How To Fix Traction Control Light on HUMMER | How To Fix Service Stabilitrak Light Fix on HUMMER H2

How To Fix Traction Control Light on HUMMER H2 | Service Stabilitrak Light Fix on HUMMER H2 | C0710 code Steering Position Signal Sensor Replacement
#HarjinderSidhu #TractionControlHUMMER #easystepsdoggies #SidhuDIY
🙏 Shop online at Amazon - www.amazon.com/shop/mrsidhu3250
Any Amazon Link in my description is an affiliate link. “As an Amazon Associate, I earn from qualifying purchases.” I would greatly appreciate it if you considered supporting my channel while shopping on Amazon by buying anything you need on Amazon after clicking on one of the links. This gives me a small commission at no additional cost to you and helps me to continue producing more videos! Thanks a million for your support!!🙏
2008 HUMMER H2
It's not necessary to take out the whole steering wheel assembly.
The only reason I have taken out the steering wheel is for video purposes.
2006-10 GENUINE CHEVY GM HUMMER STEERING WHEEL POSITION
SENSOR 25855607 - amzn.to/2XHr50P
icarsoft scanner - amzn.to/2LswvGt
Tool Set - amzn.to/2RUboyd
Torx Set - amzn.to/2XHr6Sr
Drill - amzn.to/2RLbXdB
PLEASE SHARE THIS VIDEO! & "GIVE THIS VIDEO A THUMBS UP"
Thank you so much for watching and commenting.
PLEASE LIKE, SHARE, and SUBSCRIBE.
My other Channels:
1st Easy Steps - / @easysteps_sidhu
2nd Sidhu DIY - / @sidhudiy
3rd Easy Steps Doggies - / @sherutyson
{This video is for educational purposes only; "Sidhu DIY" assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at Your Own Risk. "Sidhu DIY" recommends safe practices when working on vehicles, Computers, Phones, cooking, and or with tools seen or implied in this video. Any Injury, Damage, or Loss that may result from improper use of these tools, equipment, or from the information contained in this video is the Sole Responsibility of the user and not "Sidhu DIY"}.
Please leave your comments below if you have any questions or concerns. I hope this helps someone out there. Cheers!
*Disclaimer: All information is for educational purposes only and is the personal view of the author.

[@SidhuDIY]

How To Fix Traction Control Light on HUMMER | Service Stabilitrak Light Fix on HUMMER H2 | How To Fix C0710 code Steering Position Signal Sensor

[@EasySteps_Sidhu]

Hello everyone, this is my 2nd channel. Please like, share and subscribe. Thanks.

[@nyzjvmartin8456]

Sidhu DIY can you please show how to access fuse box by the steering wheel h2 2008. Thanks

[@mitchellhewett7328]

He provides the best videos I've ever seen

[@SidhuDIY]

Thanks. Glad it helped! 🙏 thanks for the visit. Thanks for the like and thanks for watching.🙏

[@earlweems5799]

Thank you so much for all of your help and educational and wonderful videos for the Hummer H2 repairs, your videos are AWESOME!! 👍 You are my KZbin Mechanic from now on!😁 Great job as usual

[@SidhuDIY]

Thank you! Cheers! Thank you so much for the like and thanks for watching.🙏

[@dognatious6153]

You are very patient. This is a horribly complicated job.

[@SidhuDIY]

Thanks, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@WQQDS]

Thanks keep the H2 videos coming

[@SidhuDIY]

You are most welcome. Thanks, glad to help. Thank you so much for the like and thanks for watching.

[@WQQDS]

@@SidhuDIY question for you I have a 03 h2 can I put a later model dashboard in place of the 03 year

[@SidhuDIY]

It's possible but it's going tough job. Too many things need to be taken care if you are planning 2008 or later but for 2003-2007 will be okay. Hope it helps.

[@SidhuDIY]

I agree round vents look cool but I like 2008 dash better than the previous H2. Thanks for sharing info.

[@hengsophal4398]

Thank you so much for your goodness videos for owner's Hummer. God bless you Daddy!!

