The shield is detachable from the bulb so you can install the shield plate first then clip on the assembly,then dust cover so no water gets in. Last is the bulb ! The dust cover will not prevent the fan to get proper air circulation ! Hope that helped anyone !
@abdalladavis5 жыл бұрын
You can Twist Off the Shiny Silver, Three-Pronged peice from the HeadLamp, then fit it into the HeadLight Housing, then put the Clip back on, then the Rubber Gasket, then Insert the Lamp/Bulb into the Housing and Plug it in. Also, you can Rotate the Lamp/Bulb while it is In the HeadLight Housing to Adjust the Direction of the Light. Just some friendly tips. Hope they help.
@n05tr4d4177u55 жыл бұрын
A. Davis yes, this is the way to go, by the way, did you experience any issues with the gasket melting overtime?
@trido38154 жыл бұрын
I did the exact same thing on my '08 CRV. It took me about 5 minutes on each side. I struggled a little bit on the driver side since I did not have a lot room and the led bulb was big and long. Anyways, it is so far so good. The rubber gaskets have not melted yet.
@abdalladavis4 жыл бұрын
@Jimmy Gomez, no I did not. Thankfully no melted gaskets.
@johnnyappleseed87424 жыл бұрын
Are you talking about the rubber gasket that he said he couldn't used? Would that depend on the size of the LED butt? I am worry about the rubber gasket melting too. How much driving do you do in term of single non-stop trip?
@trido38154 жыл бұрын
@@johnnyappleseed8742 it has been a few weeks since I installed the LED bulbs with the rubber gaskets on. It is fine. It is not a good idea not to have the gaskets. The water will get in the light fixtures. There will be moisture condensation.
@kamelstar22167 жыл бұрын
Watch all the moisture in the housing on a rainy day,speaking from experience,not hating
@bmwmsport116 жыл бұрын
You need to install the rubber dust cover to keep moisture out. If it ever rains you’ll notice major condensation build up inside of the housing. I’ve dealt with a lot of HID setups before and the rubber covers are always a pain to work around but much needed. Will need to modify them to seal against the bulb. There’s a reason cars without the rubber dust cover use bulbs that have gaskets
@CerealKiller187 Жыл бұрын
No no no. He's a KZbin personality he knows best 😂
@wbfarlow5 жыл бұрын
Great video. I just did this to my 2009 CRV. I cut out the center of the rubber grommets and they are fine. Getting the grommet in place on the driver's side was difficult, but doable. I rotated the silver bezel so I could put the wire side down. I don't know why you'd want it facing up.
@AwkwardHamster5 жыл бұрын
Thanks
@vizualmrs7 жыл бұрын
Clean and clarity through out the video. Didn't cut anything out. I love it. You saved my life at night and saved time. A huge thank you.
@AwkwardHamster7 жыл бұрын
+fed Z Thanks
@Stelcom662 жыл бұрын
Thanks for this. I watched this after replacing my 2012's driver side bulb. Took a while to get the clip in, your detailed view is what I wanted to see for future reference. I took a snapshot of the part the clip hooks onto since I couldn't really see it on mine.
@AwkwardHamster2 жыл бұрын
You’re very welcome
@jeffpotter89845 ай бұрын
thanks man! I was wondering if it was difficult to switch to LED. Appreciate your time!
@AwkwardHamster5 ай бұрын
Thanks
@samrosenberg5433 жыл бұрын
This was so helpful! Convinced me I could do this on my 2011 CR-V and it was even easier than I expected. Thank you!
@AwkwardHamster3 жыл бұрын
cool
@carljames80788 жыл бұрын
Awesome video, thanks AH. The bulbs design looks so cool, love it. Does it make fan noise?
@AwkwardHamster8 жыл бұрын
yes, there is a low humming noise coming from the fan
@VetteTJB017 жыл бұрын
Excellent video...thank you very much for posting! I am installing these in my Nephew's car this weekend. Did the wife's last night & took me about 10 minutes. So far I am very impressed with this product. Thanks again!
@AwkwardHamster7 жыл бұрын
+Tery Biglin Excellent
@VetteTJB017 жыл бұрын
Hey Mr. Hamster one quick question for you and that's the bulb placement. Should the bulbs be installed with the wire up? As far as the actual LED's are concerned, should they be pointing up/down or side/side?
