HOW TO JIMNY [ Replacing the rear wheel bearing at home or in the bush ] **With ABS**

An easy, cheap guide to changing the rear wheel bearings on your jimny
Link to axle seal replacement:
• HOW TO JIMNY [ Replac...

[@Joshhy95]

Just found my leaky oils seal needs doing after replacing a good one after doing a diff swap so will do bearings while I'm at it, great tutorial mate! Nice and detailed yet simple and to the point.

[@jimnythings2410]

Thanks mate, good luck with yours 😄

[@Joshhy95]

@@jimnythings2410 thanks mate ! Did a bit more research and I think my bearing is flogged which has caused it, lots of in and out movement along with lots of noises. Shall be fun 🤣👌

[@patrickdwyer9368]

Awesome video. About to remove my rear diff centre so a lot of this is necessary to do that as well. Now I’ve seen this video I will replace both rear bearings while the diff is at the shop. Thanks heaps from Moorooka, Brisbane Southside

[@guyems4490]

Thanks for the video mate ! Very helpful. Regards from South Africa 🇿🇦

[@bennixon6093]

Best video av found to follow will be doing mine now 😂💪

[@jimnythings2410]

Good luck and buy a reasonable sized hammer 😂

[@michaeldalton3604]

Thank you for this epic guide, just finished doing this myself thanks to this video. Will just note that in my case the 32mm diameter tube didn't fit over the axle, so had to use punches but other than that appreciate all the info!

[@jimnythings2410]

That’s strange the tube wasn’t right for yours, but glad it worked out in the end 😊

[@sergiovega2662]

very good I learned one more… thank you very much, directly from Brazil 🤘😎

[@thebubaloomonkey]

Nice thorough video! On my non-abs model I make the cutting part easier by cutting through the bearing outer race first, which then allows me to slide the back plate off and out of the way before cutting the retainer. I don't think the backplate clears the tone ring on ABS models though? The inner race then normally hammers off.

[@danieljackson4171]

I recently swapped a (2022 jimny 1.5) rear differential with a (2015 jimny 1.3) Unfortunately the 1.3s differential is 3cm shorter than the new 2022 jimny 1.5 in emergency situations or when there's no money to buy a mew diff one could swap and end up with small minor abs sensor differences and if you split the 3cm from both sides you end up with 1.5cm difference shorter differential length wize from both sides.(it works fine ) The rear differential shafts are not the same lengths if you want to swap only the side shafts. Meaning swapping the entire rear diff is the preferable modification

[@SalvoDan]

I'm wondering if you have Extended Diff Breathers. While they primarily prevent water getting into the diff housing, they also serve the purpose of preventing the factory diff breathers from failing. If the diff housing can't breath, the sudden cooling of a water crossing will cause it to try and suck in from the wheel bearings.

[@shinabhe]

I have problem with my jimny. I hope you can give me ideas or advice on what to do. This is what happen. I parked my jimny and after a day i tried to use it. so start the engine, stepped on the brake put my AT gear to reverse and released the handbrake. It won't reverse. The other rear wheel is already spinning but the one on the rear right wheel wont turn. so I jack both rear tires and tried turning the right wheel. It feels like a locked steering wheel where it only turns half inch left and right. and when I tried to remove the tires. It so happen that one of the lug nut got busted so I used a nut removal tool and when I hammer it to the busted lug nut the wheel suddenly turn freely. So the hammering fixed my problem. But I want to know what might have caused this problem? what can I do about it? thank you so much for the videos it helps me a lot with my little jimny.

[@awtistiaeth4699]

Brilliant, thanks a lot. Love the make shift slid-hammer! Is it possible to do the input shaft bearing in situ? Just purchased another Jimny and the rear axle growls gently all the time. Not sure if it is wheel or input shaft so may just do all three.

[@jimnythings2410]

You mean the diff pinion bearing?

[@awtistiaeth4699]

​@@jimnythings2410 Thanks, yes I do.Mind you, I have 2 jimnys for parts, so I may just swap half-shafts and diff from a scrapper into my existing case. Mind you, if the diff bearing comes out easily, I could replace with a new one and just swap half-shafts with bearing retained on them (they are good, I used to drive the car they're coming off)

[@JuanMiltonGonzales]

Well done !!!... saludos desde Perú . Quisiera saber tu expericiencia con esta camioneta . Has probado la la nueva Jimny?

[@thebrother987]

good job

[@YOWIEONERZ2007TWD]

Did you have to bleed the brakes after the install mate?

[@GERfusion]

Great video's I've subbed 👍👍. Any advice on reinstalling the half shaft? I was hoping you was going to do a video on the reassembly. What's the best way to put the shaft back in does it take much force to push the bearing back into place? If so what's the best way of doing it?

[@jimnythings2410]

Just line it all up and push it in. Get it as far in as you can by hand then smack it with a soft hammer or a hammer and a a bit of wood

[@timothyrichardet2543]

Are the parts the same for a1999 grand vitara.

[@Ouwkackemann]

Hey, thanks for showing. What I don´t understand is, why the bearing has a gearwheel? What is that for?

[@jimnythings2410]

This is a tone ring. It’s only on the abs model. Pre abs will just be a small collet in place of the “gearwheel”

[@bergzi99]

do you have any tips for EGR valve cleaning on the jimny? do you need to remove it or is it enough to spray a cleaner into the air intake?

[@jimnythings2410]

You need to remove it to clean it. I have never personally done it though

[@MuniNadan-rk4jd]

Nice video mate. It's not that easy job either. Jimnys are fun but pain to repair

[@Macos9966]

Ótimo trabalho

[@monkey_with_a_skateboard6823]

Do you think it would be worth using a good quality waterproof grease when refitting to try and help keep the shit out?

[@jimnythings2410]

Probably not mate. Grease will hold onto all the dirt and make it worse. And if you put it on the outside of the seal it will go through your brakes

[@monkey_with_a_skateboard6823]

@@jimnythings2410 fair enough!

[@bennixon6093]

Another really helpful video thank you 🙏. Any over social media to follow you on

[@jimnythings2410]

I’ve got an Instagram account also called @jimnythings

[@bennixon6093]

@@jimnythings2410 👍👍

[@mfs8328]

спасибо братан!

[@Ouwkackemann]

Ah, now I see, the bearing sits on the axle and is not pressed into the diff housing, that´s great.

[@tompage8438]

Boy I wish my wheel bearings came off as nicely as yours. Shitest job I've done on my car

[@ОлегЧупрун-ь6ы]

Витаю. Україна.