How to make a LAWN TRACTOR into a FLAMETHROWER !

[@hfd6ygf785]

put turbo in lawn mower😂

[@azurtayt1440]

Make this top comment

[@SajonWalker]

Believe it or not, these opposed twin engines, sound amazing when you put a turbo on it. They almost sound like a 12 valve

[@williamcooper2095]

I would love to hear it with a turbo, would be awesome

[@pascalschumacher777]

Jeje and leave the sparkplugs in for antilag xD

[@Coolengines]

Two turbos

[@Turbowagon]

Hook up a 12v coil on a switch to the exhaust plugs and have it also kill ignition when you flip it then hold the throttle wide open and hit the switch. Doing it this way you can have a steady flame for a few seconds while you hold it. You can use a relay to ground the ignition kill when it sees 12v signal from your switch.

[@M.TTT.]

this is it

[@PorousShark7688]

Here is a idea you can do to get better flames. Find some way to activate the choke while driving. which will then dump more fuel into the engine, causing more flame

[@mrpartridge8765]

I tuned the carb on my moped to do that😂. You need a lean idle and a rich wide open throttle. You'll get some loud pops and flames without sparkplugs.

[@richgwozdz8580]

My Honda Navi does that with only an simple Vance and Hines exhaust with the baffle taken out and the carb rejetted

[@tannermartin7263]

If it has an over head valve you can adjust the valve clearance’s on the exhaust have it open slightly earlier or later

[@Randomscrap-92mx]

7:41 adhd moment

[@ainzowlgun_darklord7241]

The stickers make it an engine that increases its power ? this is crazy 😂

[@Harry_on_60_fps]

Nah those stickers tho💀💀💀💀💀💀

[@ainzowlgun_darklord7241]

@@Harry_on_60_fps Yes those stickers are something💀💀 Ngl

[@king-car-parking]

turn the air fuel screw on the carburetor somewhere close to the idle screw anb have fun 🔥💥

[@Smallenginesgalore]

I agree with @PorousShark7688 in the fact that if you could flip the choke on then that would give you flames. I just bought the same dual carbs as you have on that engine for my modified mower project. Also, there should be some adjustment in your air/fuel mixture on your carburetors. If you richen up your mixture, you will have big flames all of the time (although it will run like garbage and foul out the plugs on your engine) as long as you give it a tiny bit of throttle. My only advice to you is that you should take note of your current adjustments on your carburetors and when you are done shooting flames, then put them back to how they were. The engine that you used in this video looks like the same one as what you swapped into the primer gray lawn mower that you had on the 70 mph mower challenge part two. It also looks like the same engine as what was in your mower that had the hood covered in stickers (now the honda 650 swapped mower) that you were drifting in town in the winter about 1 year ago. Do you just switch the parts between the mowers for the videos or are they all drivable at any time? Not a bad thing, but I was just curious. Thanks for a great video!

[@Retr_01]

I completely died when you lost your words and started beatboxing instea 😂

[@SkylarPolicastro]

for real though bro i was on the floor when he started beatboxing

[@FlixFlax2012]

Do you have any video of when you build the suspension?

[@sirharbi8727]

love your content, this is what youtube is ment to be, not junk edited and cut clips what everyone else posts

[@osielh420]

5:24 you need to adjust air/fuel screw usually these type of engines when you give it gas and let it settle back down they idle a little high for about 5 to 10 seconds then lower rpm that's why yours "is bogging" , try reving the engine and wait for the rpms to settle then tune the carb as needed

[@SidneyHousenOfficial]

i get backfires on my engine if you set the idle screw fully out so that your throttle valve fully closed after you release the throttle and then normally you get pops and bangs

[@LeToon1]

" In today's video we are going to learn how to bump start a lawnmower " 2 minutes later... " In today's video we are going to learn how to push a mower back home " Yep, you're right haha 🤣

[@the_lilsteve0079]

pence tu q'un turbo pourrai s'installer dessu ?

[@Redneck128]

7:41 😂😂😂😂

[@HunterWolf-q3t]

You are awesome man i love mower builds keep it up 🙂🙂🙂

[@EverythingsAProject420]

if u drill out the jetting on the carb youll throw some good flames

[@JacobE-23]

I like the vibes, and the work! Subbed

[@DingleDork-no7gn]

thats some big flames

[@YonyLeclair7]

Nice video man !! Love it

[@TxchPlays]

7:34 😂😂😂😂

[@colevenrapgaming7814]

To help with belt slip u can drill 1/8in holes in the sides of the pulley that’s what I did on my mud mower it helped alot

[@MrJET-zz7gs]

Plss show your motor it so freaking cool is it still for sale these days and if yes where Can i look it up

[@Officialminibikes]

Love your videos bro literally 💪🏿

[@vancemacd6315]

Impressive machine. I love string start. Wish they still sold stuff this way.

