How To Install Reverse Camera And Setup With Android Car Stereo?

Рет қаралды 202,177

Күн бұрын

Пікірлер: 112

@tingtingnoy3133 4 ай бұрын

Thank you bro, your the only guy who actually showed what wire to connect too on the actual harness, my camera hasn’t been working for 3 weeks now until I watch your video, been watched over 15 different videos and they all for some reason skipped over the most important fking step, what wire to connect too.

@aaronalquiza9680 7 ай бұрын

even if you're not a native english speaker, this is the most clear english instruction video for this topic that i've seen.

@Blaahvalz Ай бұрын

Thanks for the video! I did need to use the black ground wire to the chassis on my car to get a proper signal on the camera, but otherwise everything is working perfectly and the CANBUS automatically detects when it's in reverse. No need for any wires to the reverse lights. Appreciate the guide!

@Gg_blanco 26 күн бұрын

Thank you. Just what i needed. First video i found that explins so well.

@09014791 Жыл бұрын

If the vehicle has canbus does the reverse trigger wire still need to be wired to the reverse light to trigger reverse or can it be powered using the 12v ant blue cable on the stereo wiring?

@ragtopdodge Жыл бұрын

Canbus, don't need a reverse wire connection but still need to connect the camera wire to pin3 wire on the android radio

@Pittybizzle 2 ай бұрын

Great video. I would however recommend making a Y joint out of cable matching the power required. Using bullet connectors to join it all together, With female being the live end of connection. I have worked on a few cars where splicing cables has resulted in burnouts and in extreme cases, even fires. It is rare but always a risk.

@evgeshkagr 7 ай бұрын

Where is the connection to the rear light cable?

@awesome_slyda2059 11 ай бұрын

How does the camera know when youre in teverse? I didnt see you connect to the reverse trigger line

@Hellofa6ird 11 ай бұрын

0:52

@LukeOBrien-u8m 10 ай бұрын

Great video. I have a quick question on mine. I tried the brown wire on the stereo and even the pink one and no power coming to the light. Any suggestions please, would be greatly appreciated 🙏🏻 9:50

@ashykhan01 6 ай бұрын

hi there, if it’s an android unit then the wire is most likely located on your power loom side and this loom plug and its socket is normally labelled “G” and the wire is number “5” on your unit’s diagram. Therefore G5. This will be your Reverse/Back/Rear power cable. Hope this helps you. I’m still baffled at why he didn’t need to hook up the Ground (negative power) wire🤔 and how it worked without it🤔or is that ground already wired to the Ground wire within the RCA Cable🤔🤔🤔

@youknownothing3766 10 ай бұрын

Thanks for this, this is exactly what I need to do. Slice the power line into the 3rd wire.

@tingtingnoy3133 4 ай бұрын

That’s the one thing I needed, all the other videos don’t tell you what wire to connect too.

@g.o.a.t.entertainment9466 6 ай бұрын

Does your pink wire from the aftermarket wire harness also connect to the pink wire of the factory wire harness as to why you had to splice the wire in the middle as opposed to simply connecting and crimping the camera and aftermarket wire harnesses together???

@adamr6780 4 ай бұрын

where is 12v feed coming from? at the rear them red joint wires aren't wont be getting any current if they aren't connected to 12v power wire

@pomade34 4 ай бұрын

It seems that it is not nessecary if you have a CAN BUS

@gena2x_ Жыл бұрын

what did you use to cut the plastic off the wire in the beginning?

@Hellofa6ird 11 ай бұрын

Automatic wire stripper

@LukeOBrien-u8m 10 ай бұрын

Great video. I have a quick question on mine. I tried the brown wire on the stereo and even the pink one and no power coming to the light. Any suggestions please, would be greatly appreciated

@stanleyumeh6018 2 ай бұрын

Did u wire it to the reverse light. Sorry for the 7 months comment

@martinajuan2998 8 ай бұрын

is it possible to get the assist lines turn as you turn the wheel? second, is is possible to keep listening music while in reverse? thanks!

@obaidkhan9633 8 ай бұрын

Not sure about the guidelines turning but as for audio when I put the car in reverse the audio is muted automatically it you can turn it back up with the volume whilst still in reverse

@AntonioOrr 4 ай бұрын

My wire also is pink on the wire adapter and marked as backup camera but it is not working at all when put in reverse so I’m gonna check to see if it’s the 3rd wire if not I’ll connect to whatever the 3rd wire is and hopefully it will rectify my problem. Thanks for this video I’ve been searching for almost two months for an answer a this is closest I got I hope this helps me. I will come back to let you know 😮

@anima738 3 ай бұрын

Did you fix it? Mines doing the same thing

@ashykhan01 6 ай бұрын

great video, but was wondering, where does the black ground wire connect to???🤔🤔🤔

@hayden3865 6 ай бұрын

Put it under a screw in the chassis

@andresbernardi3685 Жыл бұрын

it's possible to watch through the camera without reverse? is there an app that can view?