@tomhilmer95544 ай бұрын
I thought you trust the l.e.d. Bulb to disattach the ballast so you can put the boot on?
@iand51884 жыл бұрын
First, modify the seal instead of losing it. Second, use dialectic grease on the plugs/ connections
@travispoteat5 жыл бұрын
That bulb will fit with the rubber gasket just place the bulb through and pull the gasket inside out to get the clip installed properly then just pull gasket back in place just put a set of h4 on my Tacoma and it worked great. If this isn’t done you’ll have moisture all in your headlight not to mention electrical and water don’t mix well.
@gibbonzo125Ай бұрын
GREAT visuals man, thank you for sharing.
@AwkwardHamsterАй бұрын
My pleasure
@terrylia42352 жыл бұрын
Wire from the bulb has to be facing downwards. Reading the instructions helps.
@ceckoslav7 жыл бұрын
OK, you installed the bulb, but that was the easy part of the installation. What about the rubber gaskets? I assume you don't drive without them?
@AwkwardHamster7 жыл бұрын
+Boyan Aleksandrov I kept them off. Don't need them.
@qwerty.us4125 жыл бұрын
@@AwkwardHamster have your headlights ruined yet? You know moisture and all..
@motherknowsbest93265 жыл бұрын
ImAbraham headlights are still fine. The fog light on the other hand is on its last leg. The driver’s side doesn’t come on half the time.
@mrkdavek5 жыл бұрын
I'm thinking upgrading my headlights the same as you. Have you had any problems with them? Also those led headlights, Do they have daytime running lights, normal and high beams in those leds?
@AwkwardHamster5 жыл бұрын
I haven’t had a problem. In the daytime, the lights are roughly half brightness compared to nighttime. High beam still works.
@imds1237 жыл бұрын
As a CRV owner I am looking at the OPT 7 flux beam led bulbs. Either way this is a great comparison against the stock Halogen. Do your DRL's still work with the LED bulbs? Thanks
@AwkwardHamster7 жыл бұрын
+imds123 DRL still works fine. Doesn't flicker.
@Falcon0122877 жыл бұрын
That was a GREAT video! Well done, very straight forward and well spoken! Thank you.
@AwkwardHamster7 жыл бұрын
+Nelson Olivo Thanks
@JR-kr1lv5 жыл бұрын
Thanks for showing them at night and how much difference their is, I just nought a 2010 and low beams are DULL, kick on high beams and they look like LEDs but just one bulb, don't make sense but they came like that, so I'm looking to replace them since their dull, just can't use DRL wit most of them, that's sad and they should make them for DAYTIME RUNNING LIGHTS, their on for a reason, for people to see you all the time now. They charge enough on them so make them cool to run them on DRL and last many hours like dome day, 50,000 hours some at 30,000 hours. Either way thanks for great display.
@ericheel16 жыл бұрын
ok pulled my DRL fuse and that solved the problem, which turned out good cause i wanted to eliminate the DRL'S anyway
@HockeySavants6 жыл бұрын
I installed LEDs similar to these in my 2001 CR-V...brand new headlights as well. I do have moisture buildup in one of the headlamps, so I am not sure if it's the headlamp itself or just because there's a decent amount of opening in the rear of where the rubber piece would have gone.
@jasomkovac91156 жыл бұрын
Octavio Guzman how do the bulbs you got work,(brand?), and sometimes ya gotta much about to get the rubber to seal. Though if they're after market they might not be sealed properly. Have run into that problem.
@spanky5226 жыл бұрын
What I don't like it the fact that the mounting ring is not removable from the bulb socket. On other models I have (in my motorcycles, which use the same bulb) so I am not able to mount the rubber seal back behind the bulbs. I got moisture inside the headlight after going thru the car wash. I evaporated from the heat of the bulb, but I still have to make some kind of water tight seal behind the bulb, in front of the fan so it can still keep the bulb cool.
@wrathcc7 жыл бұрын
That was my next question did u have to disable daytime running lights fuse or are they running without flicker? Thx
@AwkwardHamster7 жыл бұрын
+wrathcc Daytime running lights uses the same bulb. No change needed for my car. No issues, no flickering. If you have a European car, you may need to spend $12 for a relay harness if your lights flicker.
