We Bought the Cheapest 10HP Diesel on Temu and Put it On a Go Kart (it Rips!!)

[@CarsandCameras]

Go to partners.connecteam.com/carsandcameras to make the most of your business today! Brought to you by Connecteam.

[@RockenTravis]

Now to get a cheap temu turbo for ir

[@dbomber69]

It needs bigger rear tires. Diesel has the torque needed to rotate a larger wheel.

[@axialpad99]

@@dbomber69 Agreed, they could get more speed out of that thing for sure

[@jasonkaelin2337]

Sorry if I missed some episodes but what happened to Charles??

[@bodine2537]

@@jasonkaelin2337he’s still there every once in a while but not every episode anymore right now, think he had to move back closer to his parents for a new job an it’s too far to drive back an make episodes every week , haven’t seen him in bout a month or so though as of right now but he left the every week show about 6 months ago

[@jde88de]

The reason it finally ran is because you cracked the line open, its extremely hard for single cylinder diesel engines to bleed themselves.

[@dozer8065]

agreed, and maybe the fuel that was in it was a type of "shipping" super low quality just used to lubricate for shipping purposes, draining the fuel, changing fuel, and popping that line got all the good fuel in and bled the system.

[@StroDshiesty1]

@@dozer8065exactly i feel like it was oil to keep it from rusting during storage/shipping

[@cs-gj3yf]

@@StroDshiesty1 theres nothing to rust, especially the injection pump parts its all extremely high grade stainless, almost indestructible, its just lube for the tight tolerance stuff, keep in mind the plungers inside that pump have tolerances that are less than a thousanths of a inch

[@masjuggalo]

But I assume they mostly bleed like old mechanical injected truck diesels (pickup trucks) like when someone runs their 12 valve out of fuel just there's only one cylinder so there's no hope of one of six getting some fuel and making the engine spin over on its own

[@masjuggalo]

​@@dozer8065to be fair, diesel fuel is probably the lowest quality stuff you really can get for an engine designed to run on peanut oil

[@singlecproductions9653]

Ive had 4 of those. Remove some of the shims between the little injection pump and the block. It'll give it a few more hp and more smoke.

[@Failure_Is_An_Option]

For zero benefit.

[@proxyhx2075]

​@@Failure_Is_An_Option Are you literate?

[@davidanderson7720]

@@Failure_Is_An_Optiondiesels work different than gas engines. More fuel=more power😂

[@juliogonzo2718]

​@@proxyhx2075it'll blow up if you mess with the timing too much, and definitely will shorten it's life running it advanced more than stock

[@killzone9810]

Are you stupid?!​@@Failure_Is_An_Option

[@johnathantaylor2059]

“This thing is junk…..HEY WE HAVEN’T EVEN HEARD IT START YET…….Exactly” 😂😂❤ love you guys

[@polishcynic]

The moment you put a turbo to this gokart its gonna be everyones east european dream gokart, just imagine "The TDI Gokart" lmao. 😂🙌

[@WyFoster]

It's going to happen. Parts are on the way

[@Basedforlyfe]

😂

[@felikswielkopolan4001]

prawda!

[@fabriziogamer0863]

hahhaah fax

[@JamesD1776-uc]

Lol it needs a little tractor exhaust flapper

[@ghomerhust]

THIS

[@IndianaDipper194]

PLEASEEE 🤣🤣

[@christianfolkner]

like the first one!

[@qoph1988]

Incredibly important. I wish I had a diesel dirt bike with the exhaust flapper thingy

[@wewya.]

or make a mock big rig exhaust

[@twocvbloke]

When it comes to diesel engines, it ain't the horses, it's the torque that sends it, even with that swiss cheese flywheel... :P

[@grannysgushinggash]

yes there's no horses in a diesel engine it contains pistons

[@jacobkennedy6820]

@@grannysgushinggash i dont think you could even fit an entire horse in an engine.

[@sabero5668]

@@jacobkennedy6820 Then you don't have a big enough engine. Or a small enough horse I guess

[@bustinnucks1299]

Torque In motion is horsepower. What your feeling is horsepower being made sooner.

