#BulletSolano

Hi guys and thanks for watching, in this video the replace on the VTEC Solenoid valve is simple but time consuming because I don't have space to work but for me is the best way so I don't have to remove the housing for the thermostat.
amzn.to/2Mj16EZ Vtec Solenoid Valve
amzn.to/2WlTx50 Impact Gun
amzn.to/2sDIMNQ Vtec Solenoid Gasket
Gratitude www.paypal.me/bullet23
amzn.to/2AUdEOl Throttle Body Cleaner
amzn.to/2DmiLsd 10 MM Wrench
I buy the gaskets on Ebay but they are Honda not aftermarket and I hope this video help you to replace the valve if is bad or just to clean it and if you have and oil leak this is how you fix it.
And before you put everything in the car make sure your valve works, just get the valve in the negative of the battery and run a wire to the positive side of the battery and put it in the connector so you make sure your valve works.
Thanks again guys for subscribe and support the channel.
------------------------------------FOLLOW ME---------------------------
Follow me on Instagram
@bulletsolano36
Follow me on Twitter
@bulletsolano
Like my Facebook page
/ luis.b.solano.3
Thanks for watching.

[@ianpence1697]

I just got a 2000 Honda Accord SE. You have become my go to guy for menachical work videos. Thank you.

[@BulletSolano]

Thanks

[@martincontreras6031]

Where is the VVT 3.0 Honda Accord EX 2000 V6 located?

[@BulletSolano]

On top of the oil filter housing

[@jacko-13]

Thank you Bullet Solano. This video was extremely helpful. I followed the guidance to replace the gaskets in my Honda Accord EX 2002 over the weekend. I took your tip and made a very small wrench by snapping off one side and grinding the broken end smooth on a bench grinder. One tip though: my ring wrench didn't fit over the top nut and I actually had to grind away on the ring to make is slimmer. After about 5 grind/check fit cycles, I ended up making it so it could slip over. After that the rest was easy. Thanks again! Really enjoy your videos.

[@mosessanchez8253]

Thank you for taking time in the past to show us how to take care of your 6th gen (2002)

[@Ariztid]

I could not figure out where the leak on my dad's Accord was coming from, but I came across this video. It was a pain to get those bolts out but I got the job done. Thanks for sharing this, Bullet.

[@BulletSolano]

No problem

[@aaron123112]

Man so many of your videos have saved my ass!!! Thanks for taking the time to teach all of us!!!

[@KreationsOvMatt]

Doing this on my wife’s car this coming weekend. This is my tutorial. Thanks for the in-depth video. Wish me luck!

[@BulletSolano]

Good luck

[@azweaver9600]

Thanks for the video, I used it as a guide to replace my gasket. I did one thing differently, I also removed the oil pressure sensor from the spooler. Once that was done I was able to access the bottom bolt with easily with an offset wrench. Thanks again.

[@BulletSolano]

No problem

[@ddeltiempo]

Just replaced this whole VTEC solenoid, got a brand new one for $30 on eBay. Followed this video, excellent instructions. USE BOX-HEAD WRENCHES they will make your life a lot easier. Thanks for the video!

[@BulletSolano]

No problem

[@AngelSanchez-ig3jt]

I kept thinking that my valve cover was bad. I've changed it twice in the last 2 years but it would always leak from the back side. Now I'm starting to think it's this solenoid. Thanks for the video.

[@BulletSolano]

No problem

[@SuperChad1313]

Dude......thanks for covering everything. You win the Internet today.

[@BulletSolano]

No problem bro, thanks

[@takethedamnphoto]

Thank you man! Just waiting for parts and using this video to do it myself. Probably a $500 job at the shop!

[@BulletSolano]

No problem

[@bidsanand]

Awesome video, really like the way you explain. Did my vtec replacement. Would like to give a small tip, to remove the third bolt under the valve I developed a technique, attached pics to explain. Just in case someone feels difficulty in getting to it, i guess it’s called buddy wrench technique. And don’t even try the bolt without a small 10mm wrench. Cheers..

