably d3 is bad in the transmission or motor mounts

[@shadyGuy-r1p]

@@BulletSolano transmission was changed with a refurbished my cousin said the motor mounts were cheap and needed replaced I think ima go with that one

[@stephenthomas5214]

What’s the bolt called you removed at (2:36) ish.. I can’t find a replacement for it because I accidentally over torqued and now it doesn’t tighten and leaking transmission fluid

[@BulletSolano]

Transmisión line banjo bolt

[@stephenthomas5214]

You possibly have a link? And thanks

[@BulletSolano]

I can’t found it anywhere!! Dealer or junkyard is the best way

[@dylanlarson1071]

Mine free revs into every gear and if i shift it manually i have to wait about 4 seconds until i feel it engage and then i am good to go. Think this could fix?

[@dylanlarson1071]

I also do have this code

[@BulletSolano]

Most likely your problem is internal

[@dylanlarson1071]

@@BulletSolano i went out to start it today and everything was normal? Took it on a 10 minute drive. Maybe it acted up because i was in traffic for a while and it got overheated?

[@jorgeluna6191]

Hey there Bullet. My 1999 honda accord does not let me rev higher than 3000 rpms. It starts sputtering. I just put a new distributor and EGR valve because I had a P401 code and plus the car would suddenly just turn off while driving. So the car no longer turns off while driving at all but now I can't go passed 3000 rpms.. please help me!! Gracias!!

[@BulletSolano]

Hey man, you need to replace the vtec solenoid, sometimes low oil or dirty vtec solenoid do that! kzbin.info/www/bejne/kGi5iYyHbrF7l9E

[@tavvybaphadili2728]

this code popped up on my 98 accord 4 cyl and when it first came on my car would rev high then jerk back and forth a little while not accelerating then when it almost red lines it shifts into gear and goes. but now when i accelerate i loose complete power and the car kinda just rolls when i press on the gas then jerks around and goes (sometimes) then does it again. you think changing the solenoid would fix the problem or is it time for a new trans?

[@tavvybaphadili2728]

also the code P0420 came up and i know its an exhaust issue but i was wondering if that could possibly play a role in the reason why my car cuts power

[@BulletSolano]

Yeah, it cuts power for that p0420 and replace this sensor and transmission fluid, if that doesn’t fixed it is new transmission time

[@tavvybaphadili2728]

@@BulletSolano will try it out, thank you!

[@BulletSolano]

No problem

[@noemah3272]

I've been having problems the past 6 months where my first revs high and then shifts into second a couple days ago I've done the drain and fill three times it. shifts a whole lot better but still revs a little bit and then shifts into second what do you think could be the problem? I've added the lube guard red and the shudder fix..

[@BulletSolano]

Torque converter probably is going bad

[@noemah3272]

@@BulletSolano how could I prolong the torque converter? And is it hard to replace?

[@BulletSolano]

Transmisión need to be out, is just matter of time

[@kingdo657]

do you recomend BLUE DRIVER obd2 on these 98-02 accords.

[@BulletSolano]

Never used it before but reviews said that is ok for the accords

[@alonsosmobileautorepair8862]

I have it and I like it

[@RoloGaming5411]

Yes they work great I've been using my bluedriver on many makes and models from chevys, fords, acuras, Toyota, honda, and Mitsubishi they work with many other manufacturers. But yes it definitely works on ur 98-02 honda. I have my immobilizer deleted and still can read codes with my bluedricer best 100 dollars I spent on a Bluetooth scanner lol!

[@nicolecato634]

This is under the intake ?

[@GF-mf7ml]

A&B is 1st and 2nd gear?

[@charlesknowles7789]

Does anyone know where the camshaft position sensor is on a 4 cylinder 2000 Honda Accord?

[@j_S0VEREIGN]

I have the same vehicle and my transmission is shifting hard. I wanna clean these solenoid first.

[@lowiecantgreen9496]

my 01 accord 4 cylinder slams into gear and just gave me this same error today. whats the first thing i should try?? changing the solonoid like you did? any help would be appreciated thanks!

[@BulletSolano]

Change the solenoid and replace the transmission fluid

[@lowiecantgreen9496]

@@BulletSolano ok thankyou very much!