[@24kManzy]

Bros life is amazing

[@iacopotuttino5515]

Maybe if you hold a bit the throttle you can have bigger flames, in 4 stroke dirt bikes it works

[@lukemiarecki5024]

What lawn mower are you using

[@JohnnyPelser]

I Freakin love that design on that lawn mower engine 😂

[@probablysomeonesomewhere]

The best transmission to get for these is either a mst 206 or the better one is the peerless 920

[@joeydepalmer4457]

Would thinner wheels work better?

[@Fuzzypattyg]

By the way if you keep your foot on the throttle when you hit the kill switch it will shoot way bigger flames and be way more efficient because you're keeping the throttle blades open which is dumping way more fuel into the engine which is then getting which thing gets shot out the exhaust which gives you even bigger flames

[@TheBanana_123]

Farmers’ Supra😂😂😂

[@CarConnoisseur_SS]

The stickers tho💀

[@MisterdionneYT]

don't be suspicious don't be suspicious !!!!!!!

[@CarConnoisseur_SS]

@@MisterdionneYT im not bro i just happened to notice, they look cool bro🥺

[@OliiverLUL]

+ 30 HP

[@MisterdionneYT]

@@OliiverLUL no cap !

[@RGVLambo]

could this also work on a 50CC derbi bike?

[@jeffarp7409]

I think that you may have your spark plugs mounted a little to deep down in your exhaust tubes. Put them almost at the end of the tubes. That way the unburned fuel gets to mix with fresh oxygen and it will burn better.

[@mihkus]

I put mine right after the exaust port, added some random weedeater coil and it fires after the power stroke, bangs loud and shoots out blue flames. I just turn the iginition off and go downhill last gear, muffler gets red hot

[@dominiquelavallee745]

Papir pantoute,continue à faire du contenu. 😂❤

[@procellfoxreal]

Those opposed twins are fucking indestructible torque monsters

[@notabadace239]

Its running lean at idle causing it to shoot more flames and engine braking is holding the rpm up to high for it to run lean

[@shaneanderson3076]

You got the right idea but you have it backwards running lean is not enough fuel. What you mean is running rich when a engine is running rich it is not running efficiently hence causing flames

[@notabadace239]

@@shaneanderson3076 running a engine lean can cause it to lean pop/ misfire running it rich usually makes for more pops on decel/under load but running a hotter plug and running a bit richer would make a great show under load

[@Scooter4690.]

The thing where it bugs if it’s been at idle for too long is because the idle jet is too big😊

[@Potchitadenji]

What is on that engine

[@richardspraggett1154]

All you have to do to make it pro frames high flames is set the carburetor to be more rich mixture of gas

[@richardspraggett1154]

You do not need a turbo you just need to mix the gas ritual in the carburetor by your screw

[@reesemolloy6109]

Are you still going to put that Honda V4 in a mower? I saw it on your TikTok

[@MisterdionneYT]

no the engine is trashed up it was seized ! there was alot of rust inside the engine

[@Diesr]

the bogging is due to too much idle fuel its stagnating somewhere in a bend or sum so it sucks too much fuel on idle or complete opposite no fuel at idle

[@rocketsnhotrods9022]

I've always had the same idea to put a flame thrower on a mini bike now I know what to do

[@david2005dk]

Bro need to make a cop killer lawnmower

[@Jenssss367]

what lawn mower body is it

[@yatiiie]

can you make a tutorial on a gas pedal? i am having trouble making one

[@98chevys10ls]

Take a bike brake handle with the cable and hook the end of the cable to the throttle, then weld the brake handle onto your footeest, but adjust it before you weld so you can reach it

[@antino4891]

How did you make the variable speed mower not blow a belt every 100 ft ?

[@MisterdionneYT]

make one of your belts is probably to short so it stretches to much and snaps

[@antino4891]

@@MisterdionneYT The one from the back is the one blowing up every time. But if I get a longer one it will have friction with itself and burn because of the tensionner. What should I do ?

[@2GK-MOTO]

I just found your videos and I’m surprised because they’re awesome….. where are you from?

[@faxbest1336]

7:38 LOL

[@lowkeydiegoduran4724]

You have to kill the engine spark and full throttle the gas to get the flames you want :)

[@jenklefritz6583]

I bet if you adjust the air/fuel ratio rich, put a bigger main jet, and adjust the slide more rich, you could probably have some huge flames lol

[@robot797]

give the exhaust a venturie air intake and it will fire always!!!