[@arielban1]

Thanks for the video Bullet.. I was able to perform this procedure easily. I followed your video, but I used the Harbor Freight Box End off set wrench 8 pc item 32042. This enabled be to get the bottom bolt off. I had to wiggle and work the wrench as it was tight, but the nut eventually came loose. I also cleaned the EGR since I had to remove it for the VTEC gasket replacement. In addition, I tested the VTEC solenoid per your instructions.. That was excellent testing procedure. I learned something... thanks again.

[@BulletSolano]

Great and thanks for the advice on the wrench

[@anthonys.2552]

My mechanic quoted me $600 to replace this. I am thankful I found this video now !

[@BulletSolano]

No problem, It’s not easy process but $600 is crazy

[@BulletSolano]

Here is one more just in case kzbin.info/www/bejne/jpCUfWh8qsR7ac0

[@carroll6]

my questioned was answered after watching just a little while.

[@melbourneman1178]

great vid!. love your clean engine bay! my o rings may have been leaking for years. its dirty on that side of the engine, will clean today. shes gettin old with 264,000 miles!

[@BulletSolano]

Thanks

[@michaellindsey31]

YOU MAKE EVERYTHING SEEM SO EASY GOOD JOB 👍

[@BulletSolano]

Thanks

[@Hachiro]

To viewers: Make sure to not lose the spring that holds the plunger in place. I dropped mine without noticing, and it made the car go into limp mode. Rewatched Bullet's video, found the spring, and once I installed it, the car ran fine again xD

[@robertosaldateii5691]

This is a great video man. Might buy one of these that needs a solenoid replaced. Will come back around to let you know how it goes!

[@StreetMisfit]

Very good video. I enjoy your work because it’s very thorough and recorded well. It is difficult to find great quality work. Keep it up 👍🏽

[@BulletSolano]

Thanks bud

[@roberey6821]

Excellent videos from these guy good job.

[@Julian-zy1em]

My transmission is acting kinda funny.. almost like the VTech takes a second to engage. My brother told me this was the problem, it happened to him. Once again thanks for another great video!!!

[@BulletSolano]

No problem

[@user-ib8rg7vn8c]

Absolutely love your channel

[@dantewilliams2735]

Awesome dude ive been trying to figure out how to get the solenoid off for a week!!! Never thought to take the egr valve off! 😅😂

[@BulletSolano]

No problem bro, thanks

[@dantewilliams2735]

No bro 🙏 thank you

[@matador19700]

Good video , I ll try with my 99 accord , I have that problem now , thanks

[@MrHines88]

I got Honda 2door Coupe EX that im trying fix up so your vids bru is very help learning material

[@BulletSolano]

Thanks bro

[@lilbbbbbbb]

Clean looking engine man thanks for the video

[@BulletSolano]

Thanks, No problem

[@jamesc6945]

Just did mine on my accord, what a difference. Thx👍🇨🇦 be patient people it does come out, with a few swear words 🤣😂🤣😂🤣

[@mr.luislarios6295]

well done it give me a positive idea how to do my project thank you

[@BulletSolano]

Thanks, no problem

[@dougallen3478]

Thank you for your comment , So tell me why do you think that seal would start leaking that bad ? And i`m gonna believe that the motor has to come out to do this , Correct ? Also how can I be sure that`s where the oil is coming from ? I just got done hosing the whole engine the best I could with some degreaser , Gonna let it set till morning , Then hit it with the water hose . Again thank you for your help and keep up the good work on your videos , They have been very helpful in me repairing my car .

[@BulletSolano]

Thanks man, tomorrow clean the engine from the bottom and check in between the engine and the transmission is you see oil around that area then you have a bad rear main seal, and the transmission has to come out to do the rear mail seal

[@dougallen3478]

One more thing I forgot today I pulled all 4 plugs and all were burning like brand new completely dry car runs great just can`t find bad oil leak

[@mikeokay3237]

Hey bro your valve cover gasket replacement video helped me , and yet again this video helped me out also thank you for making these you helped me out so much I really appreciate you making them

[@BulletSolano]

No problem bro thanks

[@Gandoff2000]

My wife's 1999 honda accord was leaking 3 quarts in 100 miles (on the passenger side of the car)! I could not see where it was coming from. Changed the distributor O-ring, still leaked. replaced the VTEC to head gasket but it did not look bad. Replaced the gasket under the solenoid. The leak stopped. The gasket under the solenoid was brittle and I suspect leaking. Getting those three bolts for the VTEC to head broken lose was not easy. I used a 10mm boxed in wrench and some uncool methods to get enough leverage on the wrench to get the bottom one lose. (included a hammer, a hatchet and a crowbar). Taking the water inlet off would have made it a lot easier but I did not have the "O" rings and gaskets for it and having to catch the coolant would have been a pain. One more thing, I replaced the PCV valve. A bad one can make seals fail. Thank you for the video!