[@lowiecantgreen9496]

@@BulletSolano do you know where i can buy the part original? and also which is the solenoid i have to change? thanks again!

[@BulletSolano]

Go to any dealer and replace the one on this video

[@lowiecantgreen9496]

@@BulletSolano ok thankyou very much for your help and keep doing what your doing!💪🏽

[@Toast.420]

Mine wasn’t even bolted down properly seems like somebody did it on purpose when they put it back together didn’t screw in the layered plates

[@MustangGuy1996]

Hey man do you know how to replace the shift B solenoid? If you could make a video i’d really appreciate you and i’m sure many others would too. There are literally 0 videos on KZbin at the moment explaining how to do this

[@BulletSolano]

No problem, I’ll put it on the list

[@Geko916]

I am having the same issue, even though am accelerating the car takes a little while to respond, as soon as the car warms up the car is fine. But i am still having the same code

[@takethedamnphoto]

hey bullet, i have the same car 98 4cyl. I have P1738 and P0740. I know my transmission is going out, just took it to a tranny shop and quoted me $3k to fix it. You think I should try replacing the solenoids and see if that helps? The car runs fine, but shifting through 1 and 2 gets all jumpy. Also reverse too. Also makes a noise when idling

[@BulletSolano]

Hey, yes replace pressure switch and A B solenoids, transmission fluid as well

[@takethedamnphoto]

@@BulletSolano Do you think changing the transmission fluid can cause more trouble?

[@takethedamnphoto]

@@BulletSolano Also, does this mean I won't have to replace the entire transmission with a new one or a rebuilt one?

[@BulletSolano]

It could wet worse

[@BulletSolano]

This process probably is going to fix your problem but sometimes is not, if this doesn’t work your next step is new transmission

[@LRA7393]

I changed this solenoid now my car makes a squeaky noise when it reverses or when i turn would you know what would cause it?

[@BulletSolano]

Coming from where? Lower ball joints probably

[@LRA7393]

@@BulletSolano not sure at all

[@Ezeke_]

My car has almost the same problem but when it shifts 1st and 2nd it like jumps in to gear but theres no d4 blinking or check engine light , like a year ago i had got the same code for the torque converter but it took off but idk if maybe by changing the sensor will work?

[@BulletSolano]

Probably with new sensor and new transmission fluid

[@Ezeke_]

Ok thanks bro hopefully it helps 👌🏽

[@BulletSolano]

No problem

[@fabianlara9099]

Did you solve the problem?? @Ezequiel Gonzalez

[@Ezeke_]

@@fabianlara9099 I still haven’t had the chance to do it but I cleaned the old one out and its still the same so ima have to order a new one

[@aprilhall4075]

Hey me again. So now I have a linear solenoid problem. The code is 1768 but I'm having problems finding exactly where this particular solenoid is as there are several in the car. Can you please help again?

[@BulletSolano]

Hello, that’s the solenoid from this video, replace it and replace the transmission fluid, if that doesn’t help probably the transmission is done

[@aprilhall4075]

@@BulletSolano Thank you

[@BulletSolano]

My pleasure

[@alejandomedina]

do you have the part number for that selenoid ? they cant find it at the store

[@BulletSolano]

I don’t but this is the part amzn.to/2UkBaRM

[@tylerc7482]

Is that the original instrument cluster if not where did you get that one

[@BulletSolano]

Is not, I get it on eBay

[@charlesknowles7789]

I have a 2000 Accord 4 cylinder that was accelerating slow and won’t rev past 3,000 rpm, it has a check engine light. Already replaced all the transmission solenoids, transmission fluid, serviced it, replaced the injectors and pump, map, throttle and idle sensors.. it has power now but still won’t go pass 3000 I suspect the crankshaft sensor but I’m not sure, I would change it but idk how to remove the pulley bolt. Me nor any mechanic could find the Obd 2 port, any suggestions?

[@BulletSolano]

Replace the vtec solenoid

[@charlesknowles7789]

@@BulletSolano yea I didn’t replace that neither, I’ll try it

[@vgaram201]

Hey bullet solano where u buy that part. Is it oem or after market

[@BulletSolano]

From amazon, link is in the description

[@vgaram201]

👍

[@h22eh6]

2001 Honda accord. My code says P0740 circuit malfunction. Your code said p0740 circuit open. I have clean fluid and trans shifts better than my new Honda no problem no slipping. Swapped multiple solenoids. I don’t know what to do

[@BulletSolano]

Did you check the conector to the solenoid?

