Any special tricks to get midpipe to seat fully to the pipe that leads to muffler? Lightly sand any rust and use a good lubricant?
@dannyjohnsonsgarage8 ай бұрын
I would lift/ support the mid pipe slightly with a jack while you bolt it up, and use some copper gasket maker if needed kzbin.info/www/bejne/jJXQpGCBiNV8htEsi=N2UvCq_g2dO0K2B4
@jeremyhuang13 Жыл бұрын
I remember this clear from years ago. So my question for you is which do you prefer in terms of sound? H or X? I am thinking H pipe for me
@dannyjohnsonsgarage Жыл бұрын
I have the H on my cobra and it avoids the nasty rasp at 2,500 rpm, and more of a muscle car sound. But I think the x is more raw in the end. Depends on what you’re looking for
@jeremyhuang13 Жыл бұрын
@@dannyjohnsonsgarage I have Borla Atak (I remember your white GT having the ORX with Borla Stinger from a few years back). I think Borla Atak goes well with ORH. I have to find a clip do someone with it. It sounds so mean.
@jeremyhuang13 Жыл бұрын
@@dannyjohnsonsgarage here it is. kzbin.info/www/bejne/fGK1iaWPbr1mqq8 I am a firm believer that 99-04 GT 2V need Borla Atak while 4V should go with stinger
@2vgod4604 жыл бұрын
I had a off road h pipe installed had a question does your driver side sit low? Not sure if the pipes are just shit or that’s how they sit, the shop says that’s how it’s suppose to be cause that’s the way the pipes sit.. I have barley any clearance since I’m lowered lol
@dannyjohnsonsgarage4 жыл бұрын
S gill Is it a one piece kit, or did it go together in sections? It may depend on the brand
@2vgod4604 жыл бұрын
Danny Johnson’s Garage hey bro, it came in two parts but it was split at the h pipe section
@dannyjohnsonsgarage4 жыл бұрын
S gill if everything is tight and it’s not leaking, then that’s probably just how it’s built. my SLP X Pipe hangs down really low compared to other X Pipe‘s. It just depends on the manufacture sometimes
@andwolo39213 жыл бұрын
I am installing a X pipe and cat back on my Mach one from Bassani. (With cats) The question is do I need to get a tune after removing my stock exhaust system? Just wondering your thoughts
@dannyjohnsonsgarage3 жыл бұрын
If you still have cats (high flow) it may or may not trigger the rear o2 sensors when they notice less filtering. It won’t hurt the car, but if you get a check engine light you will want to look into mil eliminators or a tune that turns the rear 02 sensors off. The car may also run a little more rich, but it won’t need a tune unless it’s completely catless. My GT runs fun without any, but my mach 1 turned into a dog without the tune for o/r.
@dannyjohnsonsgarage3 жыл бұрын
Turning off rear sensors (Ive heard of some companies not making it an option anymore on new scanners) kzbin.info/www/bejne/rGqtoWitptWSl5o
@dannyjohnsonsgarage3 жыл бұрын
MIL eliminators kzbin.info/www/bejne/qYC5ZXite5x1rLc
@andwolo39213 жыл бұрын
Thank you for your info, Looks like I have a few ways to go with us.
@azizshavershian20653 жыл бұрын
Good morning sir - would a brand new gasket, the copper ultra gasket (or both) be optimal? I just installed an OR XPipe on my 98 Cobra and noticed the passenger exhaust flange is smoking now. Thinking perhaps the gasket was damaged during install so just ordered a new one from Ford for $8 :)
@dannyjohnsonsgarage3 жыл бұрын
I do both for better luck, especially for aftermarket kits
@azizshavershian20653 жыл бұрын
@@dannyjohnsonsgarage Thank you!
@Eeropolvasti7 жыл бұрын
Good Job! Question: why you changed X-pipe to X-pipe??/ And what is bolt/nut size X-pipe going to exhaust manifold?/headers?? Thanks
@dannyjohnsonsgarage7 жыл бұрын
Eero Laukkanen I was changing out the x pipe to another x pipe that has a "bung" (port that accepts a wideband sensor). The nut for the manifold bolts should be 15mm and you may not be able to fit a deep socket in there, so you can go to a 1/2 drive size socket that is deep enough and will act like a deep socket.
@Eeropolvasti7 жыл бұрын
OK, thanks. Still don't know, what "bung" is, never heard ;o), by the way, would that Xpipe fit into my 2004, 3.8 litre V6?? You want to sell it to me "cheap"??=) Thanks
@dannyjohnsonsgarage7 жыл бұрын
Eero Laukkanen sorry, I already sold it. I'm not sure it would match up anyway. The "bung" is a threaded area just like the O2 sensor port.
@Eeropolvasti7 жыл бұрын
Where is that "threaded area""?? I just know there is 4 O2 sensors?? By the way, how much you sold it for?/;o)
@dannyjohnsonsgarage7 жыл бұрын
Eero Laukkanen sold it for $300. It was a high quality pipe. Here is info on the bung kzbin.info/www/bejne/e32paK2Opb2mo5o
@lavergadezambada8 жыл бұрын
should do one on the stock h pipe. recommend using a swivel socket and 3/8 extensions.