[@BulletSolano]

+Gandoff2000 ok cool, and yes ti remove those 3 bolts is not a fun job but I have the same experience

[@williameldon8768]

Thanks for the informative comment. Did you have any symptoms of failing VTEC solenoid or just leaking oil? Thanks

[@BulletSolano]

+William Eldon thanks Bro. No problems with my solenoid just leaking oil

[@Gandoff2000]

William Eldon on mine, yes, everytime the oil got low, the engine light came on with a 1259 code which indicates a problem with the vtec. But that went away after the leak was fixed.

[@arielban1]

thanks gandoff for your detailed experience

[@chasemiller7974]

Badass looking motor.

[@BulletSolano]

Thanks

[@farshadnikzat8571]

GREAT JOB

[@jluc155]

Awesome bro .... thanks for the video

[@BulletSolano]

No problem, thanks

[@lebronjordan802]

Great video 👍!

[@BulletSolano]

Thanks

[@EGLALGEXLAJOSEPHS]

Thank you Bullet...

[@BulletSolano]

My pleasure

[@ianpenn3366]

I use a 1/4 ratchet to loose the two nuts on top And a 10mm combo wrench for the bottom

[@JessicaNavas5713]

Laparascopic precision as always, avoiding unneccessarily cracking open gaskets and you found access without even taking out your air intake. Impressive. Do I need to cut my 10mm in half to do it? I have a small one, but I guess I will see.

[@BulletSolano]

Probably you have to

[@Unknown90010]

good video now i know how to change that you helped me change my thermostat on my car that was made easy can you do a video on how to change the transmission solenoids on that same year honda accord i have a 2000 and i just wanted to know how to do it thanks

[@BulletSolano]

Ok no problem

[@jorgemunoz4986]

Very good video man

[@BulletSolano]

Thanks

[@mjaye6042]

Thank you!

[@BulletSolano]

No problem

[@myronblack8852]

hey i have a 98 accord torneo with a F20b single cam engine. i always y thought vtec was the solnoid only till i watched your vid, ten thumbs up for clarity bro. Whats puzzling me is that my vtec does not have a sensor attached to it only the solnoid. IDK what to think coz now every vid or pic i see of a vtec it has the sensor attached...

[@BulletSolano]

I think your engine vtec is control with oil pressure only that’s why

[@Really658]

My man!

[@christopherrollandwilkins6298]

Man I see you customize A Honda accord that's cool as hell I have a 2000 and its leaking oil so thank you for the info on finding and fixing. And big ??? "how much did you spend on the customize work on the engine".

[@BulletSolano]

Thanks man, I have this car for 7 years now and I think in the engine is only like $1000 but the money in this car is on the suspension and brakes!! Probably all the car including labor I spend around $7000 maybe more

[@IvanRom100]

Hey man! Love your videos..always very helpful...I have a question. I have a p1259 code on my 2000 accord Ex 4cy 2.3l. Could this mess with the EGR. Says I have insufficient flow even tho I just replaced it

[@BulletSolano]

Hey man, thanks!! Clean the EGR passage

[@Peguerochannel]

Good vídeo

[@BulletSolano]

Thanks

[@ChangedforeverBYHIM-gabe]

I still get the same code and hesitation at high speeds. Can it be something else?

[@koreymayo8884]

I have a feeling this is where my oil is leaking. I already did distributor gasket and valve cover gasket.

[@mr.profezzional6935]

Hi, what gasket ended up being the leaky one?

