How To Flush 350Z G35 Manual Transmission & Differential Z33 V35 EP. 24

[@350zKiller]

Also if you do have a vlsd make sure you read this in case you don’t know how one works! So if you didn’t know a vlsd uses a silicone based fluid that when you’re driving and increase throttle the silicone fluid heats up causing the rear end to lock up and spin both tires also never lift the car and let it idle in the air or off the ground with a vlsd or you’re going to burn it up faster than it will take you to realize what you’ve done to your differential also a vlsd no matter what will slowly wear and become a open diff as the silicone fluid that’s inside the differential is sealed and can’t be changed so once the diff is shot it’s shot, but you can still change the normal gear oil. Just a tip for those who are new to differentials and cars in general as I’ve seen people do this before in a shop and then they had to buy the customer a whole new differential..

[@Wrappedinadrift]

Just got a z, gonna do a lot of maintenance work, thanks for the tutorial man. I'll definitely be watching more videos on tips. Thanks for making videos to help us other vq boys.

[@NmajGaming]

Breaking torque with a torque wrench. Sweet

[@wendymyers1386]

Obviously that metal in the magnet is because you are broken the transmission when you are burning tires doing drifts! Still killing the!car!

[@fullthrottleperformance]

Hahahaha exactly what it's from lol

[@richardowens7537]

You are like 350z guru thank you

[@narciso19G]

according to everyone who ever drifted a Z with the stock diff says that the viscous diff is no good. when it gets hot it just becomes an open diff. you just need a welded diff to drift.

[@fullthrottleperformance]

I couldn't agree more!

[@narciso19G]

@@fullthrottleperformance thanks for all the vids tho they help out a lot. I didn't realize how old the video was until recently.

[@alk3myst]

Gear oil is one of my most hated smells as well.

[@tone-yo7192]

Wait. New DIYer here and one of the first things I learned is don’t use your torque wrench to break bolts loose and such because you’ll mess with the wrench’s calibration. How do you know yours is still working properly?

[@johnb3587]

You never *ever* use a torque wrench to break bolts loose, you will fuck it up

[@fxeaglepips7109]

Nice Vid...since you had so much sludge in the dif...would it be a good idea to fill it up with new fluid and then drain again to try and rinse out more of the metal and sludge...is it necessary or even a good idea...other than wasting new fluid.....a flush in a sense...I have a 06 G35 Coupe...wanna do these Fluid changes. Thank You

[@fullthrottleperformance]

FX EaglePips These fluids are kind of expensive for the red line and I'm going to be replacing and welding my diff anyways so it doesn't really matter for me. Simple drain and fill should be perfectly fine though, it's what the dealer does

[@350zKiller]

If it hurts you to see him use a torque bar as a breaker bar as well your not alone 😂

[@rattler1633]

yeah i wouldn't do this since it could make your torque spec on the torque bar inaccurate

[@apxl8r1]

You said your differential is acting up. Geez do you think it has something to do with doing all those donuts with the car?🤔🤔

[@fullthrottleperformance]

😂😂😂I know that's the reason, but doing that is also the reason I bought this car lol

[@apxl8r1]

Full Throttle Right. Well its good that you caught the problem. Keep up the good work. 🙂

[@fullthrottleperformance]

Thanks for the support man, it's much appreciated!

[@willk3807]

Nope lol

[@alsn126]

Hi; good vid. Very informative. Just one question do you do differential AND trans fluids at the same time when your changing out your transmission fluid?

[@thanhau8]

You might as well since you’re under the car

[@ky0611]

Should the transmission be warm when changing?

[@fullthrottleperformance]

Doesn't have to be, but can, and most of the time is when we do these flushes

[@aleon117]

You put the same oil in diff and trans?

[@fullthrottleperformance]

No, trans is GL-4 diff is GL-5

[@alk3myst]

Can't go wrong with SPL Parts

[@NSWNY]

Always take out the fill plug before you drain it.

[@fullthrottleperformance]

Hahaha, I think I actually said to remove it first then forgot myself lol

[@davidk033]

Idk if you still have your 350z but if you do how does the shifter feel ? I’m planning on getting the same oil you did for my Z

[@moechura5767]

the king really ✌✌😚😚

[@ubertinoayala8837]

Do you replace the crush washer on both plugs?

[@fullthrottleperformance]

You're supposed to, and we do here just because I'm a specialized Nissan Infiniti shop. But if it were my personal vehicle, I'd replace the drain plug one, but the fill is probably fine to leave

[@bravo3601]

Thinking of getting a 350z like your videos Bro Keep it up

[@fullthrottleperformance]

Enrique Bravo it's an awesome car 👍

[@saifulnidzam5171]

How many bottles do I need to buy.. 2 or 3?

