How to Install a Waterproof Rear eBikeling Conversion Kit

[@billelliott2374]

Kit i just received has 2 torque arm kits and the cadence sensor is a new split type(really easy to install) no crank removal required. I did the same installation of brake switch/tab because integrated Shimano gear controls. I am impressed with quality

[@motrhead69]

Just installed the 1500 w version to my GIANT cypress 700c installation was straight forward and waiting for my battery pack took a month after my initial kit from Chicago arrived,I'm pleased "so far" able to reach 31 mph and my battery pack still has life left before needing recharge.

[@scottmcintosh8136]

I built a class 4 ebike about 8 months ago. That means I have no PAS system. I do 30mph with ease. I can go well over 30 under the right conditions. Keep in mind, just because I can go that fast doesn’t mean I always do. I have and do push the limits of my bike often, that does mean I take mountain gravel roads and trails that dirt bikes are on. I also have had multiple problems come up and had to learn a ton about every component involved. Ive had to find answers to problems even the experts that sell and work on the expensive ebikes don’t know the answer to. I’ve had to learn the hard way, many times those same people have been completely wrong. It seems they always advise the most expensive way to find and fix the problem first, even if they aren’t going to be making any money out of it. At this point the only original parts from when i began this journey are my battery and my motor. I began watching this video to see if there was one component missed, and there is. Not long into the video you see him put the disk break directly onto the motor hub. I did the same as it seems no one has taken into consideration one result of this. When you’re going down a steep hill or slowing down from higher speeds that disk break is going to get hot. Extremely hot. In turn that disk break is going to make your motor hub hot too. And as you work the motor going up it stays hot and back and fourth. This heat, I now believe can travel from that disk break, make the motor hotter than it would be, and follow the power lines, all of them, back to the controller, and even into the throttle. There is a plastic connector for the 5/6 wire connection of the hall connection and such. I’ve melted that twice. I had melted it the first time and had a ebike shop fix it for me. They told me I had been taxing the battery too much going up hill. Unknown to me they replaced it with the same part than wrapped it in a bike inner tube and made it look like it had been heat shrunken. I was pretty mad when it melted again. There’s more to that but I digress. I fixed that by hard wiring that connection and insulating it. No plastic to melt. I rode very hard on some mountain passes yesterday. My throttle went out for the second time, but I wasn’t aware of it until this morning. I took both thumb throttles apart. The wires were broken in the same spot in both. Either the wires are arcing. Or my theory about heat building up through the wires as a result of the disk break getting hot. Or. As a 3rd very real possibility, the parts are just made cheep. I did some research and found that the throttle I payed $37 for 2 times. Is sold on the web for $7. Just sold under a different name. I have what that store called a beefier throttle now, and my bike is running, they gave me this throttle for free. I’m not hopeful it will last and plan to replace it. My plan is to go to a scooter or motorcycle shop and find a heat gasket to put in between the motor and the disk break. No idea if it will help. But I hope so. Let me know what you think or if you have any ideas. Thanks in advance. 26” 1000w 48a rear hub motor

[@andresfeliperamosromero3060]

Great e-bike, Great customer service

[@williamcarroll5402]

Is lovely. My little brother has the front wheel on his mountain bike it surprised us how good it is for its size.

[@ebikeling]

Thanks for the comments. Ebikeling's quality product will exceed many customers expectation. The power, durability and quality is excellent. You can see more quality product from ebikeling on www.ebikeling.com

[@hakulus3037]

FWIW my 3 ebikeling kits (early 2021) all came with a pre-lined rims, meaning they all had rim tape already installed. Thanks for this video, its the best of the batch I've watched.

[@herbertwerner2287]

I think Ebikeling is a great company with great products and a kick-ass video intro. Top notch !

[@conchubharbeats]

Iv seen ppl take hours on tyre was a pleasure watching a simple tyre tube swap

[@samsonhinds7953]

I have hydraulic disc brakes do I need to mess with the brake system? I don’t want to solder or switch the brakes so j am very very confused

[@jesuscabrera3976]

Hi ebikelink, its being almost a year since this video, how is the bike going? is the motor working good? are the waterproof component reliable? have you had any issues at all with it? thanks

[@ebikeling]

Our conversion kits are getting increasing number of attention and everyday new customers are discovering the joy of riding electric bike using ebikeling conversion kits. Number of complaints are significantly low compared to number of satisfied customers. Our team work dedicatedly to provide the best product to our customers. Our high performance motors last years and we try to offer best waterproof components to make the whole set work perfect and last years..

[@Conservator.]

