How to Install Front Passenger CV Axle 2003-08 Mazda 6

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@steveschreiber7743]

Probably one of the best videos I've ever seen for auto repair. Sue calls out socket sizes and torque specs like a pro that she is. Huge one stop video. Thank you very much!!

[@1AAuto]

+Steve Schreiber Thanks so much for the feedback!

[@mercedeslindigenous4219]

I would like to thank the mechanic for the great step by step video. I purchased the axle from A1 auto and just swapped it out this morning and it only took me about a hour and a half, no time wasted looking for tools because we have been told everything we need. The parts are good so far I only drove about 60 miles on the new part so anything happens Ill update but everything went flawless and I didnt have to remove the caliper but I followed all the other instructions to the T. THANK YOU

[@rrmorris67]

You can see I commented 3 years ago because this video helped me replace the passenger side CV axle on my 2005 Mazda 6, which is still in the family. Well, I came back to this video once more because I had to replace the CV axle on my 2008 Mazda 6. Yes, I have 2 Mazda 6 cars from this time frame. Actually, I also have a 2014 Mazda 6 and a 2010 Mazda 3. What can I say? I love Mazdas. This is a pretty great video. It pretty much covers it. A word of advice: Go to harbor Freight if you need to and get one of their 25" 1/2 drive breaker bars. You are gonna need it to bust that 32mm Center axle nut loose. I had to hammer pretty hard on the new cv shaft to get it to get on there past that clip ring thingy. I had to use a grinder wheel to clean up the axle afterward in order to get the new 32 mm center nut on there. hammering on the shaft at the end cause it to mush and flare out a little bit and the nut wouldnt go on clean. No big deal. Other than that it goes exactly as her video says. I had to remove the caliper, and I had to remove the fork bolt, just as she did.

[@johngowetski1582]

I really like the way you call out the bolt size & socket required with the torque spec. Great video, Thank you

[@jnicksnewstart]

Great video, Sue! Keep up the good work. I'm getting old and can't see as good as I used to. Your videos help me know what to look for rather than search around endlessly with reading glasses and a flashlight.

[@mikesmith2248]

Sue great video, I did the job in an hour on my 2008 Mazda 6. Thanks

[@jondillon6325]

This was by far the best video I've ever seen on the subject of CV axle r and r or any other auto repair. Thanks AA AUTO FOR THE TORQUE SPECIFICATIONS. Informative and well done.

[@1AAuto]

+jon dillon Thanks for checking us out!

[@hushmotor1]

I googled to know what was done today to my Mazda 6 gh, and found this video. Super educational, thanks for making this!

[@rrmorris67]

Fanastic video. Gave me the courage to order a cv assembly for my 2005 Mazda 6 that has been clunking for literally years. Gonna tear into it soon.

[@1AAuto]

+Rob Morris Thanks for checking us out! 1AAuto.com

[@bagz760]

Hey Rob, did the cv assembly swap help get rid of a high pitched whinney noise from under the car as well ?? I have the same year and make 2005 mazda 6

[@mattmiller9185]

Wow. Thanks for the video. I've never attempted anything like this before and got the job done in a couple of hours. Thanks for making this available and keep up the awesome work!

[@1AAuto]

+matt miller Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

[@DonteWilsonChrisDorner]

Man, I wish I could get my axle back in that easily.

[@RyanDavis-j5s]

You’ve taught me everything I’ve ever needed abojt a Mazda

[@CarlosMendoza-pi4vo]

I love it. You are clear and good explaining the process. Thank you

[@1AAuto]

+Carlos Mendoza Thank you for the feedback and for watching!

[@Jay-oi2jz]

This is an outstanding video. She explained everything and the size socket n the use of torquing the bolts correctly. Great work. 2 thumbs up.👍👍

[@1AAuto]

+Jay ????? Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@FarmerPierce]

I will say just one thing. The bolt that connects the lower control arm to the strut fork be prepared to replace it. I know this video is a few years old 11/6/2021 I’ve been doing both sides and both the little stops just bent over while loosing the 15mm bolt.

[@eddieriddle3623]

Nice job explaining the process. I'm wondering why i see a bunch of shiney new parts with no explanation as to why they were replaced. I. E Upper and lower control arms and wishbone.

[@Krytren]

Excellent video thank you, Really appreciate the heads up about the pressed in lower. I was definitely put myself in a bind, Thank you for saving the day.

[@RecastRelics]

But what if you can't get the axle out of the knuckle. And have to take off the whole thing? And the axle won't fit into the extension shaft because the ring doesn't fit back flush in the spline its connecting too on the car. Is there a tool to get the retention ring back on the shaft?

