How To Install Roof Flashing

  Рет қаралды 556,789

Deco Bliss

Deco Bliss

Күн бұрын

Пікірлер: 72
@droidb5464
@droidb5464 Жыл бұрын
Wondering as a simple DIY er , can you use the liquid lead type filler that comes in tubes , to secure it in/seal it rather than just cement pointing ? Is it beter or no to do that ,Can anyone advise me please?
@Davey14
@Davey14 12 жыл бұрын
Im a 3rd generation roofer with 26yrs exp.If a felt roof has more that 15 degree fall then the felt must be nailed but you shouldnt be able to see the nails.The nails go on the salvage along the edge of each sheet and are covered by the next sheet and the same gets done along the verge before the verge flashing is fitted.If this isnt done the felt will slide and wrinkle in extremley hot weather ;o)
@neilgallacher4793
@neilgallacher4793 3 жыл бұрын
This told the middle of the story really well. Shame it forgot to have a beginning and an end!
@travisp6459
@travisp6459 11 ай бұрын
Would you use use a sharp sand mortar mix to fill in that void after the flashing is secured and clean up with a sponge for a nice finish?
@GeorgeBoateng-r6r
@GeorgeBoateng-r6r 3 ай бұрын
Great stuff - I wish all roofers were as diligent!
@DeeCartwright
@DeeCartwright 2 жыл бұрын
How lovely, simple and clear. Thank you. 😊
@caileanmoore2835
@caileanmoore2835 11 жыл бұрын
Lead being tucked into the cut chase should return up inside it like and L shape and be fixed with brass screws, washers and rawlplugs. Read the Lead sheet manual,this is the recommended method. Cutting and chiselling in lead straps damages the lead! The chase should then be sealed by first brushing on a mastic primer and then using lead sheet sealant. I've been doing leadwork for 35 years as a plumber. Just because you can torch on a bit of felt, doesn't mean that you can do leadwork too!
@houlhersteady
@houlhersteady 11 жыл бұрын
I have to agree 100% , it always chancres who post videos on building trades. This guy is simply a first class chancer.. The section of lead that goes into the wall should be at least 40mm have a upturn on it to stop water perpetration in to the mortar. He then puts one lead wedge in place and knocks the s...t out of , causing the lead flashing to buckle. It not rocket science, you place all your wedges in place and tap them gently in rotation , till they are sweet.No need for brute force
@robrotin9760
@robrotin9760 10 жыл бұрын
Appreciation for the nicely proceeded roof flashing installation. Everything is done properly by making it sure that there's no lag in the work done.
@PeakyBlinder
@PeakyBlinder 13 жыл бұрын
did you bend the lead round that arial pole to form the lip ?
@jayp5966
@jayp5966 2 жыл бұрын
The gap between the brick and lead is ok to be left like that?
@justbreakingballs
@justbreakingballs Жыл бұрын
Obviously you point up
@MultiSpread
@MultiSpread 12 жыл бұрын
Great job mate very professional
@jeztickles4361
@jeztickles4361 4 жыл бұрын
What did you cut that chase with? A shotgun??
@dean6125
@dean6125 8 ай бұрын
😂😂 (old post I know)
@newjerseyray
@newjerseyray Жыл бұрын
with no roofing cement under the flashing, the water will still flow into that gap and then under the flashing no? I don't see anything to prevent that. is the flashing here just a mechanical protection of the roofing felt under it?
@mrboyban
@mrboyban 7 ай бұрын
Watch the video again. He did mention that is how you install the lead flashing and also mentioned to fill it up with mortar "to make as watertight as possible", but hey if you skip the video you can no blame anyone other than yourself.
@jhonkamak2094
@jhonkamak2094 9 жыл бұрын
Thanks for your video mate
@JohnnyHurst
@JohnnyHurst 12 жыл бұрын
You should have put a spring clip on the top of the counter flashing. Might have been better to use termination bar on that particular wall.
@arip9234
@arip9234 4 жыл бұрын
Impressive young man
@Degenerative1