@vp2777 3 ай бұрын

Good work ! Thanks for sharing

@armandk7036 2 ай бұрын

Amazing video. Thank you

@coldfirejones 6 ай бұрын

Super helpful, I was actually able to do this because of this video.

@jack.bauer.24 3 ай бұрын

Hi. I have K2401 android unit. Which connector is for automatic front view after reverse gear? There are video aux, camera in and cvbs cam in connectors. Which is for bumper camera?

@mon3628 5 ай бұрын

Is it always the 3rd cable from the top side?

@papabear007 6 ай бұрын

Question I have hooked up the wires in the head unit ran the wires back to the taillight I hooked red to the reverse light I did grown the black plugged the connectors in part but there is an extra red wire not sure so I just taped it up. But at the head unit I need to put camera setting on to use the back up not sure why? Could it be the extra red wire?

@grossmeister1181 9 ай бұрын

I have a different model of the head unit, where can I access that menu? There is no such menu on my device?! MT8163 it says, RS8577 also

@ravi911uk 4 ай бұрын

Is that 3rd wire a +12v?

@frostyfingersmtb9033 4 ай бұрын

Where do I find these settings in android 13 ??? Under factory settings there are few and non about the camera settings

@carloslence3764 4 ай бұрын

I have the same! Could you figure it out?

@shazzemperar 3 ай бұрын

I have no option for camera settings aswell! Please can someone help with this?

@LukeOBrien-u8m 10 ай бұрын

@Ahmad433 9 ай бұрын

Check if your reverse light turns on when car is in reverse connect the positive of camera to the positive of reverse light wires and connect positive to positive of reverse wire from the video wire as well hope this helps

@joanselten 3 ай бұрын

This is a very simple installation, but I prefer to route the cable better and also through the back door rubber instead of along it. Takes a bit more time but gives less problems in the future.

@gerietis4881 9 ай бұрын

Finally got connected, just after your video. So many on KZbin,but yours helpful, Thanks!

@TheCodeConnoisseur 6 ай бұрын

What does pin 3 do? Don't have any experience with electrics

@mrpaswal3909 7 ай бұрын

Very Helpful video Thanks 👍

@rusanyukaare179 Жыл бұрын

Thank you for this buddy but I am still trying to figure why mine is not working, I have attached the red wire from the camera to pin 3 I believe is Accessory wire at the back of android unit, at the back of the vehicle I have connected the video cable from the camera to the long cable connection and the connected the ground cable, red wire connected to reverse light. with all these but don’t get video, only trajectory lines. I have canbus and my unit is by T’eyes. Is there anyway you can help with diagnosis. Thank you again.

@MayBothwell01 Жыл бұрын

I’m having the same problem

@dimitrisiliopoulos2716 Жыл бұрын

Maybe connect the black cable to ground...The last one of the video

@AbinShaju Жыл бұрын

Even I'm having the same problem!!! @pluscenter please help

@kgonzalez6636 11 ай бұрын

Did you guys figure it out?

@Hellofa6ird 11 ай бұрын

Its not always the third wire on some harnesses, but it is always the third wire on the android unit. if you see a wire labelled "Back" or "Reverse" use it

@Davide-th4fs 9 ай бұрын

Hi, i've a mtk8163 with canbus and I connected the power to the third pin of the car radio. when I put the car in reverse the rear camera LEDs turn on but the video signal is not there. can you help me?

@jonnymercy4528 Жыл бұрын

the best video thank you

@pluscenter Жыл бұрын

I am glad that it helped you! ^_^

@ang8282 Ай бұрын

thank you brother

@shazboz Ай бұрын

When i put my car into reverse it doesnt even change to a reverse image. Just stays on the android auto page. What am i doing wrong?

@Case_ 6 ай бұрын

You really should use proper wire connectors and splicers in car installation instead of just twisting wires together and putting a bit of tape over it. That's just half-assing it and asking for trouble eventually.

@MACSauce-xf6qu 4 ай бұрын

I’ve been twisting and taping 20 years never 1 came loose

@Case_ 4 ай бұрын

@@MACSauce-xf6qu Look up "survivor's bias". (And I guess also "professionalism" or something like that. Twisting wires together and taping them is just half-assing it, period.)

@ovhfryerr6934 4 ай бұрын

As an electrician I can tell you that a simple twist to splice it is more than enough, especially if you choose to put a wire nut on the splice

@Case_ 4 ай бұрын

@@ovhfryerr6934 As an electrician, if you're twisting wires together, you're half-assing your job and you certainly shouldn't advocate for doing it. And don't get me started on wire nuts Americans in particular seem to love so much.