@wrathcc7 жыл бұрын
Any water in your headlight , especially that rubber boots are not installed ? Plz advise
@AwkwardHamster7 жыл бұрын
no water, no issues, daytime running still still work great, I still use these lights today
@trput38247 жыл бұрын
The rubber boot SHOULD be refitted. Over time, moisture and dust entering the headlight will coat the reflector surface and lens greatly reducing light efficiency. The rubber boot will not cause the bulb to over-heat. The correct installation procedure involves sliding the 3-pronged mounting plate off the LED lamp and securing it in position on the headlight with the spring clip - easier as you then don't have to work it around the ballast / heat sink / fan. Then, refit the rubber boot. Then, insert the LED assembly and plug it in.
@VetteTJB017 жыл бұрын
trput Any advise on how to remove them? In the process now of trying to install & they are being quite the bigger to remove
@trput38247 жыл бұрын
Remove the mounting plate from the LED bulb? Most better bulbs have a rotating mounting plate so that after installation, the bulb can be rotated through 90* or more to assist in setting the the correct cut off line to reduce glare to on-coming traffic. The plate may only slide off the lamp when in a certain position in the rotation. Check that it isn't secured with a small screw and close observation will probably give a clue as to the "slide off" position.
@VetteTJB017 жыл бұрын
Got it...thank you! Yes that was a bit of a bugger but def need that rubber boot. We installed but it looks like we missed a few steps so we are going to try again later today. Thank You for your post and your reply!!
@avefenixml3 жыл бұрын
What can I use on my, because I have a DRL dashboard light blinking when running but when I turn the switch to on position the dashboard light will turn off!
@provilichyvual8 жыл бұрын
I have the exact same bulbs and because they're dual sided it shines right on the high beam segment of the headlight whilst on low beam... any idea on how to stop that?
@AwkwardHamster8 жыл бұрын
+Aaron Hi. Does it happen with both LED bulbs? If you put the old halogen bulb back does high beam low beam work fine? If old bulb works fine, then I believe you the new bulb is bad and it should be replaced. But if even putting the old bulb back doesn't work fine, then it could be a problem with the relay.
@provilichyvual8 жыл бұрын
yeah, the old halogen bulb works perfectly. only shines high on high beam, the curved covers look like they aren't really doing anything. I've been stopped by police as it looks like high beam is on and they are too dazzling. Ive realligned them, but even with the focused beam positioned as low as fog lights, still shining too high... Ill contact the seller and see what they have to say.
@AwkwardHamster8 жыл бұрын
What's the brand and model of the bulb you got?
@TheTonyburris7 жыл бұрын
some kits you can twist the bulb the beam pattern sucks for these so they make the adjustable. remember they have the 180 deg limitation and its not even that much to be honest.
@DrWenChannel6 жыл бұрын
Thanks for this video. For 2011 CRV, is the process exactly the same?
@AwkwardHamster6 жыл бұрын
I would think so.
@spanky5226 жыл бұрын
Amazon sells an after market rubber boot that fits over the heat sink fan, so you're able to keep the bulb sealed and still have the cooling fan doing its job. The boots are only $9.99.
@ugcamige6 жыл бұрын
Painter D what's the name of it?
@spanky5226 жыл бұрын
They are from Tomall. Retractable rubber boots for LED headlight bulbs. I got them off Amazon.
@tamir59407 жыл бұрын
i have a 2010 honda crv and it has day time running lights. I assume yours has that too right? if so, did you have any bulb flicker or anything?
@AwkwardHamster7 жыл бұрын
no flickering seen by the human eye. My camera records at 60fps and can catch it flicker
@mcbarker115 жыл бұрын
Excellent review! And appreciate the extra info at the end. Subbed!
@AwkwardHamster5 жыл бұрын
Thanks
@schlossb Жыл бұрын
If anyone can remember their install, I feel like I can't get the bulb securely in. I put the metal ring in first, put my bulb through the rubber gasket as far as I could, then put the bulb into the headlamp. Since I needed to twist the metal ring to take it off the bulb, I assume I need to twist to secure it back on, but the rubber gasket seems to make it really hard to do that. Or I just can't get enough leverage to push in and twist. I'm worried that as soon as I start driving and go over a bump, the lights will dislodge a bit and shine every which way. Thoughts>
@Fze56567 жыл бұрын
No seal is a deal breaker. Bugs moisture and dust inside the headlights is a pain to remedy
@RichardsWorld6 жыл бұрын
I tried to make a video of fixing my car and it's 'not easy' LOL Great job!
@AwkwardHamster6 жыл бұрын
Thanks.
