Struts and Shocks install Ford Mustang 1994-2004

  Рет қаралды 66,997

Danny Johnson’s Garage

Danny Johnson’s Garage

Күн бұрын

Пікірлер: 127
@777Trolly
@777Trolly 4 жыл бұрын
Good video - thanks. One piece of information, according to my 1997 Mustang FSM, the torques are as follows for the rear shocks: Upper nut = 25-33 lb-ft, lower nut = 57-75 lb-ft and quad shock nut = 57-75 lb-ft.
@wastelander89
@wastelander89 11 ай бұрын
I installed new rear struts on my 03 mustang and omg .its like a brand new car .finally no more bouncing all over the road and dangerous bose diving under braking.i installed fcs auto struts from rock auto and it feels like a brand new car. Hanldes like a dream . The brakes feel better and no more bouncing 20 times after each tint bump.and finally safe in the rain. My whole life I thought tires made the big difference but.. have bad shocks or struts is so much of the handling
@mariomendoza8300
@mariomendoza8300 9 ай бұрын
This video is better than the Haynes one... thanks man!
@ThePsvan
@ThePsvan Жыл бұрын
3:03 I found it way easier to loosen the big strut nut with the front of the car on jackstands under the frame rails and the front wheels off the ground, with the struts still bolted to the steering knuckles. This has the weight of the wheels and control arms etc being held up by the strut. The rubber in the strut mount compresses from the weight and makes the nut way easier to loosen, or tighten, and the whole assembly less likely to rotate.
@dannyjohnsonsgarage
@dannyjohnsonsgarage Жыл бұрын
I’ll have to try that next time
@ThePsvan
@ThePsvan Жыл бұрын
@@dannyjohnsonsgarage Yeah, one of mine came loose with the large screwdriver technique, but the other one was so stuck I ended up cutting the top end of the strut off. Only discovered the drooping suspension trick afterwards.
@maxamillion4223
@maxamillion4223 Жыл бұрын
Good info
@675Brece
@675Brece 4 жыл бұрын
Just had new bearings and tie rods installed on my V6. I'm going to try the struts and shocks myself. Thanks! Very informative video.
@wastelander89
@wastelander89 11 ай бұрын
I did this the hard way i squeezed under the car and didnt jack it up. When installing the back struts i had my sister use black electric tape to keep the strut closed so i could install it with out struggling to compress the shock. But im so happy i put new struts in feels like a brand new car. I got them from rock auto they were oem quality and rides great. The exhaust in my face made it difficult but i luckily got it done
@cheetodonalddump7078
@cheetodonalddump7078 8 ай бұрын
Great video. This will help get this free mustang running smoother
@bradvaughan3658
@bradvaughan3658 4 жыл бұрын
Great video. Probably the most informative I’ve seen and I’ve seen several.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
Thanks 🙏🏼
@Lethal_Venom
@Lethal_Venom 4 жыл бұрын
I did this on my 94 Cobra when installing the strange 10 way adjustables on the front / rear. Great video.
@DisgruntledVet8893
@DisgruntledVet8893 4 жыл бұрын
Awesome video, I think I’ll be doing this when I put in the lowering springs. Also I’ll be changing the brake pads and rotors.
@bap7929
@bap7929 4 жыл бұрын
Just did this with my GT w/Koni oranges and installed an eibach pro kit. Didn’t lower it enough to need caster plates but I did install the caster bolts.
@TurboTurdBurglar
@TurboTurdBurglar 4 жыл бұрын
Hows the ride quality with the oranges
@bap7929
@bap7929 4 жыл бұрын
@@TurboTurdBurglar At first the handling was improved and comfort was slightly decreased. Biggest difference was the body roll being significantly reduced. Unfortunately my new spring isolators disintegrated within weeks and it’s a rough ride right now.
@TurboTurdBurglar
@TurboTurdBurglar 4 жыл бұрын
Ba P ahh gotcha. I really wana get the oranges because there affordable but i had bilsteins on my last mustang and it rode so nice so im not sure if i should spend the extra 300 on bilsteins again. Or just cheap out and oranges. Also i ran no isolators
@juanpedraza563
@juanpedraza563 3 жыл бұрын
Awesome video man! I could watch these videos all day 😊
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
I’m glad you enjoy them!
@riceetr1260
@riceetr1260 4 жыл бұрын
Great video Danny this is a must for the cobra as the past owner put eibach pro springs but left factory shocks... only 57k miles but I’m sure the car will ride and handle better with shocks and struts
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
Rice ETR Just wanted to mention the kit may be different if your 99-04 cobra with IRS in case you have that.
