How to install door stepsills with LEDs | Honda Brio RS |

[@carbitstv]

Please don't forget to SUBSCRIBE HERE: kzbin.info/door/yL3Y7Y296BQk3jJrnnBIcA

[@renielrjs1545]

Mas mainam na tutorial tp kaysa sa babaklasin pa yung dome light assembly, mas maganda nga kung kumuha nalang ng power source sa fuse box at ground naman sa door switch thanks sa kaalamn lods

[@carbitstv]

welcome po and sana nakatulong po 😊👍

[@zaifkhann]

Good, Hi, what is the benefit of that two 10amp fuses? What if i install without fuses?

[@carbitstv]

those fuses serve to protect the wirings in case of electrical short. will prevent further damage.

[@zaifkhann]

@@carbitstv okay if i don't have that two fuse instrument, then how do i connect another 10amp fuse? before or after the original fuse? As I'm going to install door lights, welcome light

[@carbitstv]

@@zaifkhann the fuse tap that i used will allow you to put 2 fuses in 1 slot, 1 fuse will protect the original fuse, the 2nd will protect your welcome light. Fuse tap is the most efficient way to do it but make sure there's a fuse in between the original fuse and the welcome light

[@zaifkhann]

@@carbitstv okay last one, what amp of fuse should i use for welcome light? Should i use 2nd fuse same as the original fuse?

[@carbitstv]

@@zaifkhann same would be fine (10amp)

[@albertBausa-u2h]

Sir carbis baka meron ka pong alam pano tangalin ying dashboard trim yung grey na nakalinya sa airon at sa dashboard

[@carbitstv]

meron ako video, check nyo yung replacement ko ng instrument gauge ... tinaggal ko kasi dun yung center piece

[@jessgranada3241]

Sir ano advantage ng naka connect sa grounding ng door lock yung ground wire compared sa naaconnect sa car body? Thanks

[@carbitstv]

the way po naka setup yung door switch, ground ang dinidisconnect nya para mag ON lng yung stepsills pag bukas ang pinto. pag sa body lang natin ilalagay yung ground, always ON yung stepsills kahit sarado pinto

[@jessgranada3241]

@@carbitstv thank you sir, yung method mo gamitin ko, mag DIY install lang kasi ako. Very helpful, kesa mag tap sa mismong dome light.

[@carbitstv]

@@jessgranada3241 salamat. i remember sa old car ko (Hyundai Eon) wala syang door switch kaya sa dome din ako nag tap noon. malaki talaga advantage lalo pag may door switch, no need na maglatag ng mahabang wiring

[@sephir8244]

Sir ung skn n stepsill my ksma n wire black and red n my fuse un n b ikkabit ko s fuse box? Kaso ung black n ground hnd aabot s door

[@carbitstv]

hindi po kasama, if mejo maigsi po wires, pwede naman magdugtong po basta same po ng wire size, sold separately yung fuse tap po.

[@nikventure]

Lods pwede kahit saan bakante sa fuse box maglagay ng power supply? Diko kase alam kung saan fuse ng dome light ko.

[@carbitstv]

Actually, walang bakante na fuselocation kay Brio, i would recommend hanap ka ng hot fuse na hindi critical (ex. Horn fuse) then dun ka mag fuse tap.

[@jonasval8271]

good day sir, saan store po kayo bumili ng LED stepsil? naghahanap kase ako para sa mirage g4, yung nakikita ko lang po na LED yung sa unahang dalawang pinto lang, yung sa passenger sa likod walang LED.. thanks sir! gayahin ko yung sa inyo na method

[@carbitstv]

Usually sa online ling din po ako nabili, puna customize ko lng color nito para bumagay sa interiors. pero Shopee/Lazada po madami

[@joevalaguilera6416]

Ang hirap pala mag diy sir baka nmn po pa install ako hehehe

[@carbitstv]

hehehe mejo overwhelming at first pero alam ko kaya nyo din po yan