Anti-seize!!! Can preach enough to others to use anti-seize on the hub bearing and bolts.
@utuber29404 жыл бұрын
I see you like cats...I just subscribed..😀
@Wayne_Nero Жыл бұрын
Great video! I realized i needed a bigger hammer!! Also what is that white thing on your axel shaft?? Some kinda bushing?? I don’t have one and I am looking for the part in the service manual
@askme26693 ай бұрын
just ignore the sleeve that comes with the lower ball joint just like the snap ring if you cleaned rust from bottom seat of ball joint you will get snap ring on armature
@borntobewild846Ай бұрын
Had a question. Would it be a good idea to put some anti-sieze on the ball joints as you're pressing them in?
@BroncoSolid4 жыл бұрын
This feels familiar
@JeepSolid4 жыл бұрын
Haha! Yep
@rudybishop90894 жыл бұрын
Throw the ball joints in the frig overnight and a light bulb on the knuckle for an hour and the parts will fall in - good stuff from a mill valley 03 TJ and 93 XJ owner
@pujo28 Жыл бұрын
What are your thought on TRQ brand which is 1AAuto’s brand? I have a TJ and have to replace all the steering and suspension components. Thanks
@-_-John-_- Жыл бұрын
✅
@ponypwr Жыл бұрын
Best instructional dana 30 video ive found! Thanks brother!
@dominicsardina43243 жыл бұрын
Hello there I watch all you videos and they are so helpful I’m told I need an offset upper ball joint To get the wheel alignment correct because my YJ drifts to the right and they need more adjustment to correct the drift, my concern is when you pull the axle out does the 4wd vacuum coupling have any issue when you pull the axle out or putting it back in, please reply with your expert advise, thanks
@pujo28 Жыл бұрын
What r your thought on removing & replacing ball joints with an air hammer?
@MuzzleFlashTV2 жыл бұрын
Did you have any plastic pieces on the axle shafts? I’m hearing those are needed to align the shaft splines with the differential splines.
@mrsdoylespinniedoyle1956 Жыл бұрын
Thanks for the video. I wasn't sure whether to do top or bottom first (or if it matters) but it's nice to see it being done by an expert. Here's hoping that refitting is easier than removal was.....
@thomasgreen71133 жыл бұрын
Did you have trouble pressing in the upper ball joint because of the angle of the upper knuckle? I destroyed the boot on my first one.
@rogerheath43483 жыл бұрын
Thank you so much for this video. I have been fighting that snap ring and was wondering if I had done it incorrectly, or if the ball joint I purchased was incorrect. I didn't realize that those not slipping back on is a common issue.
@leskobrandon5384 жыл бұрын
De ja Vue?
@JeepSolid4 жыл бұрын
Yes sir, it is. I didn't cover the issue people have with the grease fitting very well when I did it last. So, I'm taking the old one down and re releasing it with better info 👍🏽
@froggerman443 жыл бұрын
If u use a splined ball joint, can a smooth ball joint be put in its place?
@LimonEllie4 жыл бұрын
Next time make sure you lineup the Cotter pin hole from front to back of the Jeep
@TheGoshood3 жыл бұрын
great video. most helpful.
@albertonevarez73923 жыл бұрын
Torque of the wheel hub nut please
@briandurham32733 жыл бұрын
Usually watch your videos. You explain everything in depth very well. Bringing my 93 YJ back alive out here on the coast of Oregon. Getting it ready for hunting season and it’s my daily driver. Some day like to meet ya to go wheeling. Anyways thanks man it helps a lot.
@JeepSolid3 жыл бұрын
Awesome! Thank you. I hope to arrange a meet up sometime soon..
@seanhuggins40863 жыл бұрын
Very well done, thank you
@bobbemoras93344 жыл бұрын
Snap ring on lower doesn't fit. 1 side is angled where the ball joint is pressed.
@rogerheath43483 жыл бұрын
I'm here watching this video for the exact same issue. Not sure what I'm doing wrong hoping that this video teaches me.
@antlese4 жыл бұрын
You make it look easy.
@dissociativecat74954 жыл бұрын
tootsies the real boss
@JeepSolid4 жыл бұрын
Haha! Yep
@dissociativecat74954 жыл бұрын
@@JeepSolid hope you're staying safe, you got PPE at work ? No shortages I hope
@JeepSolid4 жыл бұрын
Thanks. I am 👍🏼
@Fossildobber4 жыл бұрын
What is the white thing on the axle outside of the knuckle?
@thomasgreen71133 жыл бұрын
Axle shaft oil slinger. Quadratec carry this part.
@thomasgreen71133 жыл бұрын
Crown Automotive 83500201 Outer Axle Shaft Oil Slinger for 87-95 Jeep Wrangler YJ, 84-01 Cherokee XJ & 93-98 Grand Cherokee ZJ with Dana 30 Front Axle
@thomasgreen71133 жыл бұрын
Sorry this is the one you asked about.
@thomasgreen71133 жыл бұрын
Crown Automotive 4797769 Axle Shaft Inner Slinger for 90-95 Jeep Wrangler YJ, 90-96 Cherokee XJ & 93-96 Grand Cherokee ZJ with Dana 30 Front Axle - Plastic Material
@gordongman34234 жыл бұрын
Job well done..
@JeepSolid4 жыл бұрын
Thanks Gordon
@JoeRed3 жыл бұрын
Just wanted to say thanks, I fought with swapping my ball joints a few hours before I found your videos.