[@thejohnbeck]

1.5 qt

[@jellyleggs1635]

I thought you gave up on KZbin. Keep them coming :)

[@fullthrottleperformance]

Carlos Hernandez Lol, just been busy. Thanks for the support tho! Much appreciated👍

[@StrappingYoungComrad]

Video on replacing the drive shaft carrier bearing would be sweet 🖒🖒

[@fullthrottleperformance]

Honestly that wouldn't be a bad idea. I'll see if I get this g37/g35 soon, Ill do a short vid on how to install it.

[@caitlyngomez9836]

I own a automatic 350z how often should you change your transmission fluid?

[@fullthrottleperformance]

Do you know if it's ever been done before? And, how many miles are on it?

[@angmccarty4621]

I know this is not relating to this video but we’re is the tcm box in the 350 z

[@andreslatorre1466]

Hi , are you using same fluid to transmission and differential? And how many quarter total for this? 🙂

[@andricksgarage8745]

GL4 is the Trans, GL5 is the Diff

[@bradleyhurd6717]

You shouldn't use your torque wrench as a breaker bar.

[@fullthrottleperformance]

After that wrench stopped being reliable, I stopped lol. Now I have a nice digital torque wrench

[@ricergarage3092]

Just got a Z a week ago, my reverse gear is grinding so I wanna replace the mtf with synchromesh to hopefully get rid of that problem. Thanks for having post this video. Edit: also what kind of socket are you using for the drain/fill bolt??

[@fullthrottleperformance]

It's a 10mm allen head / hex bolt. And I've had my best experience with Redline MT-90. Just make sure if you're filling the trans, it's GL-4 only. The differential uses GL-5

[@epzads]

Hey I bought a used 2003 Nissan 350z touring and changed automatic transmission fluid should I change differential fluid also the car has 160k around miles I don’t know the history of differential fluid change? Is it going to create problem if I replaced the old fluid with the new one ( penzoil 80w 90 bought from dealer ) please let me know thanks

[@fullthrottleperformance]

Sorry for the super late response. Yes thats the dealer supplied fluid for the diff

[@willk3807]

I was under my Z and noticed 2 of my transmission bell housing to engine bolts are missing. The two at the very bottom are gone but luckily it's not leaking fluid. This sucks cause I don't know the bolt specs

[@tristanoliver2911]

Bell housing bolts just hold the trans to the engine. It’s okay to be missing them.

[@RellekZone64]

thanks, 05 G35 sedan 6mt, should be basically the same process correct?

[@fullthrottleperformance]

Benjamin Keller same exact process

[@RellekZone64]

Perfect, watching your videos has saved me time and money!!!

[@fullthrottleperformance]

Benjamin Keller Awesome! I'm glad to hear it 👍

[@infinitig3549]

You use the same type of oil for the transmission and differential?

[@fullthrottleperformance]

Sorry for the super delayed response. No GL-5 goes in the diff but not the trans, you'll kill the trans with GL-5 in it

[@theripper121]

I'm kinda surprised that Nissan put in a VLSD in the 350z/G35 and 370z/G37 and not a torsen type.

[@fullthrottleperformance]

theripper121 Yeah the vlsd sucks. They put in a shit diff for these cars. Ugh, gonna be welded soon lol

[@austinwagner5597]

Where’d you buy the adjustable lower control arms in the start of the video?

[@fullthrottleperformance]

SPLPARTS.COM

[@hernanmurillo8925]

Is that a torque wrench your using to remove the bolts ?

[@fullthrottleperformance]

Hahahaha, yeah I must've grabbed it and used it for both removal, and replacement lol.

[@hernanmurillo8925]

Full Throttle that’s super bad for the torque wrench my man, it can throw the calibration off and not give proper readings anymore. Good video though

[@fullthrottleperformance]

Yeah, I know. I don't usually use it like that, it's only a $20 wrench tho. Thanks for the insight tho, much appreciated

[@dirtyr1937]

What size do I need to remove the bolt

[@muddyrelic3009]

So redline Mt-85 is good🤔 or will it rape my trans Z

[@fullthrottleperformance]

It's what I like to use, but make sure it's GL-4 if you're putting it in your trans Sorry for the super delayed response

[@abdifranco6002]

What’s your eBay store called?

[@1elwin]

I’m doing this with jacks prefer lift the back with 2 stands or add 4 stands?

