Merillat not only make great products, but they are really fine jewelery. Never seen better welds in my life. Made in the USA in my home state of Ohio I believe.
@extremerodsandracers Жыл бұрын
I've been struggling with getting the lowers out. This video helped me a bit. Thanks you
@rongravel45854 жыл бұрын
Annnnddd instant subbed. You guys ain’t no dummies. And that set up is definitely art. That guy is nasty. I wish I was that good
@robertclymer69483 жыл бұрын
Watched the whole video. It was very nice to see a couple of young fellas that were not hacks. They did a hell of a good job and did not cut corners. Thanks for sharing with us Mustang folk. Cheers from Motown!
@joe5.0434 жыл бұрын
So glad I found this video !
@Dubliner484 жыл бұрын
Nice job Nigel. Can't believe you guys have been running the stock boxes for so long. Especially with the ET's and 60' you guys have put down.
@gumby4422 ай бұрын
Beyond my skill level 😮.
@Stevesbe3 жыл бұрын
I remember when those cars were new my friend had 85 t top car . He basically ripped the whole rear out the car power shifting it and it was stock
@berardoferrari3 ай бұрын
not a chance! mine makes over 500 plus to the wheeles. never had a problem, but i dont drag race.
@jameskilpatrick60864 жыл бұрын
I pulled a tape measure from the rear of the lower boxes to the centerline of the front lower A frames holes to insure they were lined up the same on both sides. I do know aftermarket upper and lower control arms are adjustable but I like to be sure everything is square rather than reference points.
@samuelmariscal45564 жыл бұрын
How much do you guys charge to do this?
@randylanhart17964 жыл бұрын
It's like watching the movie spun! I was waiting for Mickey Rourke to show up.
@reactiondc24 жыл бұрын
Great video, definately going to help me at a later date!
@robvandam544810 ай бұрын
Haha... yall used the Visa Grip Garage theme song Shout out to Derek
@thestickcahhhh4 жыл бұрын
Really been enjoying the channel. Could you go over suspension setup as far as what holes to start with on the Merillat boxes and show what your method of squaring up the rearend in the car is?
@nigelstst4 жыл бұрын
thedoc612 we appreciate the support. We just ordered a rearend form Marty so once we get to that point I’ll try to remember to make a video with our starting points.
@hebertbuilt20754 жыл бұрын
Great video.. definitely needed this.
@jameskilpatrick60864 жыл бұрын
Cutting the lower torque boxes out to me were not as hard as cutting out the upper. I cut the crap out of the stuff with a 4-1/2” cutoff wheel to get to the hard to get areas. Not bad. Also, you guys should consider buying you a nice mig if you’re going to do more fab work. I have a miller mig and tig. I welded in the upper in less than ten minutes. I have a lift and even with it this is hard,strenuous work especially on the back.
@peterkay24063 жыл бұрын
Great video, you mentioned to measure to make sure both are installed evenly, but you never showed where to measure, on the upper torque box in super high speed I seen a quick flash of you measuring but couldn't tell what or where you were measuring? Can you describe where to measure and what kind of measurements we should be getting?
@nigelstst3 жыл бұрын
Unfortunately it’s been so long since I did this I don’t remember the details. I’ll try to watch that part again later and see if I can figure it out
@Ls3guy4 жыл бұрын
Good job guys
@Steve0newsome4 жыл бұрын
GREAT video!
@petejoseph82573 жыл бұрын
So, it takes 2 guys 10 hours to get get old stuff out?
@mustangtez40604 жыл бұрын
Can you guys please share the rear end length and the wheel size, offset and backspacing. I need my car to sit just like this.!! Stance is killin the game.!!
@nigelstst4 жыл бұрын
46” end to end 15x12 4” backspace
@mustangtez40604 жыл бұрын
@@nigelstst thanks man I appreciate it.!!
@mustangtez40604 жыл бұрын
@@nigelstst oh and the offset.?
@nigelstst4 жыл бұрын
Backspace and offset are almost the same thing. When we ordered them offset was never a factor. I think one directly effects the other so we just worry about backspace when we order drag wheels.
@mustangtez40604 жыл бұрын
@@nigelstst 10/4 thanks again.!
@TheCobraSlayer4 жыл бұрын
2JMFAB, How do you know those guys? They build some badass cars!!
@nigelstst4 жыл бұрын
They spec’d our coilovers on the shop Foxbody and we’ve sent a lot of people their way. Great people
@brainward2611 Жыл бұрын
What kind of price would it be to have this job done
@charlesgreer76414 жыл бұрын
Are these just for drag racing or can I use them in a street car lowered with wide tires all 4 corners. Reason I'm asking is my top passenger box is ripped away from the unibody of the car. I was going to reinstall and reinforce them but the more I think about the level of damage I might as well replace with aftermarket boxs. And adjustable control arms.
@spassmore84834 жыл бұрын
you can run them on a daily driver street car it will make it handle much better too!
@alialdoseri73634 жыл бұрын
I did mine and it wasn't fun but the results was worth it
@jesusmunoz51844 жыл бұрын
Did you section the floor to weld the back side?
@jesusmunoz51844 жыл бұрын
Did you section the floor to weld the back side of the uppers?
@alialdoseri73634 жыл бұрын
The trunk area only
@jesusmunoz51844 жыл бұрын
I figured. If you spend money on such a great piece, might as well do it properly. Thank you for the info.
@danielbargas33774 жыл бұрын
How fast have you gone on factory torque boxes? Great work btw 👍🏼
@dclsxfactory78233 жыл бұрын
I found this video because i was lookin for tips to get mine chopped out and replaced, but i been 1.05 60’ 4.58@153 at 3200lbs in ultra street trim in my car. I replaced the bent bolts a few times but torque boxes look ok. Im just looking to lower the car a few inches to get crank center line down to stop the wheelies and no way to get the instant center right with the stock holes
@stevenmcc21192 жыл бұрын
Slip or never happened
@averystuckey83312 жыл бұрын
What would it cost labor to do it
@thomascampbell76310 ай бұрын
What’s it cost to replace the TQ boxes?
@nigelstst10 ай бұрын
Usually $1400-2000 in labor plus parts.
@Thief40010 ай бұрын
I’m guess you guys haven’t heard of a plasma torch!?!?!? Get one
@nigelstst10 ай бұрын
At the time my only plasma torch was on my CNC plasma.
@angry408w74 жыл бұрын
wow they work fast lol
@atonyrodify3 жыл бұрын
GREAT CONTENT GUYS !!just subscribe to your channel thanks to (FULLSPOOL)HOOE TO SEE MORE VIDEOS LIKE THIS MY SON AND I LIVE THIS STUFF TILL NEXT VIDEO BE SAFE HOOE TO SEE MORE VIDEOS IN THE NEW YEAR
@rampage25874 жыл бұрын
Where did you use for your reference measurements. Factory holes in the subframe or did you just measure and make marks wherever.
@nigelstst4 жыл бұрын
These boxes are made to match up with certain parts of the frame we just clamped them in place and took measurements from a point on the car to ensure they were even.
@rampage25874 жыл бұрын
@@nigelstst thank you good to know. And awesome job.