@larryholou Жыл бұрын
The best installation video on KZbin. Thanks.
@AwkwardHamster Жыл бұрын
Thank you
@andrewoliver96868 жыл бұрын
I think I need to get another brand of LED bulbs. I have the 360° bulbs from Stark on Amazon. It features a triangle shape which I thought was going to be a good thing. Output is only great at 5 ft. After that..it's nothing but eye strain lol
@ZDriver19964 жыл бұрын
You need to slide off the backing plate off the LED and then slide the OEM rubber seal onto the LED. Do not cut a hole in the rubber seal and do not use the LED's without a rubber seal. Your headlight assembly will oxidize. if the LED design does not allow for the backing plate to slide off then order an LED that comes with a rubber seal or and LED that fits the OEM.
@Lethal.G372 жыл бұрын
For real… I can’t believe he actually said not to use the rubber seal
@lalsitara3 жыл бұрын
Thanks for this video. It helped me to install headlight.
@AwkwardHamster3 жыл бұрын
Cool
@RockwearbyEddie2 жыл бұрын
The rubber dust and moisture boot goes on right before you install the LED bulb. You're gonna have problems if you don't put the rubber dust and moisture boot back on.
@InsomniacReviews5 жыл бұрын
When I installed these on my 2014 CRV. The lights were on all the time, even if i switched to OFF. Also lost the ability for the sensor on the dash that automatically turns the lights on and off based on outside light. aka the AUTO function. Did you experience the same issues?
@AwkwardHamster5 жыл бұрын
I have not experienced the issue you described. You can try putting the old bulb back to see if the behavior is the same. If it is, your what you said about dash light sensor would be the next focus.
@InsomniacReviews5 жыл бұрын
@@AwkwardHamster Thanks for the reply. I installed the original bulbs back in all works normal. Weird leds wouldnt turn off always on. If you leave your lights to auto, do the leds come on when dark?
@AwkwardHamster5 жыл бұрын
Now that I think about it, it could be the Day time running lights. My light is on but since it is daytime I can’t tell if it is on at the same intensity as night time.
@hardi48587 жыл бұрын
hi sir, when you install the LED to Honda car, did you use the CANBUS decoder? i recently just purchase 1 set without the CANBUS decoder to my Honda Mobilio, but after less than a minute the bulb will shut off itself. Dunno if the bulb is malfunction or need the CANBUS decoder to solve my problem.
@AwkwardHamster7 жыл бұрын
+Hardi My car did not need a CANBUS. I read it's mostly European cars that may need it. I haven't heard of Mobilio.
@Winning1175 жыл бұрын
Worked on my 1998 Honda CRV, thanks!
@AwkwardHamster5 жыл бұрын
You’re welcome
@travisdavis75075 жыл бұрын
The cover that goes over the bulb the rubber pice u dont put that back on ?
@AwkwardHamster5 жыл бұрын
I don’t put it back. After all this time no debris has gotten in there.
@IMMU167 жыл бұрын
Hi does it require extra harness to fit this led bulbs? if not will this effect on batterie and other electrical components?
@AwkwardHamster7 жыл бұрын
If I were to replace the bulbs on a European vehicle, I may need to install a harness. It doesn't affect battery or car electronics.
@IMMU167 жыл бұрын
AwkwardHamster what harness do I need for this bulbs and I live in Ireland
@ToXiC817 жыл бұрын
immu ahmed relay harness if you own a certain vehicle. They're usually needed for German cars, otherwise you will get an error code on your dashboard
@IMMU167 жыл бұрын
ToXiC81 thank you very much
@markweidenfeller34287 жыл бұрын
Is it good to leave the boot off for proper headlight bulb venting?
@AwkwardHamster7 жыл бұрын
I removed that rubber seal for proper heating
@muhammadfikry80087 жыл бұрын
Actually u can put back that rubber gsket but u must cut little bit coz the led fan is too big😊
@DG-8882 жыл бұрын
Cut a bigger circle down the middle of seal?
@TheBanindhitap7 жыл бұрын
You don't install the shield? Are you not worried water from rain or dust coming into inside the headlight?
@AwkwardHamster7 жыл бұрын
+bramantya anindhita Not worried about it. Been driving with it off for some time now and havent see any buildup
@bryanmchugh13077 жыл бұрын
I know this is an older video but I have the same vehicle and want to change over to LED from the stock halogens. My question is can these LED replacements be had at a lower kelvin rating? The one you replaced looks 5500-6000k-ish. I want the efficiency of LED but also want the K rating to be more natural say 4500k-ish.