[@SidhuDIY]

You are most welcome. Thanks, glad to help. Thank you so much for the like and thanks for watching.

[@shankarwain4289]

Would love to see the traction control in action ! Especially in Moab or any other rugged country side ! Loved your 4x4 , it's even my dream SUV! From India !🇮🇳

[@SidhuDIY]

Glad to hear that! 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@shabibajwa9816]

Sidhu, you really you really done a great and informative video. Thanks

[@SidhuDIY]

Thank You Bajwa Saab. You are most welcome. Thanks, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@palerider8565]

Thanks from Germany, Great Video 👍

[@SidhuDIY]

You are most welcome my friend. Thanks. Thank you so much for the like and thanks for watching.

[@jackychan370]

Love your videos they are extremely helpful. Keep it posting.👍👍👍☝☝☝

[@SidhuDIY]

Thanks, glad to help. Thank you so much for the like and thanks for watching.

[@uncleremus3211]

Wanna be my dad? Thanks for all the Hummer videos, they are extremely helpful.

[@SidhuDIY]

LOL. You are most welcome, glad to help. Thank you so much for the like and thanks for watching. Thanks for taking your time and sharing great feedback, it really makes my day.

[@infinitelyawesome3885]

You need to take care not to let the steering wheel rotate while you have it disconnected because you can break the clock spring that is behind the air bag. if you spin the wheel to far you will break the spring and your airbag light will come on. just so you know.

[@SidhuDIY]

Good point, thanks for sharing the info. Thanks for watching.

[@hotmasked1]

EPIC Video!

[@SidhuDIY]

Thanks, glad to help. Thank you so much for the like and thanks for watching.

[@sturmbringer2011]

Good video. Did this tighten up the play in the steering wheel at all? I have about 3 degrees of free play before the steering engages and have fixed this in the past on other GM vehicles by replacing the green steering bearing, but I see from your video its white and the sensor is the bearing. Very curious if you noticed a tightening.

[@SidhuDIY]

I didn't have any play with the steering wheel. Everything was fine, thanks for watching.🙏

[@infinitelyawesome3885]

and you also have to make sure it is put back on the knuckle in the same position. If you put it on and it is off by 2 turns in any direction and you drive it you can still break the clock spring. it you turn the wheel and fill resistants' at the end of the turn in any direction dont force it or you will feel the clock spring snap .if you feel it you have stop and remove it from the steering knuckle again and reset the wheel to the straight ahead position . Just count the turns from one end to the other end without breaking the spring . then start at either end and count half the turns and reinstall.

[@SidhuDIY]

Thanks for sharing the info. Thank you so much for the like and thanks for watching.🙏🙌

[@Baatarkhuu299]

Thanks from Mongolia! You are an Awesome! I have Hummer H2, 2004. My vehicle give the fault code C0191. Accu is drained in with in 5 days to empty. Where is the yaw sensor placing in my car? Please, let me help! Best regards!

[@samsen3965]

Oh forgot to ask. I see you are using CR+ icarsoft OBDII scanner. So how do you like it? Does it have diagnosis for ABS, Transmission and Airbag too? Do you recommend it or do you like something else better. Thanks,

[@SidhuDIY]

Yes, I like this scanner it can be used for multiple things. Thanks for watching and supporting my channel.

[@brianbudynski2350]

w d 40 works for me lights where allways coming on spewed wd40 in that area from top and on bottom of area no more lights

[@SidhuDIY]

Thanks for sharing the info. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@fernandosanfranciscoca9278]

Hello Sid. Do you have any vids on Hummer H2, my driver seat moving very tiny jerking forward when I accelerate the car, for instance when I'm on a stop sign and when I move forward you can feel the seats move move slightly forward. Have you ever fix this issue before? Please kindly advise. I subscribe on your chanel but I haven't seen you have that issues. Thank you.

[@SidhuDIY]

Your seat cushion has a plastic clip at the bottom and it could be broken or open, you need to make sure that should fit into the metal bracket and I think this is the reason you feel the movement in your seat. Please check and share the results.

[@fernandosanfranciscoca9278]

@@SidhuDIY oh okay thank you.