@@ebikeling Hi, How would the torque arm prevent rotation? At 4:19 when accelerating the axis and the torque arm would turn clockwise. The point where the two pieces are bolted together would pivot and the piece attached to the axis could turn up (down if the bike is with the wheels on the ground) with relative ease. Don’t you need a torque arm that’s specifically designed for a rear hub motor? Thanks in advance!

[@splicecentral9079]

Lol ebikeling is the company that sells these not a customer that built an ebike 😆

[@gabrielomblero281]

@@splicecentral9079 😐😐

[@tomcarney1193]

@@ebikeling do you make a rear hub for 29" wheel with a built in controller?

[@robertbrawley5048]

Not mentioned is if the motor has been sprayed with insulating lacquer inside. Probably not

[@ahah1785]

The rim liner tape is more important that the tube itself!

[@antonlavrentiev5249]

Yes! I've done it! It works. I've watched this video probably 30 times. 1 thing I can advise is how to avoid cutting and soldering brake wire. If you have a bend saw or a hand saw and a good wise, you can gently cut off part of the handle base and release the wire. Thank you very much for your video.

[@Juanito_Peligroso]

This industry will get huge if politicians keep their sticky fingers out of it.

[@robertcaffrey6097]

John Woods I agree and people will get fit and lose the fat.

[@erickgregoryful]

I like that it's underground. Of course it wont be like that forever. Nice to be part of the beginning.

[@ghoulbuster1]

The government will surely ruin the beauty of E-bikes

[@erickgregoryful]

@@ghoulbuster1 Yeah. The government tends to do that with anything that makes sense or is good. Sad but true.

[@loganf9701]

@@erickgregoryful In my opinion theirs no practical way for the gov. to regulate this stuff....these magical little machines are far too versatile with unlimited ways to attach/detach , flex shaft drive discretely .... un-less they ban bikes and small motors all together, (un practical

[@therealscoobydoo]

I have the 1200W with the built-in controller, the wheel won't turn when I tighten the axle nut on the gear side.

[@tallman145]

That hub is huge . I want to do this to my mountain bike. but I can find a smaller rear wheel hub that is 750 watts ?

[@tln8424]

My rear hub motor did not come with a cable that runs through the center of the axle I am having trouble mounting the wheel into the dropouts don’t know which side of the left drop out the table should be

[@Thequestionmark_darts]

Great thinking for break cable.

[@IIMANIXII]

Guess whos looking to buy a kit right now - just one more payment on the bike I just bought and then I'm buying the kit - you guys do 29ers with a battery built-in controller option like the grin tech ones...?

[@xxdarwinxx1393]

Hello so I ordered one of these kits and the controller wiring is a SY60 and I can’t find a battery to fit it in I’ve bought 2 batteries that are very expensive and none of them fit what battery am I supposed to use?

[@Scorpionbite8]

My battery comes with a charger. When i saw you soldering and using JB weld, I thought you were tweeking to hard.

[@InspiredByEverything]

What if you have a 21 speed bike? Do you just use your bike’s existing sprockets?

[@jarrodhodge1510]

I just bought a front wheel kit. Where can I buy a charger?

[@deathincarnatesplace]

it is best to diy your alternator because alternators are heavy because they have to stay running in cars and truck in the worst condition like when you hit a curb and the alternator doesn't break.

[@mangodwins6328]

Voilamart 1500 watt is easy to put together 35 mph

[@turbofan450]

Anyone know where I could get some of those mounting brackets seen at 1:48? I mean the two small ones below the battery cradle

[@svlagonda7417]

Great video seeing what's involved. Alot of work!

[@Gtfokthx]

should have put a liner inside the rim, i made the same mistake an had a blow out 6km from home. an the factory rim on those hubs is crap an spokes need to be tightned after 50kms then every 100km

[@gavwilliams722]

I have the same issue with the brake leavers. My only concern is by taking out the cut out switch and gluing it to the brake wouldn't that mean it's no longer water proof?

[@creyes4182]

Yeaaaaaaah, I’m just gonna get it pre-built. I hoped out as soon as he started soldering lol

[@blackbirdxx928]

looks like same calipers as on my schwinn...brake pads lasted 3 weeks...the area where the rear wheels bolts lookes like schwinn to. 1500 watts and 52 volts and no torque arm..guess me lucky

[@yousafbintashfeen125]

The paidel working if battery dead ???

[@ebikeling]

Yes. You can always use your e-bike as a regular bike.

[@TheHouseOfKoinonia]

What’s the number of the disc brake on you motors please

[@mrkeopele]

nice work!! so you got a complete ebike for just over $1000? sweet

[@zara330]

Hello, Great Video! 1. What kind of range do you get on mostly level streets ? 2. What kind of incline can it go up? 3. What is the fastest speed? 4. Does this bike need a motorcycle driver's license now to operate legally? Thanks!!