@AwkwardHamster7 жыл бұрын
Hello. Yes, I've seen various types including those that are around 4000K. But, I don't think those are as popular considering that's the same K as halogen headlight bulbs and the halogen bulbs cost about $20 a pair (fraction of the LED bulbs). The 5500-6000K LED bulbs are more popular because it gives a xenon headlight look without having to install a conversion kit.
@bryanmchugh13077 жыл бұрын
thanks for the reply OP! I am also a flashlight collector and am more than familiar with the LED chips they use. It would be a benefit to your subscribers as to which LED chips the LED unit is using such as Cree XHP35, XHP50,XHP70. Not to familiar with the offerings from Phillips as Cree has dominated the high output flashlight market for years now. Luxeon is still around they make some good chips but as far as I know there are no Luxeons that are that high output. As for the lower K being lower output vs cool white the difference in output between them when it comes to flashlights is roughly 7% give or take. I love the fanless upgrades and truly hope I can find some LED upgrade units with Cree chips that are fanless and fit my 2004 CRV. I prefer lower k tints but if that is not available I will go with the white.
@bryanmchugh13077 жыл бұрын
I currently have Sylvania Xtreme Vision bulbs in the CRV which made a surprisingly good difference. Oh well was just hoping mothers (she is 80)CRV had supplies out there to make her low beams a good bit brighter. Now I am stuck with a money pit 1996 Mercedes e320 that has the dullest most UV damaged headlights I have ever seen. I put good fresh correct bulbs throughout the entire car which really helped in the rear but even with my brights on my standard new bulbs look like low powered yellow fog lights. They are so dim now I am to afraid to drive it at night....
@AwkwardHamster7 жыл бұрын
are the headlight glass clean? Pepboys sells the glass cleaners. Those helped with my 2000 lexus.
@bryanmchugh13077 жыл бұрын
the right side headlight housing is new and very clean, nice almost with a jewel like shine to it. The passenger side headlight housing has corroded(?)and shows UV damage it has yellowed and just started to show small cracking in whatever Honda coats their headlights housings in. I have tried the UV damaged and worn cleaning and polishing methods on my 1996 Mercedes e320 the housings on that are horrendous. They were crystal clear for like 3 days. After having done more research I have decided on Xenon HID systems for both vehicles at 6000k. There are so darn many to choose from I am pretty lost. I thought the Sylvania Xtreme Vision halogens I put in her CRV were impressive they look like run of the mill halogens compared to my friends late 90's Honda with an 8000k Xenon HID system. He got them off ebay and they are no name HID's that cost him less than $45 altogether. 8000k is to blue for me and ma but now at least I know it can be done cheap and is actually pretty easy to install. Somehow my friends no name HID system has run perfectly for a year and a half lol
@pandamik223 жыл бұрын
Will these headlights work with a 2004 crv?
@MZBallistic5 жыл бұрын
I just installed these today and my low beams are aiming up high beams down on the road. My wire is facing up like yours, what did i do wrong?
@AwkwardHamster5 жыл бұрын
Try turning the bulb, the socket metal portion on some models are adjustable and not in a fixed position. Makes installation easier.
@lelandsullivan46934 жыл бұрын
sorry but that is not a 2012 crv as you stated, has to be at least 2013 from headlight design. so is this really your car that you dont know the model or a sales promo for installing these brand of LED?
@AwkwardHamster4 жыл бұрын
Unlikely
@viktorgoreta12016 жыл бұрын
how on the honda cr-v 2000 year change the magleness and the position light?
@VetteTJB017 жыл бұрын
Does anyone know if the bulbs should be installed with the wire up OR, where the actual LED's are concerned, should they be pointing up/down or side/side? Thanks!
@AwkwardHamster7 жыл бұрын
+Tery Biglin Hi. The model I showed here doesn't allow me to rotate the butt. Other models I showed in other review videos allowed the adjusting of the but, thus adjusting the wire. The idea is to adjust the beam to how you need it. Wide, focused, etc. I would recommend shining it at a wall or garage door at night and adjust it so you see the cut off and beam is where you want it.
@VetteTJB017 жыл бұрын
Got it...thanks!!