@GameOver3217 жыл бұрын
Great vid! I was wandering. I have a mint Bassani O/R Xpipe from my 97 cobra in my garage. Will that fit my 03 cobra?
@dannyjohnsonsgarage7 жыл бұрын
Don Johnson I recall trying to put a 96-98 mid pipe on my 03 Mach 1 at one point and it didn't quite match up. It may depend on the manufacture if they made it work on all, but I would say probably not
@Yogazies3 жыл бұрын
Is there a reason you don't unplug the O2 sensors to install them?
@dannyjohnsonsgarage3 жыл бұрын
You can, but they are pretty high up in there, so they can be hard to reach the connection. Either way works
@MrTrollus10 жыл бұрын
Nice, looks like somebody had an inspection coming up. I'm gonna have to do the same to mine unless I can find someone not to notice my lack of cats
@robb1503310 жыл бұрын
Great video. Thanks for sharing. Question-when a midpope is installed for the first time, does the flanged outlet match up and align with stock piping? Thanks
@dannyjohnsonsgarage10 жыл бұрын
Yes, for the most part it does match right up. It depends on the quality of the kit and a few things. For example, the SLP x pipe I removed in this video separates into 3 pieces. It makes it difficult to get all angles correct and not have it leak at any of the joints. The SLP set up does give you more play as you can add or subtract a few inches here and there. The magnaflow x pipe I installed in it's place was one piece, so it doesn't let you give and take. The magnaflow pipe matches up closer, it is less likely to leak, but it forces pieces to match up how it comes. It actually sucked my exhaust tips in about an inch since it was shorter. Just make sure you are not buying a "shorty" x or h pipe that is meant for headers
@robb1503310 жыл бұрын
Thanks. It will be an off/road down-pipe, ProChamber mid-pipe. Connected to stock headers. I am adding new hi-flow cats, and 4 new O2 sensors and MIL eliminator if needed. I will cut in the hi-flow cats, so it will be in about 6 pieces. I'm worried about the width between the two pipes on the outlet of midpipe which is identical to your X pipe shown in picture. Whether or not the stock muffler piping is going to match up. Thanks
@brycetaylor30779 жыл бұрын
I think I met you today in the mall parking lot. I had the black Shelby GT500 that parked right by you.
@dannyjohnsonsgarage9 жыл бұрын
My friend who also has a Mach 1 works there. It was probably him. You need to join our Facebook club if you are from the area. Add me as a friend if you have Facebook. Danny Johnson
@giomedina59609 жыл бұрын
Sweet vid Definitely some tips I'll be using while I'm installing my h-pipe Thanks
@dylanfinnegan67127 жыл бұрын
hey I just purchased a used x pipe for my 2000 Mustang GT and it didn't come with any hardware do I need to purchase hardware before I do this or do I just use my factory stuff? my exhaust in stock except for 2 mufflers I had a shop weld in. thank you!
@dannyjohnsonsgarage7 жыл бұрын
Dylan Finnegan you may not be able to use factory hardware because it has studs that appear to be welded in. You can try, but plan to make a trip to the hardware store
@dylanfinnegan67127 жыл бұрын
Scrun Johnson do you happen to know how long bolts are that I need?
@dannyjohnsonsgarage7 жыл бұрын
Dylan Finnegan about 4" watch at 3:20 and you'll see them
@dylanfinnegan67127 жыл бұрын
awesome thank you so much for your help! what grade bolts would you recommend?
@jamesa62724 жыл бұрын
I couldn’t get my o2 sensors out!
@dannyjohnsonsgarage4 жыл бұрын
James A That’s too bad! You can try to disconnect the sensor and work on it once it’s removed
@jamesa62724 жыл бұрын
Danny Johnson they came out easy the first time I took the stock mid pipe off. The o2 sensor socket I was using was flexing and slipping. I will try a wrench or another socket.
@GameOver3217 жыл бұрын
was the mid pipe you tried from a 4v or 2v?
@dannyjohnsonsgarage7 жыл бұрын
Don Johnson 2V to 2V. I've put 99-04 2V on my Mach 1 without w problem and a lot of companies advertise they fit "99-04 GT, Mach 1, and cobra." In fact, the h pipe on my Cobra was once on a 2000 GT.
@jasont19176 жыл бұрын
Thank you!
@dannyjohnsonsgarage6 жыл бұрын
Glad you enjoyed the video. Thanks for watching!
@marine0331inf10 жыл бұрын
Does the mach have a kb on it?
@dannyjohnsonsgarage10 жыл бұрын
No, my Cobra has a whipple and the Mach 1 is full bolt ons + the 4.10s and built rear (install vids on my channel)
@marine0331inf10 жыл бұрын
Scrun Johnson nice. My buddy had a 03 cobra which was a blast. Since then I wanted to put a kb on my car. Right now its bolt ons on a built motor with 3.73's.
@SuperJoooe7 жыл бұрын
lol..the pegs eh!!!! lmaowhen the teacher calls studs pegs!!
@brycetaylor30779 жыл бұрын
If you want you can add me, I couldn't find you. Bryce Davenport Mines a picture of me and a girl with glasses.