How to Fix / Upgrade Motor Engine Mounts for $22.78 | Polyurethane Mount | 3M Windo-Weld Review

3M Windo-Weld is the best material to use to make cheap polyurethane motor engine mounts. Take about 24 to 48 hours to dry but once you install it back into the car you will notice a night and day difference. This will work to make engine transmission mounts more stiff and provide better handling.
‪@3MAuto‬
3M Windo-Weld on Amazon: amzn.to/3CiMwWB
AirTite Caulking Container on Amazon: amzn.to/2XrfTHI
Top 20 DIY KZbin channels to watch: bit.ly/2JQHlXX
More About BundysGarage:
goo.gl/qv3Wzc
Questions, Comments, Concerns:
[e-mail]
Twitter:
/ bundysgarage
@bundysgarage
On The Web:
www.bundysgarag...
Music by Randall Kent: As seen on NCIS
• Randall Kent - Going H...
All Rights Reserved 2021
© Copyright 2021
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: [e-mail]
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.

[@JL-vx1fn]

I did this 10 years ago on a S2000 rear diff mount for my s2000. It is still going strong! Make sure to check the expiration date on the tube when buying. I had to return mine because it was rock hard inside the tube from the store. 😮

[@Thesaurcery4U2C]

Squirt a little windex on your finger, or on any tool that you choose to use to smooth the surface of the urethane with. It won't stick to windex.

[@bundysgarage]

Thanks for the tip!

[@Thesaurcery4U2C]

@@bundysgarage I used to install windows years ago, and we would work with the urethane every now and then.

[@SaintChicagoJay]

Used this tip today worked flawlessly lol thanks

[@stachowiaks2152]

Hey Bundy! I sold my Honda but still appreciate your videos.

[@suspiciousskepticism6306]

lol... set of bushings for my car is 1k + and I picked it up for 15 hundred... this might be an alternative to doing the one that need it rather than goin down to the subframe to use all of them. Or maybe I should get a honda..🧐 either way, good content... thanks man...

[@suspiciousskepticism6306]

Pro tip... wd40 for getting it clean up... really good on tar as well...

[@Dyl_Cam]

Oh damn thanks I was trying hella stuff

[@BMWExpert]

Perfect for tar i must admit

[@DanielPowless]

Why did you cut off the weight? What does that do?

[@anthonydoane4669]

Doing this will save your other bushings and tie rods

[@BMWExpert]

I wonder, is it safe to use it on suspension parts too? 🧐

[@jennie1294]

I tried it without even taking the motor mount off the car and it's still going strong

[@bundysgarage]

Hell yeah!

[@Queso305]

I used fast orange oumice soap to get it off ny fingers. Should it be applied in layers to allow it to dry quicker though?

[@nicholasvonrhine6311]

Outstanding.

[@gero195]

Held my civic driver bottom mount only with out top mount stripped bolts never fixed it lastwd 3 years till it was sold , dogged it everyday.

[@phoenixelizalde9809]

Nice

[@jennie1294]

🎉😊