[@EduardoRodriguez-kk9jc]

Buen video

[@BulletSolano]

Gracias

[@ronniecarlisle2873]

My bolts were very hard to get off . They were over tight , had to make a 10 mm socket and a hand breaker bar to fit lol

[@JorgeHernandez-lz1rb]

Sup bro good job

[@BulletSolano]

Thanks

[@prasannasridevi7387]

Excellent video.. Any recommendations for a good, honest mechanic in Austin areas (TX)? I don’t want to go to big dealers or mechanic chains but prefer one man or two men / family run shops. TIA

[@BulletSolano]

Thanks, sorry I don’t know anyone there

[@codywoodring]

Any tips for getting the lowest of the 3 bolts? Can't seem to get mine unstuck

[@BulletSolano]

You have to pull the wrench with all your strength

[@brittanymarchetta4575]

Quick ? Woke up car didn’t start noticed cam barely spinning and rotor checked timing belt still intact what do you think

[@BulletSolano]

Check your distributor

[@WaldoSolanoOnlineDanceClasses]

esta bueno el video perrito... 👍

[@BulletSolano]

Gracias perrito 🐶

[@dougallen3478]

Hey Bullet ! I have a problem and i`m hoping you may be able to tell me what to do and look for please. I have a 2000 Honda Accord Coupe 2.3 5 Speed . I just recently replaced the head due to valves being bent from timing belts snapped . I have replaced all belts and seals & water pump . I now have a really bad oil leak coming from the back side of the engine and I can`t seem to find where it`s coming from . I`ve already replaced o ring in dist. , I`ve already taken Solenoid apart and cleaned it 2 times and this time I used gasket sealer , i`ve replaced valve cover gasket and all seals in it alsowith gasket sealer on both sides of gasket from cover to head, I`ve already changed oil and filter, only thing I havn`t changed is oil sending switch but it don`t look like it`s leaking . Any help that you can give will be great ! This car is already taken everything I got to repair . Thank You

[@BulletSolano]

Hey man I think the rear main seal is leaking

[@Hawlkeye-e9p]

That red hoze going to the intake? I don't have anything on that port. Its wide open.

[@BulletSolano]

Put a plug in it amzn.to/3sFa5GB

[@twopiecez5226]

Which wire in the plug of solenoid do i need to tap the positive wire from battery??

[@BulletSolano]

It doesn’t matter

[@gfriedman99]

Anybody know if getting to the vtec bolts from underneath is possible? I am just thinking another angle might be easier. One guy had a video where he got it from underneath after taking the oil filter off.

[@BulletSolano]

It’s a possibility but in my accord the oil filter is underneath the intake, i don’t think is possible in my accord

[@mi_so966]

thank you for the video! One question though, on my car only the top is leaking, could I just replace the top one and not have to remove the EGR.

[@BulletSolano]

Yes

[@mi_so966]

@@BulletSolano thanks

[@BulletSolano]

No problem

[@brianscott3128]

So i brought the whole vtech assembly do i still need to loosen the top three bolts to install it?

[@BulletSolano]

No

[@carmenvega126]

Muy buen vídeo!!! Me podrías decir como exactamente puedo pedir los nombres de los dos gasked por favor. Gracias

[@BulletSolano]

Gracias, búscalos así, depende el modelo y año que es tu auto, en mi caso lo pedí así 2000 accord vtec solenoid valve gasket para auto de 4 cilindros

[@BulletSolano]

El mío es este, si el tuyo es igual puedes pedir este gasket Dorman 917-170 Variable Timing Solenoid Gasket www.amazon.com/dp/B00TEFMBFY/ref=cm_sw_r_cp_api_i_NMuFDbS1GR39K

[@carroll6]

Would this be a good time to replace the EGR valve also? What other things might be replaced, or upgraded. Might as well do it all.

[@BulletSolano]

If you have the money go for it, but in my case if is not broken don’t fix it

[@carroll6]

@@BulletSolano these repairs would cost a lot of money from most shops! The EGR valve I saw a quote for $500 to do it. Even though the parts cost money.. I would say replace the thermostat, EGR, along with just a new Solenoid. The car would be good for a long time, as long as you own the car.

[@BulletSolano]

That’s right

[@VinnieVega76]

Where are you touching your positive cable? Inside the wiring harness?

[@BulletSolano]

Yes

[@BEAR-]

Which pin do you put the positive wire on when testing the Solenoid?