[@sanesaint8725]

You just need to break leavers and the throttle my twist throttle says the battery level but not the miles per hour but I don't care less wires

[@CoCody_]

The rotor in the ebike kit I bought that goes with the crank sensor doesn't fit onto my bike, how do I resolve this problem? I bought the ebike kit months ago, now I'm building it, but if I can't solve this problem I'm just going to contact Amazon to return it.

[@bigcatsliontiger]

It seems your rear wheel spins alot , mine spins only for 10 seconds after i stops pedals , is this normal for ebike cos its wheel is heavy or not?

[@dougfox9649]

What size tires willthis wheel take, id like to put 42 or larger on the rim.

[@VioUk]

Super! Great job. I want to make my bike electric to for delivery!!

[@mrkeopele]

did you do it? i've quit cars almost %100.

[@kenm2659]

Silly question since I'm new to EBikes. Since it is a rear hub motor, you don't really need the chain and crank pedal right? Only if you just want fully motorize bike.

[@ebikeling]

Hi Ken, This is a pretty good question, and we believe that many people want to learn the answer. Electric bike conversion kits do not eliminate the regular bike features, they just add motor power to the wheel. The hub motors spin with our without chain. You will still need chains to be able to pedal your bike without motor assistance. But, with power assistance you do not need chains or pedaling at all. Thanks,

[@jackdaniels1385]

Witam. Jakiej mocy jest ten zestaw do konwersji roweru? Super film łapka leci Pozdrawiam 👍

[@deathincarnatesplace]

install a 775 motor turning a 40 60 or 80 amps alternator first and then it goes three hundred miles on a charge minimum.

[@dougmartin8495]

How???

[@deathincarnatesplace]

@@dougmartin8495 watch free energy video and then learn make transformers that reduce amperage and then wind it yourself.

[@JorgeClavero]

What os the autonomy with one load?

[@staysafe1096]

Is it rated for rough road like trail?

[@lowlifeNPC]

Bro.. Did you line the rim? Guna get a flat in no time

[@KillerRaptorr]

Largely recommend you remove the controller from the underside of the front triangle where the front wheel is. Your front bike's front wheel will suspension up onto that and cause it to shred that bag up, or bottom out your tire and cause alot of probs. Put the bag on the underside of the top triangle above the battery, This'll make it less likely to get smacked and give your front wheel full ability to bounce. Other then that, nice video. Tho the audio is slightly off at places or to short because of how swiftly you edited the video and cut scenes in.

[@ebikeling1249]

Thanks a lot. Your ideas, suggestions are always welcome.

[@lifestylenourish8836]

Did you install torque arm on the other side ,?

[@aalebhai5079]

I want to make my bike like this how much cost for this

[@Digiphex]

What modifications are necessary to get full power, no pedaling, for off road use?

[@erickgregoryful]

Don't hook up the pedal sensor. Just leave it off.

[@forevercomputing]

An extra powered hub for 2x wheel drive, an extra battery in parallel. Using at full power means they drain quicker. More batteries add weight.

[@MuayThaiMaster319]

Does the PAS sensor have to line up parallel to the rotor or can it be a bit above (but still close to it)?

[@ebikeling]

Hi, They should be lined up parallel to each other. Thanks,

[@AhmedAdly11]

Good stuff!!! Thanks for the video

[@mangodwins6328]

The wire from the tire motor goes between the tire in the axle he didn't show that

[@deridionentertainment]

Please I've been trying to contact you guys about buying a fat tire 20 inches motor wheel but you guys aren't getting back to me. I've already bought controllers and other stuff from your website on Amazon and it's coming in about a week or so. I just need 2 wheels for dual drive diy I'm doing

[@ebikeling]

Hi, Please contact us through [e-mail] with your questions. We'll reply promptly. Sincerely

[@williamfeijen8601]

why didn't you install the pas sensor behind the bottom bracket bearing ?

[@DrewVerdin]

Do they make these for fat tire bikes?

[@kareemvitar6645]

I prefer front hub motor,so the bike becomes all wheel drive vehicle(2x2).

[@swtexan6582]

I wish I would of thought of that, I literally just ordered my kit last night...

[@Jed-cy7tc]

Does it come with the nuts for the wheel?

[@hourlay9556]

Works well but bowl is really shallow.

[@TheEnixx]

the sensor is on the wrong side comes on the side of the chains

[@JesusOurKing]

I love watching these whilst my ebike is always broken down 😭

[@mattderlly7471]

Do you have this kit?