[@Nelly-ku4zn]

What mower is that pls I’m gonna put a 100cc engine in it it’s going to be my Daly driver

[@AnjaThomsen-q4x]

can i still buy the motor

[@Duck_man_yt]

"the engine produces unused gas." -MisterDionne but what you need to make better flames is to put the spark plugs down farther so the gas can ignite easier and it ill make it not only look better but sound better

[@onskuponsku_11eo21]

You are the best youtuber ever

[@lowkeydiegoduran4724]

What transmission is that?

[@MisterdionneYT]

pearless 6 speeds

[@joecompton8142]

3:50 WHOOHOoŒ

[@loicdrouin5466]

Ah et aussi c’est quoi la transmission sur le tracteur dans la vidéo c’est tu avec des poulies ou des gears

[@picopharade1272]

3:35 maudit beau son ça

[@bonqauevieswandra932]

You should try to build a rear engine riding mower

[@JeanAndréDuPreez]

You should maybe try amd do some fuel injection conversion

[@masonbmx7444]

Can I buy it?

[@ArminHaroon]

were you driving on 10th line

[@Noobplayzyt]

why you put the gas pedal on the wrong side

[@Gavinadcock-q2z]

The clutch is on the right

[@Noobplayzyt]

@@Gavinadcock-q2z i could never drive like that haha

[@Gavinadcock-q2z]

@@Noobplayzyt I probably couldn't either but a good amount of mower pedals are on the right

[@furiousrage4752]

C serait drôle que tu mettes un petit turbo

[@Go-Maddog-Bass-Boost-fan]

get some dragons breath and put it on the exhaust tip it will have clouded flames

[@nathanking8915]

Replace flywheel with aluminum or it'll splode. Common issue with those

[@MisterdionneYT]

where can i find parts for these engines tho ?

[@Donavin0]

you have to make it run richer

[@TrevMonsterbeastgame801]

damn flames on the lawnmower

[@spudstudios3342]

nice, you need to do some work to that crankshaft tho, poor thing is abliterated lol

[@MisterdionneYT]

yeah it is abliterated hahaha

[@HungryHemi48]

Turbo on that bad boy would be sick

[@michaelmeux4137]

Someone beat me to it but definitely put a little turbo on it.

[@BrysonWatson-j6h]

Bro needs a egt gauge now 😭

[@alpi.720]

Salut j'ai une question pourquoi tu parles anglais dans tes vidéos si tu es français ?

[@Cam-i]

Now you just need a bug catcher and supercharger

[@joeydepalmer4457]

Unless you are in a welding contest, WHO CARES if you are a bad welder! I am a bad speller but at least my math is gooder

[@carmelazenner8288]

Your gas and break pedal are reversed compared to the pedals in idaho

[@jwoody8815]

Kickass.

[@DEMO145]

I HAVE IDEA. Put motorcycle chain on lawn mower of no slipping

[@FaRnorThCrew]

Put the two exhaust together

[@amongust69]

w vid

[@rockfordian23]

Open the throttle when you hit the kill switch.

[@0vixie0]

PLZ DO MORE

[@Dirt-Tomfoolery]

If you like the sound get a harly

[@shadxwed_]

Bro spoke Russian for a moment 😂

[@jacksonpayne9917]

Chefs kiss

[@jamescraft5300]

thats cool bro

[@cameronschrade1448]

I need a modified mower again..😢

[@fever_dreams4773]

When are you gonna put a motercycle engine in a lawn mower? 😅

[@SatanicViking97]

Would be cool but definitely more fun to try to make a slow motor fast imo lol

[@joeydepalmer4457]

This guy MMMMUUUUUSSSSSTTTTTTTTT be from Alberta (with a BC attitude!)

[@carmelazenner8288]

Bro got an after burner

[@The_garage-f6m]

You should turbo your lawn mower

[@muddycruddymess]

you kinda just threw the secound coil on there, for example its not timed so it might be sparking on intake witch could make less flame then if you had it timed for exaughst stroke

[@muddycruddymess]

what i would recommend to do is take the plugs out and check what stroke the engine is on when the magnet touches the coil

[@jameydetter8629]

Dude, you should buy my turbo. Craftsman thing will go about 100 mph.

[@lukethornton5156]

You make some funny stuff

[@Justin_fourtrax3004x4]

Conect tes deu sparkplug a ta betterie pi mes une switch quen tla mes onn sa va tjr faire du feu so sa ba faire des flame pi tchen les au fon ferme le moteur pi ouvre les 👌🏽