How to Install a Swing Storage Box from Vevor in a Dodge Ram

How to install a swing box from Vevor in a truck. For this I’m using my 2006 Dodge Ram. This swing box is a great way to keep any added accessories or tools organized in one spot, dry, and out of the cab. My truck is a regular cab so it doesn’t have loads of room to begin with. #vevor #dodgeram #storagesolutions
5% Discount Code: SAVEMORE5
Get a Vevor Truck Bed Storage Box like mine HERE!
CA: s.vevor.com/bf...
US: s.vevor.com/bf...
UK: s.vevor.com/bf...
EU: s.vevor.com/bf...
Website: 4diyers.com
Patreon: / 4diyers
Facebook: / 4diyers
Twitter: / 4diyers
Instagram: / 4diyers
Tumblr: / 4diyers
Pintrest: / 4diyers
Tools/Supplies Needed:
-10mm wrench
-10mm socket and ratchet
-impact driver
-tape
Procedure:
First is laying out all the parts, you’ll have the box, two brackets that bolt together and fasteners.
Start by putting the main bracket together. It fits over two threaded studs, then using the supplied nuts, tighten it down using a ratchet with a 10mm socket.
For placement of the bracket, first slip it into place on the swing box. Make sure the plastic pivots are in place, then latch the bracket in place towards the front of the box.
I placed a 2x6 under the box to help with some clearance underneath. Considering I have a tonneau cover, the box must be able to clear the hold-down lever. Tape is used to mark out a reference point.
With the bracket removed from the box, use clamps to hold the bracket into place. The latch side of the bracket must also be mounted on the raised portion at the side of the box.
Using an impact driver with a 10mm socket, install a couple of the bolts. These are self-drilling bolts so no drill bits are required. Thread the bolt in like you normally would, it’ll cut the hole and then eventually thread into the steel.
A quick test is done to ensure it’s in the correct position with no interference.
Once satisfied, finish installing the rest of the bolts. There will be 4 by the tailgate and 2 at the latch side.
After that, I used a ratchet and socket to verify the bolts were tight.
A vacuum is used to clean up any shavings.
The latch comes loose from factory and has slotted holes for the alignment. I tightened the nuts so the latch had some movement.
The box is installed and then the latch is adjusted and tightened with a 10mm wrench.
The supplied rubber bumper can be installed, I tried two however I found one was best.
I can finally remove my stuff from the cab and it now has a safe space in the box. There is plenty of storage in this box along with a removable tray.
Here you can see how it fits in my box, this doesn’t affect the main space in the box so I’m still able to put drywall and plywood in the box.
When the box is latched in, simply pull the yellow handle and the box will swing out for easy access.
Even with the tonneau cover on, the box can be easily opened once it’s swung out. The lid can be locked and the box can also be locked in place to prevent theft.
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

[@garybrady7245]

I have the same exact box just for a Tundra model. I think most of the boxes will work with pretty much any truck. I looked online and every box i seen is within 2-3 inches of each other so they seem pretty universal to me. But thanks for this video because i was wondering if i could still get a full sheet of plywood in the bed. I also have a single cab 8ft bed. Like you said not much room anywhere to throw some of your everyday arsenal. Thought about trying to get a Decked System but insanely too much loot for me. But they are nice

[@4DIYers]

Thank you! The only other option would be a box behind the cab, but then you lose bed space in a different way, not to mention your can have a tonneau cover either. While I do love the regular cab short box, I think an extended cab will be the best option for me.

[@trxll.treyyy5797]

are they flush with the wheel wells

[@rogerjosephholder1320]

Great Video, simple and very clear. I just ordered a set of these from VeVo. I am worried about buting directly from them instead of another company

[@4DIYers]

Thank you so much for the kind words and feedback. They are just like any other large retailer, I haven’t heard of any issues with them.

[@jimvalliere1562]

thanks I was thing of getting one of those

[@4DIYers]

You're welcome! I'm extremely happy with it, keeps my truck more organized.

[@M_CNST]

Does it bury the bed hooks or can they still be used? Thanks.

[@4DIYers]

Amazon Tool Recommendations: amzn.to/3QrjM8c Current retailers partnered with me & coupon codes: eManualOnline website: shrsl.com/3vcz4 Coupon Code: 4DIYERS20 (20% off any order) ECS Tuning Website: bit.ly/46tMpXP Auxbeam website: auxbeam.com/?ref=4DIYERS Coupon code: 4DIYERMR10 (10% off any order) Teslong website: teslong.com Coupon code: 4DIYERS (10% off any order) Lanmodo website: shrsl.com/3vczf Coupon code: LMD4DIYERS (Save $50 off order) Auxito website: www.auxito.com/?ref=xR3VZnDW Coupon code: 4DIYERS (15% off any order) Headlight Revolution website: www.headlightrevolution.com Coupon code: 4DIYERS (Free shipping on all US orders)

[@randytellez2451]

Two questions: first off: when I looked at these boxes on Amazon I found a lot of them look exactly alike but different sellers have different brand names on them. Second question: do I need to worry about hitting any wiring at the bracket mount area with the self tap screw?

[@4DIYers]

Unfortunately I don’t have an answer for your first question. I haven’t worked with any other boxes on the market. As for the second question, it’s always a good idea to peak in behind the light, either taking the tail light out or looking from under the truck. For my Ram, there wasn’t any conflicts with wiring.

[@klvs2ply]

VEVO says 2019 and up on your link is that what you used on your 2006?

[@4DIYers]

Yes I did. Took the gamble and it fits perfect. I can't see them making a bunch of different models for each year of truck.

[@garybrady7245]

@klvs2ply I'm pretty sure most of them are universal. If you look up some of them and go to the specs they're all within 2-4 inches of another. So in other words I think a Dodge box will fit my Tundra bed as a matter of fact I know they will. All you have to do is measure your height (I took off a inch) didn't want anything dragging and you can raise it a little bit when you install it. If driving a few screws into your truck bed bothers you then these aren't for you. But yeah I think they'll fit alot of trucks no matter the vehicle make

[@Reezexx]

I thought there was a way to install this without using a drill to dig in to the box

[@4DIYers]

As far as I know, no.