[@BulletSolano]

Yes

[@leopoldrobert4498]

Do you change it everyday?, clean it well it wont be leaking anymore :).

[@VikitorSabino31]

Hello bullet my master of accord's, I changed the idle actuator of my honda accord to 5 days and everything worked fine until today I called and the car had those acceleration oscillations again, I checked the car on the Scanner obd hondash and it doesn't work no error, what can i do to regulate this acceleration, is now getting between 1500 to 1800rpm with the car stopped in P or N.

[@BulletSolano]

Vikitor Sabino hey bro if you get a cheap part is going on fail,but first check for intake leak or probably the idle air control valve gasket is leaking!! But if the part is cheap get another one with new gasket

[@lowlifelevi5022]

Okay this helped alot but quick question can I get a link to that air intake

[@BulletSolano]

amzn.to/3v7VLXD

[@arielban1]

Bullet, what camera did you use? the clarity is awesome. thank you

[@BulletSolano]

+arielban1 thanks Bro for all my videos I use a Sony RX100. I live that camera is very good

[@arielban1]

Thank you Bullet. I have the Sony DSC unit.. the predecessor. Mine is 10MP. Your unit is 20MP. After seeing your video, I will upgrade. Hope to get a good deal during November.. thank you again.

[@BulletSolano]

+arielban1 no problem Bro. I was thinking on changing the camera but I think I’m good with it

[@christopherhernandez9115]

The p1259 code still comes up on my 2.3l. F series new solenoid valve assembly wiring is good what else can it be ?

[@BulletSolano]

Computer

[@christopherhernandez9115]

@@BulletSolano can u help me test the wiring from the computer to the connector send me a email I’ll mail u my info yea

[@lewisgivens4564]

In my hood where you removed the hoses I don’t have the same setup and it’s a 98. Where you’re big orange hose is mine is connected to the other ones under it and essentially I don’t have a hose where you’re orange hose is I only have the set under that

[@BulletSolano]

My setup is different because I have a cold air intake

[@lewisgivens4564]

Bullet Solano ahhhhh ok I’m not too familiar with it but thanks man the video helped regardless

[@BulletSolano]

No problem

[@doradean7661]

Hi, Bullet! I'm trying to find the oem part to that gasket you were referring to that would need replacing if we remove the thermostat housing. I plan to change out the thermostat while I'm doing the solenoid gasket. Would that be called the thermostat case gasket, if so, I see two of them listed for my 98 honda accord 4 cyl, 2.3l: 91312-POA-000? or is it 91312-P0A-000? Do either of them need gasket sealant applied? Thanks a million!

[@BulletSolano]

Hi, Is the 91312-P0A-000 and you don’t need sealant for it

[@doradean7661]

@@BulletSolano Oops Bullet, I gave same number to both gasket parts. I meant 193-PTO- 000 being the other. Just wanted to make sure I don't use the wrong gasket as I don't want any leaks. Thanks Again!

[@BulletSolano]

No problem

[@stalkedskinwalkers9811]

Bullet I have a favor. Brother what does it mean when a h22 is shooting water out the exhaust about 4 ft at half pedal

[@BulletSolano]

Condensation, that’s normal in cold weather

[@frios966]

Should I put threadlocker on the bolts

[@BulletSolano]

No need

[@kylecurties1139]

My 98 Honda accord won't start. I have replaced the battery and alternator and still haven't got it to start what could be the problem?

[@BulletSolano]

Check your main relay if that one works and the fuel pump is working your distributor needs to be replace kzbin.info/www/bejne/iKbThIeLpsxgmLM

[@saywhat5696]

Hey what if my 2000 accord ex coupe still has p1259 but only leaks a tiny bit

[@BulletSolano]

The code is when your oil is low or the valve is not working, if you have a leak that’s a different problem

[@saywhat5696]

@@BulletSolano ya once i caught it abit low but that was long Time ago but i think it needs half a quart every 3000-4000km i change m'y oil little later after i put in half a quart since then. its probably dripping a drop everytime use the car

[@bmtv577]

Hi, are those gasket seals fitted on the RA6 odyssey 2003? F23 engine? Are they the same model?

[@BulletSolano]

Should be, but look for a new one at the dealership for your vehicle

[@basillly]

hey, did replacing the solenoid make your shifts feel smoother?