@7692708656 жыл бұрын
The led bulb does fit but I can't put the rubber seal back on becouse the bulky component on the back of the led bulb!
@ianbreyes8 жыл бұрын
Awesome.. did you disable the DRL?
@AwkwardHamster8 жыл бұрын
+christian reyes No. I rather like keeping those operational.
@ianbreyes8 жыл бұрын
AwkwardHamster does it flicker at all? Cause i've seen cases that it flickers when DRL is turned on.
@AwkwardHamster8 жыл бұрын
+christian reyes Mine hasn't flickered.
@ianbreyes7 жыл бұрын
sorry late to ask. but how does it look in daylight? does it also serve its function as DRL?
@mohamedlarbi90447 жыл бұрын
+christian reyes hi, i have Honda Crv 2012, and my DRL works when i turn on my car. Did you tried these bulbs? Do they work with DRL without flickering? Thanks
@leov70198 жыл бұрын
Great video, thanks for your all effort.
@AwkwardHamster8 жыл бұрын
thank you
@flyfisherman41846 жыл бұрын
Since you can't reinstall the rubber weather seal with the new bulb, the inside of the headlamp assembly is wide open to water and debris. This is not a good solution.
@DragNetJoe4 жыл бұрын
Other videos of other LED kits you can separate the heatsink/ballast assembly from the front bulb, then install the rubber seal, then re-attach the back half.
@Wakko0o6 жыл бұрын
I would cut out the rubber seal so it can fit that bulb, don’t just throw it out. You can always get these rubber seals at your local auto shop if you another pair
@ltigre20315 жыл бұрын
can you do same bulb on prius video , i cant figure it out.
@manchvegasuruguayguy6 жыл бұрын
Do you don’t live somewhere that it rains or snow a lot ?? Beecause without this rubber boots installed back on your headlight housings they are going to get full of condensation and water. That’s the whole reason to have those rubber boots on all headlights..
@AwkwardHamster6 жыл бұрын
I live in New Jersey. It rains and snows a lot here. No issues so far after all these years. Also, no dust or grime in the headlight cavity.
@thomasalbertdaclan37315 жыл бұрын
How about the rubber seal..?? We cant use that already???
@AwkwardHamster5 жыл бұрын
I kept the seal off. Some views say its needed to keep out moisture or debris. After all these years I haven't had an issue with it off.
@grohy896 жыл бұрын
Great explanation dude. Thank you for the video. All the best :D
@AwkwardHamster6 жыл бұрын
+Matej Grohovac Thanks
@ofcbob63915 жыл бұрын
I am ok with staying with the standard bulb in my 2014 CRV but does anyone know if there is a way to keep the fog lights ON when switching on the bright lights? Seems like there is just no light up in front of the car, just way out there.
@wr63925 жыл бұрын
No vehicle allows the brights and fog lights to be on at the same time. You can't run high beam and fog lights together.
@tr4ilblazin7 жыл бұрын
So this don't need the moisture black thing that can't fit on the butt you said cause I can't use mine also
@AwkwardHamster7 жыл бұрын
+Ray Supra It doesn't need it. And I don't think you should use it because it would be pressed against the heat sink. Thus restricting airflow. LED has shorter lifespan if they overheat.
@tr4ilblazin7 жыл бұрын
AwkwardHamster okay bro thanks I was like worried lmao
@tr4ilblazin7 жыл бұрын
AwkwardHamster but moisture won't get in there ??
@AwkwardHamster7 жыл бұрын
moisture will, doesn't build up
@tr4ilblazin7 жыл бұрын
AwkwardHamster okay thanks bro
@ericheel16 жыл бұрын
my new led headlights stay on along with the DRL while the" car is running", When i turn on the headlight switch the only thing that happens is the DRL's turn off, This cant be normal, You think they may be defective ?
@tonychau19835 жыл бұрын
Does this blind on coming traffic?
@AwkwardHamster5 жыл бұрын
Not this one but I have reviewed some that do in the past. What I like about lasfit is they don’t try to advertise as being the brightest bulb. They took the time to explain why some of their bulbs are better suited for my vehicles make and model.
@tonychau19835 жыл бұрын
@@AwkwardHamster my brother got this and he told me to get a pair I just dont want to blind people. Got a 11 crv might retrofit morimotos in them not sure yet
@Armmani20006 жыл бұрын
Are they still working 2 years later?