[@JesusOurKing]

@@mattderlly7471 no I got this kit here from www.theebikemotor.com/productshow.asp?ArticleID=1352&title=Theebikemotor%2048V1000W%20Electric%20Bicycle%20E%20Bike%20Hub%20Motor%20Kit%20+%20LCD+Disc%20Brake&bigclassname=Products&smallclassname=BLDC%20Motors%20&%20Conversion%20Kits But now I'm getting Error 7 message. I believe it's the controller so I ordered a another one to test with from AliExpress for like $15

[@Donmindme112]

Bruh y does ur battery connectors actually connect

[@dougmartin8495]

How can I make it further and FASTER???

[@ebikeling1249]

Hi Doug, Kindly read the article below: ebikeling.com/blogs/news/battery-range-on-electric-bicycles Thanks,

[@torino2111]

When I increase the 7 to 8 speed, Rd hits the ebike hub plate. What should I do

[@ebikeling1249]

Hi, Please make sure that your chain is compatible with 8 Speed gears.

[@Phil8sheo]

Will this kit work for any 700C bike? I have a trek bontrager 7.3 fx and looking to convert it.

[@KingNeptune151]

Same, any answers?

[@Phil8sheo]

@@KingNeptune151 I sure would like to know before spending the money.

[@lonewolf2156]

David Stoler Most likely just specify the wheel size I’m sure you can find them

[@arlenes.4590]

Controllers need ventilation as hey gt hot.

[@WM5000-ek9nk]

It has air ventilation... But the main problem is the controller is very big... I can't find smaller

[@eazypeazy7743]

Hi. Would this conversion work for a single speed bike? I'm just concerned because my Bikes casssettes and freewheels looks different from every other bike that I seen that has done this conversion. If anyone can help me out, I'd greatly appreciate it.

[@pauls5745]

yes, it can be installed but as is, you wouldn't be shifting gears. just match up the chain to the gear you want to use. you might need to add/remove links. there are rear hub kits for single speed tho, too. very similar...

[@jegannivas7105]

Can u suggest which motor will be good for motorbikes, hub or central mount motors. For bikes have 120 as top speed.

[@egoat5082]

qs 273 hub

[@walterconcrete5017]

Sure glad I didn’t get a piece of junk looking controller like that, I watched the video to try to figure out what the narrow (about 1/8”wide,color coded red on the plug with two tiny female receptacles for prongs,the wire is about 6”long). I don’t know what it does.

[@startcherif]

Very nice video,thanks for your explanation

[@ryanthecoder2114]

The sensor on the bottom bracket isn't needed though right? - I could just use the throttle?

[@egoat5082]

yup, thats what I do

[@mangodwins6328]

52 could blow up a 48 volt so I heard stay the same to b safe

[@shannonjenkins8482]

Great Value, quality bike

[@wegowifi5615]

Where to buy it and how much with thanks

[@ebikeling]

Hi, please visit ebikeling.com to check every information you need or to purchase an ebike conversion kit! You may also reach us through the website if you have any questions.

[@thegee-tahguy4877]

Do they make a fat bike wheel 26x4.0?

[@egoat5082]

you can find one on aaliexpress

[@pauls5745]

have a peek at this vid - kzbin.info/www/bejne/naXQl3-KnpKlodE

[@mohebazer2936]

is it available in size 29 inch? and how can i get it in egypt?

[@ebikeling]

Hi, Moheb...You can get more information about the size in the web page www.ebikeling.com. You can order it and shipped to any country you want please see the comments on ebikeling.com/pages/faq and see the explanation under "Do you ship to X country?"

[@Fellafoe69]

What wind motor is this 9C

[@pmc9108]

what is different twist and thumb.thank you

[@egoat5082]

twist is good if you want the full motorcycle style but you have to remove your old grip. Thumb goes next to your grip and you just flick it with your thumb.

[@Dsole1217]

what is that bag for the controller that you used called?

[@ebikeling1249]

It's a bag the customer used for controller. You can find it on Amazon or eBay. Thanks,

[@Riley_1955]

It should be called needless because controllers can get hot and need ventilation.....He should have installed it exactly the way he did but left off the cover.

[@mochadust9]

Great video! Is the motor loud? I'm almost done putting mine together. It's the same rear hub ebikeling motor.

[@zacharys1502]

No Should not be loud at all

[@belanagy5595]

Just found this video, good job! I'm about to receive my rear hub kit, so waiting to install it. So I have 2 questions. 1) Really liked your air compressor, what brand is this, where did you buy it from? It's really cool. 2) What application did you use to capture speed and then show on the bottom left of the screen - when showing test ride? Thanks ;-)

[@pauls5745]

why would an obvious ebike be confiscated because of a thumb throttle? you could get pulled over if you're doing like 25+ mph/40kmh... that'd be if you're over-powered for legal limits,. actually I prefer thumb to a twist throttle.