[@grannysgushinggash]

@@jacobkennedy6820 you can if you mince it first

[@jdogdiesel7242]

Now, For Some Free Mods!!! - advance injector timing a few degrees by removing 1 or 2 shims under the unit pump , turn fuel up also easy since its just an adjustment no parts swap, an ditch that stock air filter for somthing bigger and more free flowing that I'm sure you have layin around the shop, Then Bam MOARRRR POWAHH!!! And yes Turbo would be a good addition , makes it easier since that engine has a pressurized oiling system too

[@DarkAttack14]

Turning up fuel without adding air is a bad plan... EGTs up for minimal power increase. Advancing the timing would be a good plan though.. He already has smoke so more fuel is not going to do much

[@servicetrucker5564]

@@DarkAttack14 High EGTs on a NA diesel aren’t a problem. The old trucks with 200 hp had flames coming out the stacks and manifolds glowing

[@TestECull]

@@DarkAttack14 Being able to easily turn up the fuel like that is going to be the difference between the turbo simply cleaning the exhaust up and the turbo actually making the engine more powerful. If they want any gains from the turbo they need to be able to turn the fuel up. As long as they don't mess with the governed speed setting it should wake up pretty good with some boost.

[@zocka64]

@@DarkAttack14 On an NA diesel its tested to get more Power at Rich Mixture(even under Lambda 1/aka really smokey), since you are air limited, EGTs also arent a Problem und NA conditions. Adding air through a turbo would be the best addition for the extra fuel tho

[@Failure_Is_An_Option]

Timing advance may be of a very slight advantage. Increased fuel... pissin in the wind. Air filter... pissin in the wind.

[@sagenbabin8786]

Bruh that got me so good I was like holy moly she booking it then at the bottom of the screen “She made me play the footage back at 2x speed to make it look fast”. Yall are so cute it warms my heart

[@ThirstyFoe00]

This build needs a custom homemade transmotion like a 3 speed trans "crawlin, crusin, racin". Yall could do it for sure 😂🤟

[@zAvAvAz]

Yeah imagine an even gear spread for 90 mph!

[@sabero5668]

@@zAvAvAz With a turbo, more fuel and proper gearing for it, maybe it could get there. More importantly, would you want to ride that cart at 90mph? Answering "yes" could win you the "Biggest Balls Of 2024" award.

[@marco3392]

@@sabero5668more likely a Darwin award lmao

[@DannyNeal-g8y]

Diesels are all about the torque. The weight holds you into the curve, and the torque pulls you out. I concur; probably not a great track machine, but perfect for that Grand Prix woods course!

[@WyFoster]

Love how my starter box can start a 420cc diesel but struggles with a small block Tillotson methanol engine 😂

[@z1berzerker]

Its fighting the spark advance, not the compression 🤔😉... Tilly Meth builds are Bad A55 🎉🎉

[@RobertJeffersonBased]

@@z1berzerker Electronic ignition would be a great upgrades for a lot of minibikes

[@justinarseneau4450]

Whats the difference ? Arent they already electric ignition?​@@RobertJeffersonBased

[@marzsit9833]

@@justinarseneau4450 the difference is that spark timing on a small engine with a magneto is fixed, with no advance or retard possible while the engine is running. a battery powered coil ignition system can have adjustable advance, just like car engines have.

[@justinarseneau4450]

@@marzsit9833 oh ok thanks for the info

[@ROFLCOPTERS92]

I have this same engine I cobbled on to an ariens 28 inch snow blower frame. The power output is super good. I've put it in to foot deep wet heavy slush and it loved it. It was barely even taking a load and it was LAUNCHING that stuff.

[@MultiKelly85]

Your girl did awesome! Re watch the video and watch how she relaxed her brake foot. She had it flat out on the gas pedal. Glad to see you two enjoy go karts. Next she has to help build her own.

[@isaks3243]

pipe welder here. and I'm that sort of person who walk around and wherever I come across welds do I feel the welds just to know if the guy who made the things knew what he were doing and I can honestly say that a lot of stuff that is actually being used looks worse than your weld on that exhaust. I personally would suggest going down in amps because of how thin that matereal is. a rule of thumb is 25-30 amp per millimeter of wall thickness. the tricky part comes when you have two pieces of vastly different thickness. in that case did you do the right thing by starting at the flange and moving up to the pipe. you can also run 2T (wich means that you will have to hold the button pressed throughout the weld) and have a bit of slope down on the machine. some slope down means that you can release the button, have the amps go down over time and then hit the button again to bring the amps back up. it is a way of controlling heat wich can be really usefull in challenging welds. I would peronally rate that weld a 4/10, but when adding the handicap of being a complete newbie when it comes to welding will that bump up the score to an 8/10

[@geetar82]

Yall need to have a hot lap day where you re-run all the board leaders!! That would be an awesome episode!!! Cheers guys and love the vids!!!