[@muncheymuncher3368]

4 stands minimum anytime you under the car bro are you still alive??

[@Aznchrispie]

how long does manual transmission and rear diff fluid last?

[@fullthrottleperformance]

I change it every 10-15k miles. I think the dealer recommends every 30k.

[@ashbyash7915]

Will a regular wrench do it ??

[@Leolpzz]

Same for an automatic ???

[@fullthrottleperformance]

No, you can do a drain and fill, but I don't recommend changing the fluid after 60k miles.

[@ElSesh]

I have a 2003 350z it currently has 87,445 original miles. I’m not aware of it’s maintenance history. Would you recommend me changing the transmission fluid on it? What fluid did you use on your trans and diff?

[@fullthrottleperformance]

I use redline GL-4 mt85 or mt90 I believe is the one I used, but always do your own research. And yes, I think the fluids should be changed. I forget what mileage it specifies in the FSM but I think its every 30-60k miles.

[@ElSesh]

Full Throttle you don’t think the fluid would be too dirty if it’s never been changed throughout the 80k lifetime and would cause damage to the trans? I just wouldn’t want to change it and have my trans slipping between shifts.

[@fullthrottleperformance]

Is it auto?

[@ElSesh]

No it’s a manual.

[@fullthrottleperformance]

You'll be fine, I didn't change mine till I bought my car, and it had 92k miles when I bought it. Now at 140-150k, and I've changed it like 4 times since

[@andreslatorre1466]

Hi , how many bottles did u use it ? and do you know if all 350z are open differential or slip ?

[@g35tho11]

Best thing is to call Nissan/Infiniti dealership and give them your vin

[@Ghostw48]

The base model is the only one without the VSLD all the other models have it unless its been swapped

[@ivansantiesteban4094]

Hey man I been a fan for a very long time..I just recently purchased a drive shaft from you. I’m looking forward to future purchases. Thanks in advance and keep making videos for us. Send me stickers if possible to rep you’re shop. 🤙

[@fullthrottleperformance]

Ahh you just bought the G35 M/T drive shaft? Thanks for the support man! Much appreciated! I would've thrown in something if I knew it was a YT fan. Send me a message on eBay if you ever buy anything else. I need to make stickers for real tho lol

[@ivansantiesteban4094]

Yes sir that was me. Next time I’ll shoot you a message ahead of time..I really love your channel keep it up..we learn so much from watching your videos. I felt so much more comfort when I found out you’re the seller.lol good job on the item photos by the way.

[@fullthrottleperformance]

Thank you! And I try to max out the amount of photo's ebay allows lol. I did split the drive shaft though, but both sides were marked to allow you to put it back the same from the factory. Let me know if you need anything else. Next time I'll give a % off.

[@benefitsvang9513]

What brand of fluid do you use?

[@gamingm8604]

is this process the same on 370z and G37???

[@fullthrottleperformance]

Should be almost identical, the only thing that might be different is the fluid capacity, and fluid type.

[@imthecakesters6863]

So you used gl4 75-90 in both your manual transmission and diff?

[@wpafreddy]

Gl4- trans , Gl5- diff

[@imthecakesters6863]

THICC daddy F Thanks!

[@Hawlkeye-e9p]

Perfect example of why you stick to manufacturer specs. Dont use any after market fluids ever.

[@daveyofyeshua]

Liking the channel dude, David here from the UK. Have you done a video on braided brake lines? I've sub'd!!

[@fullthrottleperformance]

I haven't yet but I am playing a g37 soon for the Akebono Brakes, and if I get it I will be doing a video on that BBK with SS braided lines. And thanks for the support bro!

[@space6712]

How much fluid goes in the transmission?

[@fullthrottleperformance]

3.25 Quarts

[@space6712]

Full Throttle thanks for the quick response, keep up with the detailed videos 👍

[@muertelara866]

How to change speed sensor

[@fullthrottleperformance]

It's pretty easy, it's two sensors attached to one plug, on the rear of the differential, to both sides where the axles meet the diff. I might be able to make a short install video soon.

[@danonino1072]

How do much do I tighten it by hand lol

[@Tuesflex]

What size bolt

[@AidanTheLoverBoyOhDwyer]

What did you drain in between 04:59 and 05:21?

[@williamhinson5523]

That’s engine oil he drained

[@Realtor.joeylean]

Hey Charlie, I would like to ask if I'm changing my trans n diff oil. Do I need to jack all four points up or just jack up the rear will do?