[@BulletSolano]

Is the same

[@patrickkoenig8489]

Hey Bullet, I bought a 2002 Honda Accord 2.3L VTEC about 2 months ago, long story short.. The mechanic said rebuild I am getting codes P0700 HONDA - Automatic Transmission Fault P1750 HONDA - Mechanical Problem in Hydraulic Control System of A/T Clutch Pressure Control Solenoid P0135 HONDA - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1 Any history that you've head with these codes or the hard shifting, That can help me?

[@BulletSolano]

Hey how are you, P0135 you need oxygen sensor P0700 you have problems with the transmission controls P01750 Possible causes Faulty Range Position Switch Range Position Switch harness is open or shorted Range Position Switch circuit poor electrical connection

[@JCollins38]

My gfs accord coupe loses acceleration after about 4-5k rpm and check engine light showed vtec solenoid as the problem, does it need a replacement or just cleaned and new gasket?

[@BulletSolano]

Check the valve maybe you need a new one, put the cables to your battery to see if the valve works, if not replace it

[@JCollins38]

Bullet Solano should I go ahead and order one just in case it is broken?

[@BulletSolano]

Check it first to save some money

[@balazosolano1370]

👌🏽

[@basillly]

if the vtec solenoid is bad can it cause low oil pressure? it's like i have to gas really gas it to get it moving

[@BulletSolano]

You have a different problem on your hands, you know that the problem is low oil pressure? Or maybe transmission problems?

[@basillly]

i've noticed there's an leak coming from somewhere but i'm not sure. i'm kinda pretty sure it's low oil problems

[@Ottonic6]

Hey Bullet. Haven't seen any videos lately, if you have some, I'm not getting notices. Did you get your new car (maybe that;s why no videos)? Love your vids, and am just curious.. Thanks! Take care.

[@BulletSolano]

Hey Dano, how are you man, I posted at least 2 videos per week!! I don’t know why yo you don’t get the notification

[@josem.9700]

Will this help clear out code 1750 on my 02 accord lx. My D4 light blinks after running the engine so long and D4 gear won't work properly even reduce my speed and start pulling back and forth with no signs of acceleration??

[@BulletSolano]

No, this is for the engine, your code is transmission problem, replace the solenoid

[@josem.9700]

So just replace the shift solenoid? I see some run for $40-60 and I see an "original" solenoid for over $230 can a price make a difference in been original??

[@BulletSolano]

Yes, more expensive more better

[@josem.9700]

Muchas Gracias Senor!. I'm taking your word on this. Good informing video!. 👍👍

[@BulletSolano]

No problem

[@bidsanand]

Should i drain the engine oil before taking the VTEC solenoid ..?

[@BulletSolano]

No you don’t have to just put a rag under the solenoid before you removed it

[@ludmula3756]

Did your management light come on and it was misfiring ?

[@BulletSolano]

No, I did this to show how to fixed this issue

[@jxelll6640]

With how many Newtonmeters are the screws tightened ?

[@BulletSolano]

9 lt-lb or 12.20 Nm

[@javierochoa432]

How can I know if my vtech solenoid works in my 98 Honda Accord 2.3 ...it doesn’t rev pass 5 rpms

[@BulletSolano]

Check for resistance on the connector and put power to the solenoid to see if it opens, but if the car doesn’t pass 5K rpm it means that the solenoid is bad or dirty or probably you have low oil, most likely the solenoid is bad

[@javierochoa432]

@@BulletSolano my oil is full n justed finished doing timing belts n water pump

[@cer2us]

Just did mine along with the distributor, now no oil leaks .

[@BulletSolano]

Nice

[@ejaymaria8760]

What's the part number for small gasket that goes on top

[@BulletSolano]

amzn.to/3FFKh1W

[@stalkedskinwalkers9811]

Bullet I'm in the crisis, I need your help.! Woke up today been hearing a little jangling around from a starter plate. Crank it over it felt like it was going to go and then all I can hear is my starter spinning like my bolts fell out what do I do and where does the starter hook into the crank? Ain't their gear there like a pinion for the pitch on the starter?