@thesupremejuice
@thesupremejuice 11 ай бұрын
now this is a good walkthrough
@rv929
@rv929 4 жыл бұрын
Great video. I always watch your channel before I work on my 96 GT. Keep those good videos coming
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
Thank you! You got it. 700 videos and counting
@kmdesantis
@kmdesantis 2 жыл бұрын
What an excellent how to video, exactly what I was looking for
@angelgjr1999
@angelgjr1999 2 жыл бұрын
Don’t forget quad shocks. Helps get differential from “hopping”.
@3SPCOD
@3SPCOD 3 жыл бұрын
Your videos are easy to watch thank you
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
Thank you. I’m glad you enjoy them 🙏🏼
@davieboy1970
@davieboy1970 3 ай бұрын
To take the strut bolts out you just use your impact with the socket on the head of the bolt and then use an open and wrench to hold the nuts in place just spin them right off. And then do the same thing to tighten them back up when you get the new strut on that would’ve saved you a lot of time.
@babyjuju4411145
@babyjuju4411145 4 жыл бұрын
Very thorough video. Excellent step by step.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
Thanks! I’m glad you enjoyed it! See my others like it in this playlist kzbin.info/aero/PLIjr-uSYDZi7hBrphoRniyYjb707PpPTu
@littlewolf947
@littlewolf947 12 сағат бұрын
Great video danny..did you notice any alignment changes after replacing front struts?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 12 сағат бұрын
I did not, but it is always good to have it checked after a suspension repair
@ericbickett4104
@ericbickett4104 3 жыл бұрын
Really informative and great video with commentary! Thanks for the share!
@supernt100
@supernt100 4 жыл бұрын
I did this and now there is a bad groan and squeak ... do I need new bushings and a new tube ?
@1siksn95
@1siksn95 4 жыл бұрын
I have hotchkiss performance on mine and they’re great. Love watching videos like this, nice upload!
@aiidum3551
@aiidum3551 Жыл бұрын
This was insanely helpful thank you so much!
@yannyfrag
@yannyfrag 4 жыл бұрын
Just another awesome video. Thank you for the video, I appreciate you doing all the videos you do.
@904Saleen
@904Saleen 4 жыл бұрын
Danny, would you happen to know where I can find a replacement bushing like the one you mentioned at 4:23? The one that is under the dust cover? I pulled off my OEM Saleen Racecraft Struts as they are toast and found that neither of my fronts have these. I'm going to assume my rears don't either. Any ideas? I'm keeping the stock Saleen Springs but pairing them with a set of KYB struts and shocks.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
Here is a kit you can consider www.amazon.com/gp/product/B009DJVO5Y/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=2004047-20&creative=9325&linkCode=as2&creativeASIN=B009DJVO5Y&linkId=e7b86da0f614bb4fdeb4f621441d6d7a
@djglennb736
@djglennb736 4 жыл бұрын
What’s the link for the rear bushings? I clicked on one in description but it says it’s for the fronts
@shafferjoe1962
@shafferjoe1962 Жыл бұрын
Thank you for the video. I discovered I have a frozen right front strut that does not move. So it is over working the other 3 shocks. Do you like the Tokico shocks you bought?
@dannyjohnsonsgarage
@dannyjohnsonsgarage Жыл бұрын
They are great. Hard to find now
@ultimatedistractionz9113
@ultimatedistractionz9113 2 жыл бұрын
Is there another video on how to do it without removing the tire
@dongkapuyawn5107
@dongkapuyawn5107 3 жыл бұрын
Do you have a video on the removal or installation of the 'drivetrain damper' ?
@kingdomculture5743
@kingdomculture5743 Жыл бұрын
I think I can do this! Thanks for this video!
@victornaja7927
@victornaja7927 Ай бұрын
i cant find this tokico shocks can you help me where to get them
@steven7297
@steven7297 2 жыл бұрын
I cannot find rear springs for 2003 rear , and cannot find driver side door , pls helppp
@dorkydarell4073
@dorkydarell4073 2 жыл бұрын
Great video sir 👍, detailed and clear!
@MudMonsterRacing4
@MudMonsterRacing4 4 жыл бұрын
Did u have to get an alignment afterwards?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
It’s definitely good to have it checked. Mine seemed to drive about the same, but I’m planning on doing wheel bearings and tie rods in the future so I have older tires up front for now.