[@josemariasilvaneto4862]

Excellent video, now the exchange is easy. Congratulations. Brazil

[@pinktr_ee]

so you can fit a hammer up in there to knock out the inner CV case but I have exhaust all in my way. and there's a cover that's also in my way. either you didn't show a whole exhaust removal or you have the exact model with diferent exhaust setup than me cuz idk how I'm gonna manage to get that off the inner splines

[@redbeard3852]

Very nice video. Easy to follow. I'm trying to figure out what part my 08 mazda6 needs. I can only see it though. Just don't know what to call it to search for. If you guys have a video on it though. I'll probably by it from you guys even if it cost less elsewhere. The video makes it worth it

[@velkrossytc588]

Can the 2006 Mazda 6 CV Axle fit onto the 2006 Mazdaspeed 6? How much HP is too much for the mazda 6 CV axle? My boot ruptured on the passenger side and now I have to find a replacement. Mazda 6 is 140$ for a pair, Mazdaspeed 6 is 750$ for a pair, what a big difference!

[@dominicpizzi2189]

Great video! And awesome job! I just have one question I saw that the new axle doesn't have that piece in the he middle of the axle for the wishbone? Does that matter? Thank you for your help and knowledge!👍

[@nobodyschild967]

Although same "generation", are axels same for both 2005 & 2006 models? I know the front brake rotors, calipers & pads are different because the 05 front rotors are 3/4" smaller in diameter than the 06....

[@ajmartinez1514]

I love her she is really good,very Professional,Way Of Explaining is so clear,helpful Very Good I'm Always Checking with you Guys,Awesome Videos Best Ones. subscribed

[@AustinWilhite]

What did you spray the shaft with to clean it in order to slide the CV axle back in?

[@typhonrider]

Hello, Does your CV-Axles fit European models aswell? I need new front axles, but can't find any retailers for it. I have a Mazda 6 GG, Sedan - 2003 model.

[@BetoElAlacran]

Great video! I was able to switch one out earlier today thanks to the vid! Noice.. noice..

[@1AAuto]

+Beto C. Thanks for checking us out! 1AAuto.com

[@rambler295]

I’m doing this job on my 05 Mazda 6 S hatchback. When I go to put the new one on I notice the splines on the end going into the transmission don’t line up with the splines on the other side of that little retainer clip, so I can’t get the new one to go in. What do I do?

[@EdAb]

Sue you do a fabulous job on these videos!!! My 2007 Mazda 6 has a drumming/rotational noise coming from the right front. At first I thought it was coming from the outer bearing, but now I'm thinking it might be coming from the centre bearing, on the axle extension. Will you be making a video on how to RR the extension portion? Do you have any tips on how determine which bearing might be causing the noise? It does not appear that you list the extension portion for sale, are they available? Thank you very much!

[@1AAuto]

+Yuk Tuk Thank you for watching! We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. We do not currently offer the extension you are referring to for this application. 1aauto.com

[@DarthMasiah]

what was making the noise?

[@tonycervantes4816]

I looked In other videos you should never tighten with the torque wrench while the car is up, it should be when it is already on the ground. Because the arm control is damaged again. I want to know if it's true

[@tannerhackney1447]

What size pickle fork did you use?

[@68pishta68]

@13:07, how far does the CV go onto the cross shaft, until the shield hits the bearing? Mine doesnt go that far and seems to slide 1-4mm back and forth?

[@fatboy933]

You are the best Sue

[@miguelrios1019]

Same fit for a 1995 mazda protege! Good job on the videi!

[@1AAuto]

+Miguel Rios Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@dandopa1990]

is there a video in which you change the passenger axel seal? The one on the transmission

[@DGKDiligan]

Im currently doing this right now. Driverside was cake but for some reason I CAN NOT get the upper control arm to bolt back on it's like the axle is stopping me. There's a whole 3 inch gap or more and it's not budging

[@knocknboss36]

Video was great !!! Couldnt have explained it easier ! Very helpful now i want to give it a try on my mazda !

[@1AAuto]

+knockn boss Thank you for your positive feedback! We are happy we could help.

[@user-vm2ke3yk9n]

Omg I separated to 2 lower ball joints I don’t know y I’m removing the cv shaft to get to the alternator what do I need to press it back in is ther a tool from Napa that I can buy wish I seen this video earlier

[@Thethe49er]

How do I remove the extension shaft please help I’m feeling really down and stuck on this

[@appalachianadventures9727]

Thank you for this video I suspect mine is going out finding white lithium grease under the boot is that what they are typically packed with?