[@johnlucas604]

What if your bike don’t have disc brakes in the rear

[@ebikeling1249]

Hi John, You do not have to use disk brakes, it's totally for your own safety. The motor operates even without brakes.

[@johnlucas604]

My bike has brakes jus regular brakes

[@ebikeling1249]

@@johnlucas604 That's totally fine. You can keep using your own brake levers and brake system. The ones included in the kit are optional.

[@forevercomputing]

The rim has a black band on it and is unpainted. The black band is a wear indicator. Once this fades, the rim must be replaced. The motor can be re-laced to another rim. In the video, he said it will support disc and rim brakes. So, you are covered.

[@kr7799]

What is the O.L.D. of this motor hub? I cannot find a straight answer to this. I asked the seller they said 135mm but on your first ebay link it says 132mm

[@forevercomputing]

There is a 142mm I believe. Steel frames can be "adjusted" but alloy will need special care. If it is a 132, then spacers will be needed.

[@deesmacks4345]

which gauge/lcd will work with a 52v battery?

[@egoat5082]

sw900

[@elnatani6059]

What was the top speed again in miles

[@MrCarlRobinson]

Elnatan I 50kph is about 30mph

[@longshot4484]

@@MrCarlRobinson sorry what about the price in $

[@egoat5082]

@@longshot4484 this kit is 600. I made an ebike for much cheaper with a kit off aliexpress and it can go 45 mph. The kit was only 250 and the battery was 52v 17.5 ah for 400

[@pauls5745]

at 0:51 , that looked like a cassette, not a freewheel

[@dwaipayandattaroy9801]

I want socket Jamclamp and pull with legs, my power more than bikes daddling thrust, more controlled and efficient though it's hop not

[@WM5000-ek9nk]

How much is the range

[@ebikeling]

Range depends on the power of the kit you use and capacity of your battery. On average the range is - 21 miles (Electric only) 42 miles (Pedal Assist)

[@ebikeling]

you can have more information on www.ebikeling.com

[@martinsinclair55]

What is a torque arm?

[@forevercomputing]

In this scenario, it might just be a brace to keep everything where it is supposed to be.

[@pauls5745]

esp with high power rear wheel motors, the axle can walk after a bit, so a torque arm is extra defense

[@MikeKleinsteuber]

Nicely done

[@stoneyswolf]

Does anybody know a link to a 20" wheel and hub that will fit an older bmx frame. Preferably 3000watts or more.

[@cristianstefanmanu3897]

Search on aliexpress

[@alexandercruz3446]

China or US made? How much? Available in Amazon or Alibaba? Tnx

[@awsaldulaimi9137]

available on ebay

[@l3utterfish]

How do I attach the battery if I dont have the water holes?

[@georgewashington8652]

Search electrical conduit hangers. Use the one closest to the size of your down tube and bolt the holder to that.

[@denniswilson6851]

I used a "nut set" tool, (smile.amazon.com/Muzata-Riveter-Thread-Riveting-Included/dp/B01M59GTH8/) they are threaded rivets basically, just drill a hole insert the threaded rivet and use the threaded rivet tool to set it in the hole, now you have a place to screw! (or three with three nut rivets).

[@Dsole1217]

does the battery come with the XT60H battery connector?

[@ebikeling1249]

Hi, It depends on. Our batteries come with XT60H connector.

[@rapidburrito]

I'd love to get ahold of one of these 1200 watt or better kits! I can't find a prebuilt that I actually want/can afford!🌯🌯🌯🌯🌯

[@kopazwashere]

Prebuilts are waste of money and cost a fuckton to fix

[@sqwidink1]

I want a Trek Rail ebike, but too expensive right now 🏇

[@maxmilbredes897]

Can i use asi bac 8000 on this?

[@egoat5082]

get a more powerful motor like a qs 205 or a qs 273. On this youll blow out the coils.

[@sanesaint8725]

Get a twist trottle, way better and you don't have to hook up all that stuff you don't even have to pedal get a good battery that's why they called the ebikes batteries last up to two to three years so let's say two years without pedaling

[@KingNeptune151]

Works with v brakes??

[@egoat5082]

yes

[@donaldjames6811]

Electric bike is powered by food whilst preparing the speed going high and low anyone know what the problem please let me know??

[@egoat5082]

what are you trying to say

[@gabedarrett1301]

He's probably drunk

[@egoat5082]

@@gabedarrett1301 ikr