[@bvick420]

the small hex plug on the bottom right of the side cover is an oil feed. the exhaust flange is close enough to a predator 420 that an off the shelf flange fits. i turboed mine with a vz21.

[@K-Rivs]

Where'd you buy the motor from?

[@jasonbirch1182]

Also, dont piss all your money away on brake clean. Buy a gallon of acetone for 20$. Get a squirt bottle and blast it off with compressed air. 8-11 cans of brake clean in a gallon.

[@WyFoster]

And it's the same stuff lol

[@michaelince910]

Thanks for the information!

[@idiotburns]

yes

[@TacticalHardlinePro]

BE VERY CAREFUL when using acetone, it will eat almost every plastic (including wire looms and most wire shielding) it touches, and cause many-a-headache if it touches anything your weren't planning on it touching or dripping on to.

[@TacticalHardlinePro]

@@WyFoster DEFINITELY not the same stuff

[@patrickbennett9120]

I was a TIG welder for 3 years... it is so much better than MIG... it just takes some reps to learn how much heat to use and building muscle memory with adding the rod... and you can weld any material with TIG. I was primarily an aluminum welder and TIG is the way to go... anyway enjoy... in a few months you will have the hang of it.

[@ExtraFungus]

Pin this please! Blue locktite comes in a tube/glue stick/paste. If you have any little ones, glove them up and have them apply it to all the bolts in the kit. If you don't have little ones, the paste still makes it easy and less messy. I haven't built one of these carts but harbor freight trailers are built with nuts and bolts, that's exactly what I did with my son, we poured outs all the hardware, put blue locktite on it and sorted them, it was a great first step in the project and it's a good first "wrenching" project with my son.

[@BlindDude]

59:02 i opened up 3 Arizona ice tea cans to make little alcohol stoves. They all had a syrupy sludge in the bottoms.. Haven't bought another since.

[@extremecheddarswityomom]

She dont need to be shy, we are here to support and enjoy go carts, mini bikes etc. Its issac we're here to judge and talk about... Them sideburnz... Lol Love em. 😄

[@ColinIrwin-g2v]

And let not get started on his poocha shell necklace,

[@EdStonesy]

These long form videos are impeccable 👌 I love having you dude on in my workshop. Great job on the diesel boys!

[@drgti16v]

John going to his roots with the music during the painting montage.

[@danw1955]

That's hilarious!! Reminds me of those Thai racing rice tractors! Those maniacs spin those things to 5 or 6000 rpm's off the line, and I fully expect to see a catastrophic flywheel explosion at some point.💀 Despite the initial starting issues, I think it's going to work out well! It would be fun to see it on a modded mini-bike frame with a turbo and an actual transmission, so you could get the most out of the limited rpm range.😉👍👍

[@lensrc7460]

Ya'll need a set of holes on that bench to bolt down engines. Tapped so no reaching your hand under the table.

[@drinkmorecocacola]

A “universal” plate to mount on would be a cool upgrade to the shop. I LOVE upgrade videos

[@dickkallerhan2412]

one would be a start 😆

[@alexmikhael5061]

I was thinkin a c clamp kinda thing with X pattern for the 4 bolts, and the clamp fastns down on the ''table'' or into a vise even but ''designed'' to set into the jig table thingie and watnot ;)

[@freedomisntfree_44]

Good idea 🤙

[@RueKake]

Temu.. Giving the Chinese continuous American comedy since 2022

[@ClintonRyanThompson]

So happy to see home much you guys have grown the channel over the years!! Keep up the great work!

[@EdStonesy]

Can’t believe you got the original Goose from top gun to help out

[@keystoneangler3217]

Lol. I have that same motor on a mini bike. With 40 converter. I call it the D-69 cat lol. It's all done up to look like a cat machine.

[@bicbuilds]

i need to see this

[@humpday2267]

We wanna see this sounds like a cool build man

[@xxbambamxx7261]

I've heard some of these engines have sat in a dirt turner for over 6 years, with little to non maintenance at all, still starts and runs like a champ

[@CarsandCameras]

Now this is a sweet platform!

[@Jockymcbock]

Was just looking at some diesel engines! Excited!

[@mathieulachance151]

Absolutely!!