@scottyprice339
@scottyprice339 7 ай бұрын
Man you are awesome! Thank you SO much!!!!!
@sandmansimms5704
@sandmansimms5704 4 ай бұрын
for shocks you can torque to specs while they're being held up by the jack correct?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 ай бұрын
I would also verify them once the car is down since the weight pushes the struts up and they will likely be loose again
@sandmansimms5704
@sandmansimms5704 4 ай бұрын
@@dannyjohnsonsgarage so that's a yes to my question I guess LOL? When I verify once the car is down I guess I can pretty much go ahead and put the back tires on ramps so I can verify
@sandmansimms5704
@sandmansimms5704 4 ай бұрын
Also Danny so where you put your jack stand inside anywhere in that area and it can be placed anywhere in that area? I was always going a little further back on that what looks kind of like an arm where it's kind of like a l-shaped or kind of round L that looks very sturdy and secure and I was always putting it back there. But if anywhere in that area including where you put the jack is nice and secure as well that's definitely easier to not have to go all the way up a little higher just to get all the way back there too
@DaSaintDemon
@DaSaintDemon 6 ай бұрын
Man i want to make my 2004 mustang higher. I live in a place with reaaaally big speed bumps (bus worthy) and a lot of dirt roads. So basically i when i drive my car hit underneath in most places if in not careful. I really need some advices in how to lift my car to be kinda off-road
@Palomino488
@Palomino488 Жыл бұрын
Great video! Could you make a detailed video of installing a SR Performance Strut Tower Brace on your GT? I’m about to take on installing one of those braces on my 2002 Mustang GT and could use a good video for reference.
@dannyjohnsonsgarage
@dannyjohnsonsgarage Жыл бұрын
I will see if my brother has a brace laying around that I can install. I don’t have one at the moment
@irvinggonzalez9185
@irvinggonzalez9185 Жыл бұрын
I couldn't find a tokico set, I ordered yellow koni, greetings from north ut
@dannyjohnsonsgarage
@dannyjohnsonsgarage Жыл бұрын
I don’t think they are made anymore
@irvinggonzalez9185
@irvinggonzalez9185 Жыл бұрын
​@@dannyjohnsonsgarageYes, I only found Tokico blue front, not the entire set.
@matthewpisano5549
@matthewpisano5549 6 ай бұрын
what struts are they? I have a 2000mustang gt
@dannyjohnsonsgarage
@dannyjohnsonsgarage 6 ай бұрын
These are the Tokico blues, but I’m not sure they make them.
@sandmansimms5704
@sandmansimms5704 3 жыл бұрын
94 cobra trying to get the top strut nut off and having some trouble. Hopefully the oil will penetrate it enough to loosen eventually SMH
@kmdesantis
@kmdesantis 2 жыл бұрын
What size Jack stands are those
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
3 Ton (6,000 pound) jack stands amzn.to/3P72mtR
@lukyanrosselli
@lukyanrosselli 11 ай бұрын
Thanks Again Bro! 🙌🙌
@peteschurz2137
@peteschurz2137 2 жыл бұрын
Awesome video
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
Thanks! Check out my playlist for more like it Mustang Maintenance and repair kzbin.info/aero/PLIjr-uSYDZi7hBrphoRniyYjb707PpPTu
@nostradamus4828
@nostradamus4828 Жыл бұрын
Thank you 👌
@dannyjohnsonsgarage
@dannyjohnsonsgarage Жыл бұрын
You're welcome!
@steven7297
@steven7297 2 жыл бұрын
Are the spring the same for a 2004 4.6 mustang as for the v6 I plan on getting rear springs and someone said both parts are the same
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
The front springs are different for the heavier V8. The rears should work because I put a 8.8” in the rear of my V6 mustang
@ultimatedistractionz9113
@ultimatedistractionz9113 2 жыл бұрын
What tool sizes is he using?
@1alex1311
@1alex1311 4 жыл бұрын
Hey Danny is the high pressure ps line from the ps pump to the hydro boost, the same on the mach and cobra?
@caseindaplace
@caseindaplace Жыл бұрын
Danny I have a 2003 Cobra and the driver rear shock bushing needs replacement as it bounces freely and taps on bumps Would the process be similar before I go tearing into it?
@dannyjohnsonsgarage
@dannyjohnsonsgarage Жыл бұрын
Yes, same process. It helps to gently push up on the strut to get it into place to put the bolt through the control arm as you’ll see kzbin.info/www/bejne/Z3OYo4Ofe8h1fsU
@caseindaplace
@caseindaplace Жыл бұрын
@@dannyjohnsonsgarage thank you, I saw the part you mentioned when the Jack. Going to tackle it today once the heat index of 115° drops a little
@caseindaplace
@caseindaplace Жыл бұрын
@@dannyjohnsonsgarage the lower “hat” on the shock on the underside of the wheel arch, is that supposed to be upwards like a bowl shape to hold the bushing (opposite of the trunk hat) ?
@scuevas7
@scuevas7 2 жыл бұрын
Good day do you thing it's necessary to replace the quad shock and does a 2004 v6 have quad shocks or only the higher end models?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
They are only on V8 models and not necessary to replace in my opinion
@scuevas7
@scuevas7 2 жыл бұрын
@@dannyjohnsonsgarage ok nice does the v6 have the bolts for it I have a GT rear diff and I'm going to swap it or is all the bolts on the diff itself thanks.
@donphillips599
@donphillips599 5 ай бұрын
Does the front have springs ?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 5 ай бұрын
The springs are separate (they are not coil over strut design unless they were changed at some point).
@brianshoemaker7704
@brianshoemaker7704 10 ай бұрын
Maybe use wrench and impact screw driver, prop wrench against something so you have both hands for impact screwdriver
@jm92gt03gt
@jm92gt03gt 2 жыл бұрын
What about the quad shocks, should they be replaced or do they not go bad?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
Yes, they should also be replaced.
@jarmll
@jarmll 4 жыл бұрын
could you have used Mach 1 replacement units instead of GT? Are they better or different?
@Fr3sh-Kush
@Fr3sh-Kush 2 жыл бұрын
Would it be possible to use an impact from beginnning to end? To get them loose from the strut tower
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
Yes, but be careful not to break the nuts. I showed the traditional method since a lot of people don’t have access to one.
@Fr3sh-Kush
@Fr3sh-Kush 2 жыл бұрын
@@dannyjohnsonsgarage thanks man. Youve been a great help on alot of questions ive had in the past. Thank you very much
@Fr3sh-Kush
@Fr3sh-Kush 2 жыл бұрын
@@dannyjohnsonsgarage hey man its me again. Bought some Bilstien b6 performanc rear shocka for 2002 GT. the shocks came with their own bushing. A tan colored one. Should i use it? Or do i need the same style as the one already on the car?? Im doing this job for the first time tomorrow. Any tips help. Thanks
@dannyjohnsonsgarage
@dannyjohnsonsgarage 2 жыл бұрын
@@Fr3sh-Kush either should be fine. I’ve used stock ones if the new ones give me any kind of fitment problems. Just make sure bushings are slightly squished but not too tight on the rear. If you have an impact gun it’s best for the front top strut nuts. Soak them in advance with pb blaster or liquid wrench
@Fr3sh-Kush
@Fr3sh-Kush 2 жыл бұрын
@@dannyjohnsonsgarage also is the process for changing rear quad shocks the same on GT as it is on cobras? Cant find any tutorials on GT cars specifically. Big thanks thoough man. You and alot of youtubers have taught me alot.
@warrenwaymack7366
@warrenwaymack7366 8 ай бұрын
Where and which brand did you go with thanks
@dannyjohnsonsgarage
@dannyjohnsonsgarage 8 ай бұрын
Tokico since the mach 1 and Bullitt came with that brand. Bilstien and others make them just as well
@brandonhancock6607
@brandonhancock6607 3 жыл бұрын
I cannot for the life of me get that nut off I've used a screwdriver I've used an air gun and I cannot f****** get it off any suggestions? Talking about the nut for the front shock.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
If you’re talking about the top nut and you have new struts to put on just cut the nut off with a grinder/dremel. It won’t be reused on the new struts
@mathieuconklin3146
@mathieuconklin3146 3 жыл бұрын
I am sure you figured it out by now, but I had the same problem. take off the 3 smaller nuts up top and you can remove the strut fully assembled. Then you can set it and orient it wherever you need it to get that damn nut off. Spray the crap out of it with penetrating oil.
@Prodiga1Son
@Prodiga1Son 3 жыл бұрын
Did rear now car slams down really hard almost like bottoming out. Any advice?