@AwkwardHamster6 жыл бұрын
Yes.
@AURSN6 жыл бұрын
This led bulb no need canbus decoder for crv?
@AwkwardHamster6 жыл бұрын
Didn't need it.
@AURSN6 жыл бұрын
yeah i think only european car need.. thanx
@kencama2671 Жыл бұрын
My 2012 crv uses the headlight as a running light so led’s don’t work.
@louiebrilliantes96806 жыл бұрын
Is that the fan running on the background? That’s pretty loud...
@AwkwardHamster6 жыл бұрын
Fan is barely audible when engine is operational
@dcpc081619926 жыл бұрын
Honda CRV (like my CRV 2003...) has that pain in the rear wire clip :(. I prefer the insert and twist type of bulb installation much much better.
@Dalbertt5037 жыл бұрын
Great and very useful video. Thanks.
@AwkwardHamster7 жыл бұрын
+Carlos Rivas You are welcome
@JN-xd2np3 жыл бұрын
Which Honda CRV is this for? 4th gen?
@AwkwardHamster3 жыл бұрын
It’s from 2012.
@JN-xd2np3 жыл бұрын
@@AwkwardHamster thanks the reply! How is it lasting since? No flickering or lower dim? Does it affect the DRL aswell?
@AwkwardHamster3 жыл бұрын
It still works well. I’m glad I got this one for a few reasons. No flickering. I guess DRL is fine since it’s not that bright in the day and no flickering either. I am glad I didn’t get the brightest LED. It’s doesn’t blind on coming traffic.
@channawl57136 ай бұрын
Great teach
@patwrieck7 жыл бұрын
you did not put the rubber cover right?
@AwkwardHamster7 жыл бұрын
I did not put the rubber cover back on
@patwrieck7 жыл бұрын
AwkwardHamster thank's your video helps alot. :)
@Eric-hg1ih6 жыл бұрын
Does dust not get inside without the rubber cover?
@mrbobdog7076 жыл бұрын
I modified my dust cover to give some protection.
@dongordito00 Жыл бұрын
Thanks for this.
@AwkwardHamster Жыл бұрын
My pleasure
@Rendy.A.Nugraha4 жыл бұрын
Perfect cut off lamp
@mana11115 жыл бұрын
you can just twist the mounting plate off and install it, then install dust cap then push the led light through and twist to lock in place....
@reddog270ss7 жыл бұрын
does it flicker when the drl mode is on or does it function normal
@AwkwardHamster7 жыл бұрын
it does not flicker. also, my car didn't need a canbus relay. some european cars need it or the light will flicker.
@shawngixxer6 жыл бұрын
HI, what year CRV? Thanks
@AwkwardHamster6 жыл бұрын
+Shawn shawnZ 2012
@Knowledgexxxx5 жыл бұрын
1) seperate the adapter base and LED bulb 2) Fix the adapter base to original bracket.
@ps3boss986 жыл бұрын
5:06 The little clip thing or paper clip looking thing (whatever you wanna call it) wont go over my LED. I dont want to try to force incase I break it.
@tischlerbmw217 жыл бұрын
Don't like how there is no seal on the bulb, I bought a set of led bulbs and they are about the same,
@ericheel16 жыл бұрын
Thanks again.........................
@warlordbison7 жыл бұрын
Why do these LASFIT LEDs have such an acceptable cutoff, whereas other LED bulbs on the CRV look like a spotlight from hell?
@RichardsWorld6 жыл бұрын
Look at the design of this bulb. It is much better and purposefully built than the cheap ones. On the cheap ones you just see some LEDs mounted. This kit actually has some metal parts blocking where the light can go.
@annanguyen48398 жыл бұрын
thanks
@bizkid77 жыл бұрын
good video
@AwkwardHamster7 жыл бұрын
+bizkid7 Thanks
@kvmftOriginal036 жыл бұрын
"Now I'ma slide dis in.. Do it slowly, there's no need to rush." Proceeds to rush*
@СергейВолчков-к2ц6 жыл бұрын
У меня похожие лед они загораются с задержкой
@mkothari24 жыл бұрын
this is not a good solution without sealant - water/dust will ruin the led and headlight for sure ...
@yingjunluo19356 жыл бұрын
hey guy,we'll send you our product for free,could you make a product video for us?
@lifeisfunny97714 жыл бұрын
YingJun Luo i can make a video if i get it for free 2013 honda crv