You left out a very important part. You didn't talk about the washers on the head pin. The instructions talk about how different washers to use depending on how many inches. But, inches of what?? The instructions don't clarify.
@cindygroniger1706 Жыл бұрын
Just the information I was looking for. Thank you very much.
@jeromesmith12433 ай бұрын
Are you measuring the ball coupler to the top or bottom
@dg74325 ай бұрын
Is load popping noise normal on these?
@BrianSmith-si4zd5 ай бұрын
Yes that normal. When you turn the bar comes off the bracket when you straighten up it makes contact again . Thats how I install them actually no tool needed.
@dg74325 ай бұрын
@@BrianSmith-si4zd thanks bud.. showing this to the wife..
@raptracktv60294 ай бұрын
Yeah sounds ugly too but it’s completely normal
@raptracktv60294 ай бұрын
@@dg7432my wife was freaking out when she started hearing the popping noise
@dg74324 ай бұрын
@@raptracktv6029 after 3 years of having ours. The wife still freaks out. Definitely a head turner in the rv parks
@yamaguyАй бұрын
Can you bolt the brackets directly to the frame? I have a toolbox that is factory welded to the frame where the brackets go.
@BGCONTRACTINGLLC Жыл бұрын
How high do you set the trailer to determine the load bar brackets?
@Chevy243 Жыл бұрын
Question I need to pick up my new trailer from the dealer and I need a weight distribution hitch but can I just install the hitch part to take it home it’s about a 30 mile drive from point a to point B?
@JohnMaldonado-kf2pm Жыл бұрын
depends on your weight of all equipment involved. the ball part of the hitch without the bars is rated for 600lbs tongue 6000 lbs trailer weight. look up centerline ts manual and front page of manual says so
@AllenBennett-l2g3 ай бұрын
@ottodealerventures9510 For some reason it will not let me reply to your question. So here is what I have, it's is not cheap, bought this from Amazon and it is quality. Performance Tool M204 3/4-Inch Drive Torque Wrench with LH/RH Thread Torque Capabilities - 100 to 600 ft/lbs of torque
@timclosson716628 күн бұрын
I did so much enjoy the results! Great job!
@ottodealerventures95105 ай бұрын
What torque wrench are you using? I’m having a hard time finding something to do those specs.
@AllenBennett-l2g3 ай бұрын
After I made my own comment, now it lets me reply.... Performance Tool M204 3/4-Inch Drive Torque Wrench with LH/RH Thread Torque Capabilities - 100 to 600 ft/lbs of torque
@normandbrunet9284 Жыл бұрын
id like to know why the frame brackets needs to be installed with spare holes underneath the frame and not on top
@roughme7409 Жыл бұрын
Hello, are the spring load bars interchangeable from 600-800lbs to a 400-600lbs for example using the same assembly? Thanks
@JoeyComs Жыл бұрын
Yes, the 600-800 and the 400-600 are interchangeable using the same head assembly
@jc80 Жыл бұрын
I just installed this on my Nissan frontier. Empty my front wheel base was 34" and rear was 34 5/8". Now with the trailer they are both 34" and the trailer is almost completely level, has 1/2" tilt to the rear. Does this sound correct? We figured we would have a couple people in the truck and 100lb of stuff in the bed. Also, when backing up it clanks sometimes, is this normal?
@JoeyComs Жыл бұрын
Yes, this is within tolerance.
@Steven-ym3mn Жыл бұрын
The clanking is just the friction
@JasonPhipps4 ай бұрын
If it's clanking, it's working. When it's not clanking or popping, especially in a turn, that means it's lost friction, which is your ability to alleviate sway.
@remogalaz974410 ай бұрын
My hitch is upside down dose it make a difference
@JoeyComs8 ай бұрын
If you are referring to the shank portion that slides into the the receiver, it is designed to go either way depending on your hitch height.
@suzyfueshko9593 Жыл бұрын
What do I do if the measurement at the tongue in more than 1/4 to 1" higher? My trailer is also 1 inch higher in the front when hooked up to the truck, what should I do?
@huskytowing Жыл бұрын
Hello, our tech team will be able to answer this question and any additional follow up questions! You can call them at 877-544-4449 M-F 8-5 EST.
@ericbarrett10303 ай бұрын
Better question is why would the frame be higher after installation? Wouldn't that make the trailer be nose high?
@michaelwebb6285 Жыл бұрын
Our husky hitch is really loud when going around corners is this normal?
@huskytowing Жыл бұрын
Hello, our tech team will be able to assist in why it is making noise. You can call them at 877-544-4449 M-F 8-5 EST.
@ianmellors7061 Жыл бұрын
Our hitch is very loud as well, can I use the number above to call from Canada?@@huskytowing
@Steven-ym3mn Жыл бұрын
It’s normal mine does the samething…it’s the friction causing the noise it’s normal