How to Install Replace Auxito LED Headlights: 07-11 Honda CRV - Installation Instructions and Review

[@itsroads206]

Just installed these bad boys! Love the fact that you can take off the ring and install then pin down with no headaches! Especially the driver’s side! 10/10 would recommend! 😎🤙🏽

[@justinhardin7318]

The rubber seal is called a “baffle” and it’s almost easier to remove the battery for easier access on the drivers side. I have an 07 crv and you answered all my questions. Good vid

[@twald1]

Video was VERY useful in replacing halogen bulbs w LED on a 09 CRV. His gold nugget is to take the ring off the lights (at 2:15), install that, and then insert the bulbs in to that. The other thing is like he is saying, passenger side will take about 5 mins, driver side has minimal room but can be done. I LOOSENED two bolts that were right there pretty obvious that were playing a roll in securing the fuse box, came in from the bottom inside w the bulb, gave a bit of a lift to the fuse box as it was loosened, and that was enough to get the bulb by. There is also a comment by @bumblebvr6 mentioning the ability to lift the fuse box from some clips that are holding it, that would be golden if you can get that done, I'm sure it can, it looks as though it can, I tried that but didn't feel like it was going to work before I broke something. Would definitely be easier if you got that to work, other wise, loosen those two bolts you'll see right there and lift a bit on the fuse box.

[@bumblebvr6]

I just did this installation with another brand LED kit that did not feature the removable bulb base. One thing to mention, the fuse box on the driver’s side can be un clipped from the bracket it rests on, giving you plenty of room to work. You can bend the front metal bracket as well and bend back into place when finished. I have to trim away some of the center sections of the rubber covers to fit over the fans in the end of my bulbs. Was pretty tricky to install them with the covers on and getting the retaking clips to hold the bulb. Got it done though.

[@glendahopp]

I installed these on the passenger side no problem but how do I un-clip the fuse box?

[@bumblebvr6]

@@glendahopp From what I remember, it just pulls up. The wires will be a bit tight to work around, but it helps. There is a tab you have to push while pulling up on the fuse box from what I remember?

[@wilhelm4236]

Great tip! You should polish the headlight for a new car look. Very easy to do.

[@johnlozauskas778]

This was an excellent video. One thing that would help alot is being shown how to get these right side up. I installed these, but they were upside down. I could not get them in upside down, so I just drive with them in High Beam mode and the have them light up the road and 1/2 of the sky in regular mode.

[@wheelrolling78]

It might be switch to the other side of the car

[@johnnyappleseed8742]

What is the sequence? Three prongs out. Clip three prongs. Stick bulb in rubber gasket. Twist bulb along with the rubber gasket into three prongs. Is that the right sequence? I have a CRV 2004.

[@DescentBeliever]

Need a bit more clarification on how we adjusted the LEDs

[@patrickwhitaker6362]

Tried installing these today and both rings dropped in the engine bay 😒 Waiting till dark so I can find them.

[@Cryptony1975]

do these work with day time running lights??

[@MarkBerry-fx7zp]

I disconnect my daytime light from fuse box got annoying to see plus saves headlight use

[@Cryptony1975]

@@MarkBerry-fx7zp which box and what # fuse. I have 2008 crv

[@MarkBerry-fx7zp]

@@Cryptony1975 fuse box on inside of car look at owners manual

[@thndr_5468]

those rubber seals are impossible to work with

[@johnlozauskas778]

My 15 year old daughter figured that one out. I put the LEDS through the rubber gasket, then installed them. EZ-PZ.

[@thndr_5468]

@@johnlozauskas778 yeah I figured it out pretty quickly. Got frustrated.

[@customization2k272]

I’m starting to question if you actually installed it on the drivers side

[@wesleymiller4856]

I love them really good thank you there want I want and needed perfect at night

[@masterofuploader4]

Why is your crv not equiped with Projector lamp?

[@joevillegas8754]

They come equipped with projector lights?

[@masterofuploader4]

@@joevillegas8754 yep our CRV 2009 is equipped with it

[@jgizzy]

In North America, the 07-11 CR-Vs never came here with projector headlamps, they were all reflective lense types. Your country got the better versions we did not get.

[@masterofuploader4]

@@jgizzy well at least you are in america. You live in a better country than ours

[@jgizzy]

@@masterofuploader4 I feel like America is not as great as we like to claim. But then again I've never lived in your country so I really cannot compare truly. Only other country outside of Canada and Mexico I've been to is Spain (Barcelona) and I felt like that was a much better place to live for overall happiness in daily living.

[@gillenmara1811]

Why the heck would he show installation on the driver side where we can’t see anything he’s doing 🤦🏻‍♂️ ??? Wouldn’t it make sense to install on the open side to show us then walk us through the cramped side. This is so backwards 🤦🏻‍♂️

[@MrViper7121]

Installing these with those push springs are a pain in the ass and the rubber grommet doesn't help at all. Those video is completely useless as an install video

[@bumblebvr6]

Make a better video then. The guy tried to help out. It’s a good video IMO. Just read my comments on how to help make the installation easier.

[@MrViper7121]

@@bumblebvr6 ok then you help me