@Degenerative1 9 жыл бұрын
Great work fella.
@Listermintsluesh
@Listermintsluesh 6 жыл бұрын
Nice vid well explained.. need mine doing soon lol
@blizteredthumbs7911
@blizteredthumbs7911 Ай бұрын
Excellent 👌.. no nonsense, mucking about, stupid music.. just a proper heads up video, straight to the point. Today's KZbin? This would be 25 minutes long and here is a word from today's sponsor as well as stupid audio drowning out anything you're saying.
@1441sweet
@1441sweet 12 жыл бұрын
nice i need to do tht job and give me very gud good ideas
@stuartmountjoy4934
@stuartmountjoy4934 11 жыл бұрын
That's how you install a lead flashing eh? Bugger I've been doing it wrong all these yrs then mate cos I tend to knock the 'bungs' in not tickle em. Also you stated 25mm into your chase but that flashing was hardly into the wall, no nip 'n' tuck on your side lap, patination oil is a nice idea... and point the wall up, assuming your not talking compo?
@big.a1131
@big.a1131 4 жыл бұрын
Use stopeid lead sand and cement better job
@asifbashir5573
@asifbashir5573 2 жыл бұрын
Felting a side extension
@1973stewy
@1973stewy 12 жыл бұрын
Surely your having a laugh. Where is the worm on the lead flashing, also were is the paper? Moisture will penetrate and run in behind that flashing no doubt about it, this guy gives a cowboy roofer a good name
@jhonkamak2094
@jhonkamak2094 9 жыл бұрын
Thanks for your video meet
@sqwidink1
@sqwidink1 12 жыл бұрын
lead sheet sealant, will do the job.
@olitonottero7620
@olitonottero7620 5 жыл бұрын
it looks good but in general it last about one month before it gets stolen :) lead-free is the way forward , it's cheaper lighter and some of the brands now come with 25 year guarantee
@sjiroofingandmaintenancese2494
@sjiroofingandmaintenancese2494 5 жыл бұрын
Olito Nottero it’s shit , tramps use it not real roofers
@Will-nb8qk
@Will-nb8qk 2 жыл бұрын
lol 😂 Is lead expensive?
@northeastcorals
@northeastcorals 2 жыл бұрын
@@Will-nb8qk Yup
@the_general_1
@the_general_1 9 ай бұрын
This is so wrong. Not deep enough and no curl at the end. If this is the rainy side of the building, it should even be behind the inside brick
@tonyukusa1
@tonyukusa1 11 жыл бұрын
please protect your self from lead , my father and grand father both died from lead poisoning.
@jhonkamak2094
@jhonkamak2094 9 жыл бұрын
Why they plying music
@zol404
@zol404 13 жыл бұрын
looks good
@Roofer89
@Roofer89 3 жыл бұрын
Not a blead in sight on that felt leaker
@liammcaogain2001
@liammcaogain2001 7 жыл бұрын
How can so many so called roofers get led wrong going into the brick
@DistractionCascade
@DistractionCascade 8 жыл бұрын
32 down voters are floor installers
@Jonnydog1
@Jonnydog1 9 жыл бұрын
Alter title to 'How not to install lead flashing' and this video would be all correct.
@girlinagale
@girlinagale 12 жыл бұрын
Seems the sarcasm and criticism comes from the US. In Britain we get on and do the job, in the US there's too many on KZbin trying to be superior about how it's done. Churches are only good for the lead.
@jonnydanger7181
@jonnydanger7181 3 жыл бұрын
Lots of issues here; 1. The modified bitumen wall flashing is not nailed off. Big head concrete nails in to mortar must be used. 2. How are you addressing the gap between brick and lead? water will go behind and rot the brick. This job needs rejection.
@Toyotaamazon80series
@Toyotaamazon80series Жыл бұрын
He said at the end that the gap will be pointed with mortar.
@sexyslater4443
@sexyslater4443 9 жыл бұрын
Dude go to college!!! Well recommended!!!
@houlhersteady
@houlhersteady 11 жыл бұрын
contd ..Most professional tradesmen would cover the area of roofing with a plywood sheets or dust sheets to prevent damage to the new felt surface. Felt membranes are easily damaged scratched etc , and theirs nothing looks asbad as a new green mineral felt roof with scratches , dents etc. Their are professional out there who are masters at this work , but sadly they never ever post videos of their work. Manufactures should post videos using only highly skilled tradesmen. It in their interest.