[@jrponce875]

I HAVE THE 3 amigos but no codes what can it be??? rotors?? hummer h2

[@TheLuckyhayer]

SSA Bhaji, I have traction control and stability system failure message on my 06 H3. When I try to start the engine it vibrates and engine turns off itself and traction control light comes and goes.

[@SidhuDIY]

SSA brother, it could be your Yaw sensor gone bad which needs to be replaced. Thanks for watching, good luck with your DIY project.🙏🙌

[@daniel020dm]

I replaced yaw sensor on my h3 2006 hummer , and it still says failed stabolizer system what do I do ?

[@jasongomez2513]

You should of locked the steering wheel you will damage turnsignal and abs clock spring

[@SidhuDIY]

Thanks for sharing the info. and thanks for watching.

[@jasongomez2513]

@@SidhuDIY not saying anything bad I just replaced the multifunction turnsignal switch cause guy didn't use the lock pin and mest up clock spring good video

[@jasongomez2513]

@@SidhuDIY did you have to relearn the sensor or not

[@jasongomez2513]

@@SidhuDIY when he installed the new angle sensor he said the airbag light came on and traction light and so ran scan and clock spring broke so when I install new one I use the lock pin for steering wheel I rescan it and angle sensor said malfunction angle sensor could it be bad from factory or he didn't put it on right

[@SidhuDIY]

It could be a DOA. I tried my best to explain in detail and how exactly to do it. Most of the times peoples watch the video in bits & pieces and they always miss the important steps.

[@mikepell9847]

Great video but you should lock the steering wheel in place because if you don't and the steering wheel keeps turning making multiple full turns you can bust your clock spring that way then you will have an airbag light on very important lock your steering wheel in place remove the key

[@SidhuDIY]

Thanks for sharing great feedback, I really appreciate it. Thanks for watching it.

[@erwinburger9938]

I have a 2009 H2 and the stabilitrak and traction control error shows on the dashboard. Also when it comes up while driving it no longer changes gear, is that normal? Would I need to replace the same part as in your video or could more be going on? What is the OEM part name and part number which you changed in your video? Thanks in advance for your response.

[@BossPrepping]

does it go in 1st and 2nd but will not shift into 3rd or higher like all you have is to 2nd gear?

[@zekigoktas1811]

Hoi I did it the same way but I don't get that service stabilitrak light not out even after resetting.steel coming back. must I have to program that or calibrier that ore program to zero position .only the stabilitrak light is on. i have change also the brake paddel switch.

[@SidhuDIY]

Did you get the same code on the scanner that I have got?

[@zekigoktas1811]

​@@SidhuDIY . in the first place the scanner gives the traction controle en the stabiltrak problem en the engin runnings not normal after changing de steering sensor only the stabilitrak. ligst go on .nowbady can tel my what the do even the dealer dont no. they say come to us en we help you but i dont want to go to the dealer.the abs sensors are ok en the hight level sensor are ok. must i have to do samting after changing the steering sensor ??? thanks fore answering

[@SidhuDIY]

After reading your comment I believe you have a faulty steering sensor and you might have to get a new one. I hope it helps, good luck with your DIY project.

[@zekigoktas1811]

@@SidhuDIY is that normal when you buy new frome rockauto anew one en its faulty ?

[@SidhuDIY]

Yes, it could be possible. It happens to me on many occasions that I bought things as new and they never worked so I took them back and auto store they test themselves and found out that it was indeed bad. So you never know, nothing is guaranteed in life.

[@rajahomes2431]

Sir ,what is the price for this part ,

[@SidhuDIY]

It's $79 on Amazon. Here is the link amzn.to/2XHr50P For more information please check the description of the video. Thanks for watching, good luck with your DIY project.

[@jiboabdul9731]

I have this sem problem with Homer 3

[@SidhuDIY]

I hope my video will help you out in your DIY project. Thanks for watching, good luck.

[@robertsanchez7169]

Looks like a major pain in the ass.

[@SidhuDIY]

Yup... but it can be done. 🙏 thanks for the visit. Thanks for the like and thanks for watching.🙏