[@h22eh6]

@@BulletSolano i did pins seem tight but I think it’s a electrical problem

[@redboi6064]

Where did you get the solenoid from?

[@BulletSolano]

Amazon probably

[@eduardocaspermontes]

Where did u get the part for it?

[@BulletSolano]

Autozone

[@robertcarlos78]

Is that a after market solenoid

[@BulletSolano]

Yes

[@danielnavarro9247]

Do you remember if you had to clear th code or did the light turn off itself?

[@BulletSolano]

I always clear the codes

[@danielnavarro9247]

Thanks for getting back to me 👍

[@black7579]

Where is it located on a v6 transmission?

[@BulletSolano]

Under the intake tube

[@hiramalonso97]

Would you happen to know how to fix codes p0700, p1739, p1751?

[@BulletSolano]

P0700!! Check fluid level, probably dirty, or bad shift solenoid. P1739, replace 3rd clutch pressure switch P1751. Replace shift solenoid valve B

[@Sndprz90]

Amigo mi accord cuando hace los cambios golpea y otras veces los hace suave y funciona excelente, podrias ayudarme en q puede ser?

[@BulletSolano]

Remplaza el pressure switch y los A y B solenoids

[@Sndprz90]

@@BulletSolano cual es es pressure switch ? Los otros si se cuales son gracias x atender

[@ladylisa3490]

My accord is in limp mode i can't get it past 3000rpm she idles fine but idk an nothing shows up on the dash board Can someone please point me in the right direction

[@BulletSolano]

Low on oil or vtec solenoid needs to be replaced kzbin.info/www/bejne/kGi5iYyHbrF7l9E

[@ludinvalencia8517]

im hoping mine is this issue

[@gilbertgarcia4370]

Is there anyway to test this part before you put it on my brother?

[@BulletSolano]

Get a multimeter and check for resistance

[@briankim4519]

what is that solenoid for?

[@BulletSolano]

It controls the torque converter clutch

[@LoveAnimeBigFan]

What if my Honda Accord 2002 only jerk when reversing

[@BulletSolano]

Motor mount

[@LoveAnimeBigFan]

@@BulletSolano thank

[@LoveAnimeBigFan]

Which one do I exactly have to replace? Do I replace all of them

[@BulletSolano]

Rear one

[@LoveAnimeBigFan]

@@BulletSolano thank bullet got the rear motor mount replace and it 100% better now I have to replace the front one because it gone bad. Car idles 100% better when I get the front one replaced it will be 200% times better

[@mac9018]

Working on my fucking car for hours and I don’t have all the tools.. 😂😂

[@JayZTupacNas]

Hey Bullet! Thanks for all the videos you are doing for the 98-2002 Accord. It is helping me learn a lot about cars. We all appreciate you. At 5:05, what is the screen for the radio that you installed to replaced the radio stereo? kzbin.info/www/bejne/d2qUf6SsrbRliJI -- I saw your video that you removed the Honda Accord Radio Stereo. I couldn't find any videos of you installing that. By any chance, do you have a video of installing that product? Also, what brand is that? I was looking into getting the Double Din 7 inch screen. Thank you!

[@BulletSolano]

Hey man thanks, I didn’t found anything to fit the stereo, but you can find that kit at Walmart or autozone

[@gilbertgarcia4370]

Also how long did this part last you?

[@BulletSolano]

Is been there for 7 years

[@gilbertgarcia4370]

Thank you so much my friend and this is the part that you mentioned on the Amazon link?

[@BulletSolano]

Yes

[@anisdabbous5581]

Hello I have a Honda Accord 98 Many times the D4 does not work, so I have to shift to D3 or 1 then move it back to D4, what do you suppose is the problem? Thanks

[@BulletSolano]

Replace fluid with Honda fluid, replace pressure switch, if that doesn’t help you need a new transmission

[@DA-mw6gh]

Do you know the part # ?

[@BulletSolano]

Link is in the description

[@TriggerR200]

Hey bullet I changed mine and now my car accelerates slow and the D4 be flashing

[@BulletSolano]

Put an OEM one