@neilenriquez8678 4 ай бұрын

Spliced then solder and shrink tube thats how I do wiring..and not exposing cables ..will use guide wire to insert and snake thru that flexible conduit..

@antbliss1471 4 ай бұрын

hello can you help me i can’t get my camera to work in my 2014 caddy,there is a wire on mine that says camera + so tried that and nothing and also i tried the 3rd wire from the top that goes to the can is box and still nothing

@mantasjapertas1096 7 ай бұрын

I have connected and done everything to the video the camera works for a little and then loosing signal . If I start the van it looses signal straight away… any ideas ?

@mortezaashrafi6983 4 ай бұрын

You didnt use positive reverse light trigger, is that gonna work for every car?

@MR-zl6vs 3 ай бұрын

Don’t work like this for my car

@steffenwolffe507 7 ай бұрын

what is it with videos not having enough volume? If I crank to 100 (to actually hear this) when the YT ads come on, kiss the speakers good bye... as such, good bye til you fix the audio, and I look elsewhere for the same info put out by someone that knows how to manage audio levels.

@pontusborgjonsson1246 10 ай бұрын

So you dont need the ground or take power from say reverse lamp just lut triger on red and its get power from stereo fron the videocable cool

@lucky_luc_1999 9 ай бұрын

Yeah i was thinking that too only connect to the pink back cable in the radio and connect the two red cables at the camera and it works?

@pontusborgjonsson1246 9 ай бұрын

Yes it does i dont use reverse lamp i have pigtail from rca cable on red power leave ground no need the. Pigtail from stereo trigger tada all done

@lucky_luc_1999 9 ай бұрын

@@pontusborgjonsson1246 that would be perfect i think its because the RCA already has a ground inside?

@pomade34 3 ай бұрын

Merci ça m'a beaucoup aidé.

@pasangwangdi-leo93 5 ай бұрын

We dont have to connect it with the reverse tail light wire??

@coreyboles1064 5 ай бұрын

I guess depends on radio unit you have

@zayturner5075 11 ай бұрын

Whats the pink wire exactly?

@imrantazim2688 9 ай бұрын

Would an original factory fitted reverse camera be compatible with these android head units ????

@alzyonline 5 ай бұрын

Did you get a reply to this? I've got an original camera that I'm trying to connect. I haven't tried wiring in the power yet, that'll be the next step.

@imrantazim2688 5 ай бұрын

@alzyonline yes I got a reply! I bought the following reverse Cambus / Adapter, for it to work with these after-market android units. I must state the quality of the reverse camera with this cambus is poor. Hence why I've returned the whole unit for a better operating unit.

@alzyonline 5 ай бұрын

@@imrantazim2688I've got a different head unit, I've bought the adapter, I haven't wired in the red wire that he taps into the pink wire, I think that's all I'm missing. Will give it a try this evening or tomorrow.

@marcmatute1571 4 ай бұрын

You are a god

@lv8097 3 ай бұрын

Thank you man

@humandisorder3962 18 күн бұрын

3:36 Mercedes Benz plate 23 and corrosion 😮😮😮😮😮

@Bihigh 10 ай бұрын

How do you get passcode?

@TheCharliemcgarry Жыл бұрын

I’ve got the light on the camera working but no image is showing on the screen. What could I have done wrong

@pluscenter Жыл бұрын

You must choose the right camera format from the stereo settings, thanks!

@TheCharliemcgarry Жыл бұрын

⁠@@pluscenterI’ve tried it on all the different settings and with the video in connection and video out, it just comes up saying no signal

@pluscenter Жыл бұрын

@@TheCharliemcgarry make sure it’s connected to the 3rd wire to the back of the stereo.

@TheCharliemcgarry Жыл бұрын

@@pluscenterit is, it’s brown on my head unit, that connects to a black box which has 3 white boxes on the end. 1 smaller one which connects to a connector in the van already and the 2 bigger ones have no where to connect to

@milehodak4152 2 ай бұрын

I tried this step by step with my new android screen and is not working for me. Any idea why would that be? I just get no signal when in reverse, and tried to switch to ntsc and pal and everything

@johnmichler4162 2 ай бұрын

I also have the same issue and cannot find any videos to address the problem. If anyone knows can they reply to this post? Could it be the camera itself?

@milehodak4152 2 ай бұрын

@@johnmichler4162I found a solution

@milehodak4152 2 ай бұрын

@@johnmichler4162 I was connecting camera cable to cvbs cable that was with the bunch of other aux cables , but it was supposed to connect to another one separated from the rest