😂 Great video on “How to NOT install a barrel “……. Just as educational as a “ how to” though. 👍🏻
@kelpo845510 ай бұрын
Can you explain why?
@liggerstuxin15 ай бұрын
Yeah, what parts are you criticizing? The way he uses his torque wrench is my guess.
@chrisd5758Ай бұрын
@@liggerstuxin1he uses the completely wrong mounting tool. When installing barrels you should use a reaction style rod with a top fin to keep the upper from flexing or in this case he put all the tension on the take down pins as well as the barrel index pin. You can shear barrel index pins doing it the way he did in the video. Also he uses non milspec materials for the barrel extension and barrel nut all you need is some aeroshell thats milspec.
@timothydahlin5321 Жыл бұрын
Good deal on shootingsurplus for the vise block.
@RascalCatify Жыл бұрын
Out of curiosity, what is the reasoning behind torquing then backing the nut out until final torque? I get sneaking up on the final number, as is done a lot with working on cars, but never have backed something out to just torque it higher again.
@bigappa1862 Жыл бұрын
In layman terms... double torqueing accounts for bolt stretch and helps prevent it from coming loose/losing the desired torque spec. Think of it like a head bolt.
@joshuacruz404611 ай бұрын
It’s because it stretches
@wbrennan22533 ай бұрын
I did that when I installed mine. All the information I had read recommended it.
@wbrennan22533 ай бұрын
I had to thermal fit my barrel. I put the barrel in my freezer for a couple of hours then used a heat gun on the upper. I had maybe 10 seconds to get it seated.
@NeverGone233 ай бұрын
Seems a little excessive to seat a barrel. I wish I would have know this about the enhanced upper before I bought it. What brand of barrel do you have?
@chrisd5758Ай бұрын
Next time just get a block of wood on barrel and hammer it in, it'll go.
@Mongorat7 ай бұрын
How easy is it to remove that enhanced piece? Cos I have one M5 coming, but will put on a Hera IRS Quad on it instead.
@daverstewartjr57859 ай бұрын
You know that vice block is supposed to be 2 pieces. One piece goes into the upper and that vice block bolts to the piece into upper.
@dillionclayton21525 ай бұрын
Yep.... the other part is meant for applying torque to the barrel nut. I wouldn't copy this guy...
@dillionclayton21525 ай бұрын
Yeah.... the part that goes inside the upper is made for tightening the barrel nut. So you don't put unnecessary pressure on the aluminum upper receiver. The way he has it, is mostly used for cleaning or installing other accessories other than a barrel.
@DrunkSailor73Ай бұрын
do you have worry about timing the m5e1?
@chuekaothao632911 ай бұрын
LOL, some people using anti-seize while some other using loctite to lock it in place.
@Gunfighter510 ай бұрын
IT IS NOT RECOMMENDED TO USE LOCTITE !!! THE REASON FOR LOCTITE IS FOR WHEN YOU CANNOT TORQUE A PART!! NO REAL RIFLE MANUFACTURER WILL RECOMMEND USING IT AT THIS POINT. I laugh when people use blue loctite on gas block screws. That shit will turn to powder after one day of shooting. It would help if you had a high-temp thread locker like Rockset.
@BadDadio5 ай бұрын
Loctite LB 8060 is a thread lubricant and anti-sieze
@grandtheftavocado Жыл бұрын
Do you have to time the barrel nut to let the gas tube pass? Also do people bed and lap their barrel for these types of builds? I haven’t seen anyone do it on the enhanced M5 upper.
@jacobpayne1723 Жыл бұрын
I just did mine today and after torquing, there was a rib right in the middle and wouldn’t allow the gas tube to go past it. I shaved that one rib down with my Dremel to allow the gas tube to go in. I didn’t really see another way around it.
@grandtheftavocado Жыл бұрын
@@jacobpayne1723 Thanks man. I have used barrel shims before to time the nut, but I think I'll just dremel too
@MrPiimpslap8 ай бұрын
@@jacobpayne1723 lol, you could've shimmed or tighten a bit more, since the torque value for a barrel is a spread, and not an exact number.
@BuffaloSoldier-11 ай бұрын
How much is that vice and what brand ?
@John_Doe_69964 ай бұрын
But how to remove a barrel that is STUCK? Like really stuck…
@tollav3 ай бұрын
HEAT!! LOL That will more than likely work. Is the barrel nut stuck or is the barrel itself in the receiver?
@John_Doe_69963 ай бұрын
@@tollav the barrel itself was stuck in the receiver. I successfully got it out with no damage, used a pvc pipe through the receiver, and smacked the F out of it with a hammer. Tried the same thing with a wooden dowel at first, but the dowel kept breaking.
@marcmeadows61035 ай бұрын
Love how you skip important things
@toddbernal2183 Жыл бұрын
Technically you over torqued it. 65 foot pounds is measured at the head of the torque wrench. There's another 1-2 inches added to the length of the wrench. Torque multiplication means it's going to be more then 65 foot pounds. Will it matter, no absolutely not. Just sayin. You can find conversation formulas on line if you want to know what you torqued it to.
@user-gs6bi3pm5c Жыл бұрын
If the torque wrench is orthogonal to the crows foot, there is no need for math.
@lkazanov10 ай бұрын
90 degree to craw foot, is the torque at the wrench
@davidcampbell26617 ай бұрын
Your loc tite looks more like never seize
@BadDadio5 ай бұрын
Loctite LB 8060 is a thread lubricant and anti-sieze
@tobberfutooagain2628 Жыл бұрын
Its not a notch, it is a pin. The pin fits into the notch.