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
How about the fronts? If they aren’t replaced it’s like holding the back of the car firm and letting the front flop around
@Prodiga1Son
@Prodiga1Son 3 жыл бұрын
@@dannyjohnsonsgarage yes fronts were replaced same day thanks to this video
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
If they are the correct shocks for the car, I don’t know why it would be bottoming out unless they are bad
@manningyveseldon2604
@manningyveseldon2604 4 жыл бұрын
Great video
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
Thanks!
@davieboy1970
@davieboy1970 5 ай бұрын
For anybody out there that might have the same issue I did. I loosened that top nut as much as I could with my gun and a socket, but then the whole thing kept spinning. I tried using his technique here with the screwdriver and the wrench, but it would not work. Almost broke the tip of the screwdriver. Just took my grinder out with a cutting wheel and ended up just cutting the nut right off on both sides and then the whole thing fell out
@jamesa6272
@jamesa6272 3 жыл бұрын
Hey Danny how were these shocks and struts? If I can still get my hands on a set I’m going to install them. Any other shocks and struts brands you would suggest for a 97 vert gt? I’m staying away from koni strt and presently have Monroe sensatrac on it now and it floats over bumps. Feels like a jetski on rough roads
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
I really like these. They are doing well.
@jamesa6272
@jamesa6272 3 жыл бұрын
@@dannyjohnsonsgarage well I can’t find any hp’s or illumina shocks anywhere. I had to settle for koni strt :(. I had them in my lowered 03 And hated them. My 97 has stock springs so I’m hoping the konis will feel better with more of the travel than the 03.
@JaVvii3
@JaVvii3 4 жыл бұрын
Danny where can I buy those struts? Awesome video, it’s very helpful.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
I got them off ebay. You may have to google the two part numbers HB3140 and HE3723
@JaVvii3
@JaVvii3 4 жыл бұрын
Danny Johnson thank you because I could only find the front but not the rear. I’m about to look.
@khancross
@khancross Жыл бұрын
Easy! Thanks
@jacuzzitech
@jacuzzitech Жыл бұрын
Great
@joedq
@joedq 4 жыл бұрын
Very informative video. Thanks for sharing, I have to change the front struts on my 98 soon..
@3vReanimated
@3vReanimated 4 жыл бұрын
Easier way to get stock nuts off the stock shock: Hacksaw both the nut and shock stud.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 4 жыл бұрын
There are certainly easier ways, but I tend to stick to the more traditional when showing people ha ha
@charlesb.3116
@charlesb.3116 3 жыл бұрын
I have a 95 v6 don't know if struts were ever changed. Broke 2 large screw drivers and a chisel on this terrible slotted design. Ended up cutting the nuts off with a grinder.
@MrLafinest1
@MrLafinest1 3 жыл бұрын
I can not get my strut back on for the life of me.
@dannyjohnsonsgarage
@dannyjohnsonsgarage 3 жыл бұрын
It won’t go through the strut holes or what?
@MrLafinest1
@MrLafinest1 3 жыл бұрын
@@dannyjohnsonsgarage I'm a dumass I didn't extend the friggin thing out. Thanks for the reply
@josephribot2261
@josephribot2261 3 жыл бұрын
Great video.
How to Install Coilovers in Your Car
16:45
ChrisFix
Рет қаралды 4,4 МЛН
Mustang KONI STR.T Shock and Strut Kit 1994-2004 Installation
7:55
CJ Pony Parts
Рет қаралды 138 М.
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 158 МЛН
Cheerleader Transformation That Left Everyone Speechless! #shorts
00:27
Fabiosa Best Lifehacks
Рет қаралды 16 МЛН
REPLACING THE QUAD SHOCKS ON MY 444,000 MILE MUSTANG COBRA
10:02
Reynolds Rides
Рет қаралды 20 М.
Rebuilding Front End Suspension 1994-2004 Ford Mustang
13:32
Swan Can Fix It
Рет қаралды 32 М.
1994-2004 Mustang SR Performance Front Strut Review & Install
7:00
AmericanMuscle Mustang
Рет қаралды 13 М.
Front Strut Replacement - Ultimate Guide (Ford Mustang 1999-2004)
19:47
TutorialGenius.com
Рет қаралды 26 М.
HIDDEN FEATURE on ALL 1999-2004 MUSTANGS!!
6:38
Xander Meisman
Рет қаралды 330 М.
How To Replace Front Struts And Rear Shocks Ford Mustang
28:03
Jimthecarguy
Рет қаралды 89 М.
1994 - 2004 Mustang : Installing Lowering Springs
7:46
tko resto
Рет қаралды 136 М.