[@Realtor.joeylean]

Full Throttle thank you so much for the fast reply. Thanks for posting such informative videos. Keep up the work. ✌✌

[@fullthrottleperformance]

Joey L No problem my dude, and thanks for the support bro, much appreciated! 👍👍👌👌👌

[@NetoperekMordulec]

A festival clumsiness!!!!!

[@jc-ux1hv]

hey man! what kind of bolt and what size are the drain bolt and fil bolt?

[@thejohnbeck]

10mm hex

[@ashbyash7915]

How much oil goes in the differential ?

[@fullthrottleperformance]

Luis Garcia Approximately 1.5 Quarts

[@ashbyash7915]

Awesome video brother just what i needed for my z 🙏

[@ashbyash7915]

Hey theres still a few drops coming out where the bottom bolt goes should a tighten the bolt little more

[@fullthrottleperformance]

Luis Garcia Yeah I guess, just don't over tighten it.

[@lumo599]

Bro i have a 05 g35 manual is there nismo parts that i can upgrade to?like carbon drive shaft nismo diff cover from z can it fit the gcoupe

[@fullthrottleperformance]

You can get a custom made drive shaft, but the cf ones from the z chassis, won't fit. The diff cover will, but if you're gonna upgrade your diff cover, I'd go with a z1 cover. Higher capacity and stronger

[@karatejujutsukid8066]

Hey Charlie. There’s grinding when I bang my gears from 1st to 2nd. Sometimes 2nd to 3rd... when redlining it. What can fix this issue?

[@fullthrottleperformance]

You have an 03-04?

[@karatejujutsukid8066]

Full Throttle I have a 2005 base

[@fullthrottleperformance]

What's your Production Date on the driver door sill? You should have the trans revision if you're 05. But what fluids have you tried?

[@znister33]

Hello what’s your ebay name store?

[@fullthrottleperformance]

Eye in the Sky Both of my eBay stores are in the description👍ftpautoparts916 & bestdealautoparts916 thanks for the support bro!

[@klepetar]

thats my car.. same color.. model.. !

[@fullthrottleperformance]

klepetar It's a great color!

[@familieaa1968]

شكرا جزيلا

[@vqt7611]

Old Oil good 🤔

[@ashbyash7915]

What if i dont have that wrench for the 25 pounds ??

[@fullthrottleperformance]

They're cheap at AutoZone, like 25 bucks, but if you don't have one its fine, just don't over-tighten it. I didn't use one for the first two times I did this. Make sure you check for leaks every day after you do this, at least for 3-4 days. To make sure you don't run anything dry.

[@angel559alvarado]

I’m at 103k miles on a mt. Is it worth changing? I don’t know the service history on it.

[@fullthrottleperformance]

Changing the fluid never hurts, I change mine at least once a year

[@josec413]

Hey man i have a question, my car has done this twice since i bought the car, i was driving my z last sunday and i really didnt do a long drive or anything like that, im hardly using the car, and when i hit 2500 rpm with any gear my car would start shaking and my rpm gauge would jump up and down until i lower the rpm but it wouldnt really go pass 2500 rpm any suggestions about wjat the problem might be? Also the fist time it did it to me was like 5 months ago and it hadnt done it since then i think

[@fullthrottleperformance]

Honestly that sounds like your car went into limp mode, have you done any modifications to the car? This can be caused by many different issues, I wouldn't know unless I physically looked at your car, even then I don't know if I would be able to find an issue that has only happened twice. Did it throw any codes?

[@josec413]

Full Throttle i didnt check for codes but the only mod i've done was changing the clutch because the old one was going bad already

[@fullthrottleperformance]

Jose C scan it for current and pending codes. It could be a lot of things, and I can't narrow it down without knowing anything. Let me know if it shows anything, and don't disconnect the battery until you scan it.

[@josec413]

Full Throttle alright man i appreciate it, love watching your channel pretty entertaining keep up the good work 👌

[@fullthrottleperformance]

Thanks bro, I appreciate the support.

[@taylorasbell7074]

Dude stop breaking bolts loose with a torque wrench, get a breaker bar they are much cheaper than a new torque wrench

[@fullthrottleperformance]

I know, lol. I just bought another torque wrench too :)

[@NKillmore]

Am i the only one who doesnt give af about torque to spec, Tighten it Smart and GO.

[@useruseruser444]

U talk too much bruv i just wunna see how gearbox fluid is changed on a 350 hurry up and get to the point ffs

[@fadedndrunk]

I'm no car expert, but I don't think youre supposed to loosen anything with a torque wrench. But who knows, I may be wrong, seems like you own/run a car shop.