@michaelledford4751
@michaelledford4751 7 жыл бұрын
mulders drift I'm retired from the 3rd largest commercial and industrial roofing company in the USA with sales of $75 to $120 million a year ,we don't post videos of our work because a small job for us is 1,000 squares and it's got 40 men working on the roof ,for my son's high school wood shop project I took my son to work with me so he could make a video demonstration of " How To " from start to finish ,it took him filming for 5 days on a 1,200 square tear off to capture tear off ,deck replacement,itnstallingnstalling a base layer of insulation ,then a tapered insulation system , tuck pointing bad masonry before flashing over , rebuilding several rotten chimneys ,installing the roof and dozens of details like pitch pans ,soil pipe leads ,lead roof drains etc before we even got to installing the final layer of cap sheet ,itnstallingnstalling turned out to be a 4 hour epic lmfao ,if I could figure out how to put a VHS tape on KZbin I'd download the thing .
@jamiewatkinson4123
@jamiewatkinson4123 3 жыл бұрын
That's not long enough
@jwhandjr
@jwhandjr 12 жыл бұрын
Ja
@kennyyellop
@kennyyellop 11 жыл бұрын
why is it that all roofing vids on here are made by chancers
@the-colonel9809
@the-colonel9809 11 жыл бұрын
Not really a roofers job? unless you can find a plumber who is over 100 years of age from back in the days when plumbers used to do lead work. Ask a plumber now how to lead dress or weld and they cant they all claim to know until you ask them to do it.
@PeakyBlinder
@PeakyBlinder 12 жыл бұрын
3:27 what a fucking mess
@chalkycliff4068
@chalkycliff4068 6 жыл бұрын
Roofer wants to charge 500 odd quid just for this
@ddk4664
@ddk4664 5 жыл бұрын
Scafolding and material where probs £1000 so id take £500 lol
@williecummins2260
@williecummins2260 2 жыл бұрын
Winddriven rain will go through the brick and down behind the lead eventually,crap job.
@lmackenzie9198
@lmackenzie9198 2 жыл бұрын
I agree Willie.
@robertomete
@robertomete Жыл бұрын
Hmmm not bad
@UncleStonks
@UncleStonks 12 жыл бұрын
Nails? Through waterproofing? Good job you're not a roofer.
@stuartevans4748
@stuartevans4748 11 жыл бұрын
Not really a Roofer's job though, really a Plumber's, leadwork surely?
@stevehunter7062
@stevehunter7062 3 жыл бұрын
Get back in your office stuart
@jwhandjr
@jwhandjr 12 жыл бұрын
Wu. Ahwiroshei,towiwyak
@mikebryant3901
@mikebryant3901 4 жыл бұрын
Pp
@markknowles58
@markknowles58 12 жыл бұрын
them bungs as you call them are shocking wouldn't let you flash a dogs kennel
@TRPGpilot
@TRPGpilot 11 ай бұрын
Inches> Nahhh. I stopped and looked for a video with metric units.
Calder Lead - Apron Flashing
9:01
CalderLead
Рет қаралды 364 М.
Installing or Repairing Lead Front Apron Roof Flashing
6:13
Dave Salter
Рет қаралды 34 М.
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН
When you have a very capricious child 😂😘👍
00:16
Like Asiya
Рет қаралды 18 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 56 МЛН
How To Install Drip Edge On A Roof
6:49
Your Average Roofer
Рет қаралды 1,7 МЛН
How to Install Lead Roof Flashings - Easy fit roof flashing DIY
10:42
The Millennial Roofer Teaches Counterflashing
15:44
Restoration Referral System
Рет қаралды 189 М.
Timmertip 464 Onderhoud aan lood in muren aangebracht
7:16
timmerman koos
Рет қаралды 176 М.
Roof wall flashing, what not to do
7:52
Grand Roofing Inc.
Рет қаралды 41 М.
Lead step flashing
5:00
Easy flash
Рет қаралды 239 М.
U.S. PLY How to - Torch Application Techniques
10:07
ModBitRoofing
Рет қаралды 1,8 МЛН
How to Install Step Flashing | Shingle Roof Install Guide
6:30
Roof Repair Specialist
Рет қаралды 63 М.
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН