How To Install Minn Kota Terrova i-Pilot Trolling Motor

Learn how to install a Minn Kota Terrova i-Pilot trolling motor on your boat with Steve and Jake from Accurate Marine Services in Naples, Florida. #minnkota #minnkotainstall
Tackle Shop → obsw.it/s/21x
Subscribe → bit.ly/AF-subscribe
▬▬▬▬ Stay Connected ▬▬▬▬
Website → bit.ly/2CHzl2i
Facebook → bit.ly/2BuOzbA
Instagram → bit.ly/2BvDM0F
Twitter → bit.ly/2BQAt79
New TV Series → bit.ly/2DM5F77
Bass Fishing Headwaters Lake - • Unleashing Epic Bass F...
Sebago Lake Maine Fishing - • 🎣 Master The Art Of Se...

[@frankdickey9470]

This is 100% A++ and done on a professional with critical "need-to-know" info to install the Terrova unit. Thanks a million guys. Well Done!! I will be doing this install next week and will have this video up on my chromebook side by side with my work area.

[@chubbrock659]

Thanks for the video, I’m preparing to add the same motor to my pontoon this week. Looks pretty straight forward.

[@leealonzo8578]

guys you have a great show

[@TeamHardLife]

Cool knowledge to know and see.. made easy..

[@appetite4thewild994]

Well done.

[@loopedrevo]

Good job. Silicone those washers on the front underside of those 2 bolts, that's where all the water will be splashing to.

[@SpecializedCharters]

Thanks for watching the video dude! Good eye! We did actually silicone the exterior bottom fastener array, which did include a nylon size matched washer and a small dab of silicone. Filming a process like this is very different and lots gets edited for time and/or gets done when camera is off. Regardless, your comment is 💯 relevant and again, good eye!

[@jaredkeil2587]

Thanks for the video, I see you recommend a deka agm battery, which group size for the terrova? Is a lithium battery worth the investment on a terrova?

[@srq911]

would have liked to see gps puck placement and install but good video. thanks

[@thetravelingcaptain]

Are you wondering about the heading sensor for the Ipilot? That was installed on centerline of boat just forward of motor. Not much to show other than 2 screws and pos/neg wire. Sensor uses wireless connection to Terrova.

[@buckrockerm]

I watched the video twice thinking I missed the gps puck install. You show it but never mention it install or it’s placement?

[@mauritobias8759]

Awesome video 🤙 WHAT POWER PLUG DID YOU USE ???

[@rodneybyars6147]

What is the shaft length on that? I'm installing a 54 or a 60"on my 17' mako pro skiff. It has 19" to the water from the mount. Do I need a 60" or the 54". Thanks Great video

[@flyjets]

You forgot about sealing the underside of the two forward bolts where the washer/nut attaches.. :-)

[@infinitesolutions2602]

Alhamdulillah. Very good.

[@johnmclaughlin7805]

How about a review on that terrova! Thinking about replacing an old Minn Kota on the boat I just bought. That Terrova come with a cordless foot pedal to??

[@addictivefishing]

It's the only trolling motor I have ever owned. THE BEST.

[@alfakilla1]

So, when did the power plug get installed??? Factory?? Reason I ask is that I do not have a power plug on my boat...would have been nice to see installing to battery n plug install

[@striper8311]

Hi , great video, I have a new ulterra that I’m having issues with and have no faith in it, I’m waiting on getting a new terrova, the ulterra is a 36 112 60” on a quick release, can I just put a terrova 36” 112 60” on that same quick release and be done with it? Thanks in advance

[@thetravelingcaptain]

As long as you used the RTA-54 quick release mount then yes. If not, please purchase the RTA-54 with your new motor.

[@I_am_archie]

If I mount my new terrova on the starboard side can I turn the head and motor 180° to secure it after deploy? Intent is as you mentioned, keeping the head inside the boat.

[@thetravelingcaptain]

The head and shaft turn 360 degrees once released from base to stow so, yes. Choose which ever direction protrudes the least.

[@mikem1904]

Nice. I’m installing a trolling motor on my Hewe’s this month. Where can I get in contact with you guys to help me with that? I’m in Florida

[@addictivefishing]

Accurate Marine Services in Naples, Florida

[@jacoblesniewski2263]

Accurate Marine Services [phone]

[@johntrask8775]

How do you mount if no access below the unit?

[@carphuntingod]

when reviewing several of these videos on installing terrovas... i've run into a bunch that say the shaft collar (or the inside edge of the semi-circular notch in the aluminum base of the motor should be at least 1.5" from the gunwale of the boat. After installing... that looks like excessive protection of the motor shaft. 1.5" from the shaft looks like it should be enough clearance. When you mount these... what is your clearance to the shaft the the mount collar?

[@thetravelingcaptain]

They always try to adhere to the manufacturers recommendations. The manufacturer is looking to avoid any contact with the rub rail or hull and motor shaft which is why that distance is provided. A lot of times it comes down to the design of your boat and how your fasteners will be placed through the deck. This particular install followed Minn Kota's recommendation exactly as fastener location was not an issue.

[@bobhoffman1869]

@@thetravelingcaptain I loved this video and tried to follow it exactly and had issues with the plate too close to the edge. I disagree with you and the video in that Minnkota actually states with the shaft down there should be a minimum of 1 1/2 inches from the gunnel to the SHAFT when deployed!. If you use a plumb bob to have the inch and half clearance from the aluminum resting place, you will have 2 1/4 inches clearance to the shaft. This is due to the 3/4 inch collar on the shaft. This should be clarified as that 3/4 inch makes a huge difference in mounting

[@thetravelingcaptain]

@@bobhoffman1869, as mentioned multiple times in comments, your install may differ from the one in this video. Unless you own a Beavertail skiff, the shape of your vessel's bow may not be like the one in this video. The installers followed Minn Kota's guidelines and completed a successful install. This vessel is still running around with the same troller on the bow and no damage from it. So, allow me to state this again, your install may differ from the one in this video. Please read all of the directions provided by the manufacturer before attempting to start your project.

[@mactownsend2890]

Is there a special tool that you use to cut the excess off cable ties to prevent those sharp, jagged edges? Thanks

[@thetravelingcaptain]

Yes there is a tool to trim cable ties off. It is available at West Marine or on Amazon. You can also buy self trimming cable ties which do to require a cutting tool. Those are also available from same vendors.

[@willhowell9972]

A pair of wire cutters that cut flush work well

[@windyknot2094]

What about the iPilot link location & installation??

[@garrydye2394]

Agreed. Where is the rest of the install?

[@weixiao9470]

Where is sensor installation part?

[@jamspeed001]

How big is that boat

[@bigginsg8711]

Wish they would have showed the running of the link cable

[@thetravelingcaptain]

Which part of the running would you like to have seen? It is zip tied under starboard side gunnel in an area manufacturer ran other cables to rear of skiff. Minn Kota provides a long enough cable to get it around your boat to console. Trolling motor has a shorter length cable that then attaches to extension which is connected to Solix 10.

[@chandlerhill6453]

Wish they showed how to get the back to bolts

[@thetravelingcaptain]

@@chandlerhill6453 Long arms through a small access area inside forward hatch. Every vessel installation is different so there is honestly no need to show exactly how it is done. Unless you own a Beavertail Vengeance, will not be the same.

[@jasonklein4031]

Wow. Lot of shitty comments on here. Thought the clip was pretty helpful. Thanks

[@tommyliu4683]

Any reason your selected the terrova and not the ulterra?

[@addictivefishing]

I use the Ulterra on my bay boats and the Terrova on my skiffs.

[@1tr1ck]

Overcast day no need for sunnys 🤣

[@adantorres2370]

what about the mini Kota gps puck?

[@thetravelingcaptain]

Heading sensor? 2 screws and pos/neg wires installed on centerline just forward of outboard. Not complicated to install so did not show it.

[@mikebromelow8514]

@@thetravelingcaptain Not complicated but still important information for folks like myself watching all these installation videos! ;)

[@thetravelingcaptain]

@@mikebromelow8514 Your point is valid, but don't worry that part of the job is very simple. Minn Kota provides detailed instructions on how/where they recommend you install sensor. All vessels are different and your mounting location will most likely differ from this one. It is highly recommended you read all of the included installation instructions before proceeding with your own. Thanks for watching this video.

[@honkey_boy]

What batteries?

[@thetravelingcaptain]

Deka AGM batteries, they came with boat from manufacturer. If purchasing for your own use, choose a good quality AGM battery brand with nation wide warranty.

[@bsummit826]

You guys didn't have to mount the gps puck?

[@thetravelingcaptain]

That "GPS puck" you are speaking of is not a GPS. It is actually a digital compass known as a heading sensor. The heading sensor does not receive any GPS signal. What it actually does is tell the motor board where the back of the boat is pointed so your spot lock becomes hyper accurate and allows the motor to better compensate for wind and current.

[@bsummit826]

@@thetravelingcaptain Ok cool. You guys didn't have to mount the digital compass known as a heading sensor?

[@thetravelingcaptain]

@@bsummit826 I did not, but the installers at Accurate Marine sure did. Sometimes videos get compressed for time to fit KZbin, shots get left out. Minn Kota does a great job of providing detailed instructions for that sensor. Also, the location for mounting changes with every boat, so its best to find the spot on your particular vessel to install. Its very simple, 2 screws, 1 hole to pass wire through and a positive and negative wire.

[@kyungkim805.]

You didn’t show how to run the battery’s and power

[@thetravelingcaptain]

This video was about installing a physical electric motor on the vessel. Battery wiring instructions are provided in box for you by MinnKota. Read all included instructions and please take care when connecting power. Batteries connected in 24Vdc create enough current to do extreme damage.

[@agentguerry]

why not pencil mark the outside of the troll housing, then lift it all up and place it back on the pencil marks, then mark your holes ....

[@thetravelingcaptain]

You have your way of marking your work and Accurate Marine has their way. Both will arrive at the same destination. Please feel free to install hundreds of trolling motors your way just as the guys in this video do it their way.

[@raptor660cc1]

You're gonna blowout the backside of the fiberglass pushing that hard.

[@thetravelingcaptain]

Which specific fiberglass are you referring to in this video? Could you elaborate how said fiberglass will blow out?

[@Slazmoservicing4209]

Pushing the drill as hard as he can, would've been better to pilot hole and drill from both sides.

[@GmanfromTexas]

good job but too many commercials

[@BruteManny]

Didn’t show how he tight the bolt under the deck lmao that thump down sorry bro

[@eastcoastoutdoors902]

jake ramirez ur that type of person?? So how does it feel to be the only dipshit to dislike this video?😂

[@addictivefishing]

It was too dark in the hatch to see anything.

[@BruteManny]

Addictive Fishing lol you could use flash light 💡

[@thetravelingcaptain]

@@BruteManny Unfortunately, there was not enough room to fit anything but an arm and tool through the access point to reach bolts. The installer put his whole body in hatch then reached through that access point to put nuts on the bolts. I understand how important this is and will take your request in to consideration for future installs and make sure to show you how to put a nut on a bolt.

[@liamwindsor5854]

Old mate hair do is crap, just go bald old mate!

[@SpecializedCharters]

Thanks for watching the video. I’ll get with my hairdresser and see if there is anything I can do to hide the scars on my scalp and then maybe I can meet with your approval. I’ll follow up with you after I get it all done.

[@jamesscott4026]

Your hair is fine and the video was well done. Liam is just so proud of his mullet he cant help but criticize .

[@dougcole7677]

Silicone is NOT the correct sealant here, in fact other than working around wind sheild glass, silicone has no place on a boat, not even "marine" silicone. 3M 4200 (not 5200) would be a much better choice, or maybe life caulk. The best way to do it would be to overdrill the holes a little then pot them with thickened epoxy, then redrill them and seal with 4200. They will probably be OK here on the Beavertail since it is no wood construction, but it's a disaster to this on a boat with a wood core. You are asking for core rot in a few years to do it this way. I'm surprised that pros don't know this.

[@thetravelingcaptain]

In your professional opinion why is 3M 4200 a better choice? Have you consulted a representative for 3M who advised you on proper sealant for this particular job? 3M Marine silicone is a valid choice for this install where it is above the waterline through closed cell foam core and fiberglass substrate. Adhesive properties of 4200 are not needed for this type of work. As far as your comment on "drill and fill" technique, this is not the type of job that would require you to do it. The puck part of the quick release bracket an large fender washers below provide enough strength. Just make sure to use the correct Minn Kota quick release bracket for the 80lb thrust and below motors or HD version for 112lb thrust motor.