[@1AAuto]

+James Goodman Thanks for watching! It can depend on the manufacturer, but they will all use an acceptable CV grease to insure they work properly! 1aauto.com

[@renenunez4015]

Excelente video tanks saludes

[@MrSnoop030]

Still love your video's and they are very usefull..But ive got 2 questions. 1:Why does the old axle have some kind of rubber ring mounted in the middle? And 2: Can you guys please make a video of how to replace a parking brake cable? Didnt find much about it on the internet. Keep up the good work and many thanks from the Netherlands. 2 thumbs up!!!

[@1AAuto]

+Cherrel Hokahin Thanks for checking us out!

[@jazzman247]

Excellent Tutorial - Thank you!

[@1AAuto]

+Darren Wilson Thanks for checking us out. 1aauto.com

[@panagiotisf7228]

Do you guys have the intermediate shaft part number that the cv axle connects too?

[@jorginm]

I'm looking this procedure for mazda 3 2004. Do you have it? tks

[@1AAuto]

+Jorge Monsalve It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model. Thank you for asking. 1aauto.com

[@MPHMitch]

how do you get it off when your exhaust is in the way

[@thewoke9904]

How did you manage to do it ?

[@rushsx190]

Great video! Is the car a 2.3L or 3.0L. I noticed that there is no exhaust pipe under the CV like on my 3.0L

[@xaviier49]

Tom Roche 2.3L because the 3.0L comes with a spoiler

[@tingreferral4318]

this is definitely the 4 cyl model. Single exhaust pipe right around the 7:15 mark

[@grimchuckles9484]

Is this same procedure for 2010 mazda 6?

[@1AAuto]

+Grim Chuckles We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@stevendearing4619]

Was the axle nut not reverse threaded

[@jamesrichardson771]

Wow💥 good job girl, 🔧👍🔨

[@woyesamcomputerlimited3830]

can i swap the front shaft from left to right

[@pogo1140]

Mine is stuck in the diff. and I've been unable to pull it out no matter how much pressure I put on the prybar that I'm using.

[@angelmanuelcamacho8690]

Yeah it's easy with the car up in the air, try that job with a jack on the floor with snow melting all around you and pants and all getting wet and smelling like grease all uncomfortable and wet because of the snow and what not. And then on top of that the auto part store give you an after market part that won't go all the way in the transmission and its leaking fluid.

[@bigmike4720]

How do I know if I have the model that's has to be pressed on and off mines a 2003

[@danielguzman8346]

Is it safe to use a hammer to put back in?

[@Scott-eo7lj]

Why was no grease added to the cv axle?

[@phatt180]

scott devlin is it recommended to put some grease on the splines?

[@lilmosca4607]

Wait so its 220 ft of torque to take the part out? I have the air gun and its max is 68 ft of torque.

[@carlosbanegas7577]

thank very much

[@ncvman]

Great job thanks

[@1AAuto]

+NC Vman Thank you!

[@33ad1]

Great Video. The recording and lighting and zooming is very good. But i wish the mechanic would use some power tools to speed up the video . Using that long breaker bar to loosen the axle nut was quite dangerous b/c it was too close to the body and may scratch the paint. An air impact is better.

[@1AAuto]

+33ad1 Thanks for the feedback!

[@codylavin9718]

Is that center shaft supposed to move a lot?!?!?!

[@bigmike4720]

Will a 2003 be the same way

[@1AAuto]

This video is applicable to the 03, 04, 05, 06, 07, 08 Mazda 6. Thanks for watching! +mike levern

[@petermaxwell2076]

Thanks

[@JuanGonzalez-vn7zg]

I cant remove my axel nut with the breaker bar😑

[@vince_only_way_is_up]

Mine was not fitting due to the 2 inside grooves... should easily fit by hand.

[@josevalladares7619]

👍👍👍👍👍👍👍👍👍👍

[@1AAuto]

+Jose Valladares Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@RideOrangeKTM]

Damm shes good

[@electronpusher604]

Uses the same music as the Car Wizard.

[@peanutaxis]

14:35 BWaaahahahahaa!

[@iidropziisavage6086]

this wouldve been a good video if you didnt loosen everything first n then tell us to take the caliper off now im stuck with everything lose and no leverage to take off the caliper

[@droopyey3398]

Didn’t need to take off brake caliber

[@austinprater5979]

This does not work for 06

[@kamalabbady6778]

did she just called the axle nut a puppy, OK

[@TonyoTorres]

Ttthhhhaaaannnnkkkkk yyyoouu !

[@1AAuto]

+SR. TORRES Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@monicacostello4487]

J