[@BulletSolano]

kzbin.info/www/bejne/roDRdKRohq2cqsU

[@stalkedskinwalkers9811]

Also bullet do I have to pull the whole transmission if my flywheel fell off from my bolts falling off on a 2.3 VTEC single overhead automatic transmission

[@BulletSolano]

Yes

[@tannertk6851]

Este solenoide es el que causa que mi Accord no pase de las 3000RPM?

[@BulletSolano]

Si ese

[@bree8830]

Gaskets part numbers for both gaskets ?

[@BulletSolano]

Dorman 917-170 Variable Timing Solenoid Gasket www.amazon.com/dp/B00TEFMBFY/ref=cm_sw_r_cp_api_i_UfRREb166KW8W

[@taylormadegang3003]

On my 2002 Honda Accord SE I was able to take the catalytic converter off and put a straight pipe on and do the spark plugs and wires but I still have acceleration issues like almost a dead pedal... I'm lost now on what to do next

[@BulletSolano]

Check your Idle Air Control Valve

[@taylormadegang3003]

Bullet Solano okay gotcha I'll check that now

[@BulletSolano]

Ok

[@taylormadegang3003]

Bullet Solano I took the valve off and it looked fine but it's missing the gasket around it and it seems like the opening and closing of the valve might not be closing completely

[@BulletSolano]

If doesn’t have gasket that’s where you have the vacuum leak

[@Cg6_4oh8]

I Replaced it bro but it still bogs when I’m accelerating ?

[@BulletSolano]

Did you have problems with vtec? If not your problem is something else, probably spark plugs, cables, rotor and distributor cap can fix that, or cleaning the egr passage, sometimes your fuel pump is the problem

[@kylecurties1139]

I got the 2 bolts on top of the solenoid off but the guy I got the car from replaced the solenoid and stripped the bottom one it's round I can't get a open end wrench on it or anything else any advice?

[@BulletSolano]

Man that’s crazy, you’re gonna have to get creative on that one, and if you can’t get a tool in there probably the best option is to removed the thermostat housing

[@kylecurties1139]

I have never done that before is it hard I watched your video on how to but you seid it is a pressurized system and you have to bleed it. How do you do that do you do it while the car is running? Do you have to drain all the fluids from the car? Should I buy a o ring befor in case I have to replace it? Sorry for all the questions but you seem to know your stuff that's why I each your videos

[@BulletSolano]

No problem, remove the antifreeze then remove the housing and yes you need new gasket, and after the installation put the antifreeze back in the car and in the thermostat housing there is a little bleeder valve to bleed the system.

[@BulletSolano]

kzbin.info/www/bejne/n4SmiKF7abqKhNU

[@kylecurties1139]

What is the gasket I need to replace is it the thermostat gasket or the gasket for the thermostat housing?

[@jaylunaguitar]

Hey Bullet, what kind of wire did you use to test it exactly? It looks like one of those aligator clip things. Thanks.

[@BulletSolano]

Yes

[@jaylunaguitar]

The bottom bolt below the oil pressure sensor is awful I can't get it off. I got a stubby 10mm and an 10mm offset wrench and it's making the tool slip. I also took the sensor off to have more room.

[@jaylunaguitar]

@@BulletSolano Update, got it off. It was just stripped really bad I had to take a hammer and chisel to it 😆. I eventually was able to turn it out.

[@hotice1n1]

So i clean the VTEC use brake cleaner and put new gasket . Install it back but it won’t rev past 4k rpm . I put a quart of oil and still doesn’t past 4K . It shows it has oil . I don’t want to over flow it with another quart heard not good to have to much oil in it

[@BulletSolano]

Did you check is the valve works?

[@BulletSolano]

Use the battery like I show in the video to see if the valve works

[@hotice1n1]

Yeah i added some more oil and it work . I had VTEC the whole time just had that nasty leak . I still have to do the egr was gonna clean it but i saw you use throttle body cleaner was scared to clean it with brake cleaner

[@BulletSolano]

Ok that’s good and when you get to the EGR passage don’t put cleaner in the Idle air control valve because you probably are going to damage the valve just clean the plenum with a rag

[@hotice1n1]

That already happen to me before when i clean intake lol it rev hard afterwards had to get a new one at the junk . But thanks your video are always fun to watch .