[@mathieulachance151]

It reminds me of the small diesel powered go kart you guys built a while ago with the engine from EBay !! Loved that video

[@DuDieselDude]

@@mathieulachance151lol they said that in the video

[@wyattflanders8459]

Now it’s time to super or turbo charge it

[@myneckjusbroke3301]

with tig welding torch angle is fine unless you are welding aluminum then you would 100% need it close to 90. you'll love it prep is key with tig welding you need shiny metal. you can also use brazing wire with tig to make beautiful gold welds. its funny too i just bought that consumable set.

[@bigbird6788]

Love the long form videos! We asked, you delivered thanks from all of us detail orientated fans

[@goosenotmaverick1156]

I have a hard time finding enough time to sit down and watch an entire movie though. Personally I liked the 30 ish minute range, longer than 15-20, but not nearing feature film length

[@tihzho]

I didn't know Will Ferrell built go-carts! Go Ricky Bobby! "If you're not first you're last"!

[@jvsyoutube3298]

yeah, good to get a tig! you guys need one, and when you are good at it you can take the tig home and do welding at the tv room table. So much less dramatic with splatter and stuff then a mig!

[@sammcbride2464]

One last thing...I have a KLX140 and I think it is rated at something like 7hp. After my big bore kit to 190cc and a port, carb, and pipe it has over 15hp. The thing is a beast and the motor is still air cooled.

[@derbydriver7431]

I almost feel like I'm watching an episode of Diesel Creek....lol

[@aronfaine9457]

Matt would be stoked to see this lmao

[@danielsteward5090]

I love it! I was thinking that the Diesel would be slower than the gas engine, but I'm surprised like you guys were. Tig welding is like Brazing, but with lightning. That Tig welder will shock and burn the crap out of you. (Tig is my specialty),sweat and bad ground connections will teach you about electricity quickly. Be careful how you hang that torch when you are between welds. It will be hot enough to vaporize your shirt sleeve and turn the skin under it to "well done" in a second. I saw you almost brand your belly with that torch the first time you lit it up. Boro-silicate cups stay hot about 30-40 seconds after they stop glowing. Good luck and Practice makes perfect. Get an extra tank of straight Argon for Tig welding Stainless and Aluminum.👍

[@MikeSmith-bb5ii]

Worst tig weld is the one you didnt try. I was blessed to have my entire apprenticeship in tig doing stainless food and beverage equipment 29 years ago. MIG = Monkey Ignorant Gun. Any monkey can do it, and some do it well, but tig is an art.

[@bigpipol]

amen ma man

[@derrickmanning2597]

Over here in UK us stick welders call migs hot glue guns! I've done thin sheet and even motorcycle headers with stick,done heavy work too (RSJ'S)and cast iron! most of that is an art as well!

[@jamesoverstreet35]

Guy's the Diesel go-cart is an Awesome build & i Look forward to you guys adding a Turbo to the build !!! I Really think it would be an Amazing project because it would open up possibilities for folks like myself as I have several diesel small engines that I have acquired from auctions & trades over the past few years !! I build go cart's, buggy's, Side by sides etc..... & have been looking for a Tried/Tested & True setup for a Turbo Diesel small engine combo that's solid & not a "Break the Bank" investment !!!!! I Simply LOVE your Videos & how you guy's are able to include all of the content that makes my builds so much Easier as well as much more inexpensive !! PLEASE keep the builds coming as I watch Every Video you guys post atleast a half dozen times per video as a reference or to introduce friends & Family to your informative & just Downright Wholesome HILLARIOUS "Spot On" Builds !!!! Love you Guy's!!

[@Creed9230]

No one talking about how the Diesel engine sounds like a lions roar when he lets off the gas at 1:10:48 Love the sound lol

[@jasonbirch1182]

Go watch robot cantina to get alot of good diesel engine theory and tuning tips. If you turbo it run a chamber on the exhaust after a bit of regular sized pipe before the turbo to help with the single cylinder pulse. First thing first is an EGT gauge.

[@T3NNESSEE]

Id say going 1-2 teeth bigger on the clutch would improve the top speed by a lot. 1 tooth on the clutch makes up for 8 teeth on the rear. A Turbo and a good porting job would improve the hp and torque by alot.

[@aidanlyons1155]

how many teeth on that clutch sprocket, did you manage to see by chance?

[@T3NNESSEE]

@@aidanlyons1155 Just taking a guess id say 14-15 if its a 1 inch shaft engine.

[@therealracer135]

I mean, they did say it's already sketchy enough in the corners, adding speed probably isn't going to help much, at least not on their track.

[@lifehealth489]

@@aidanlyons1155 bobby dont miss anything

[@richardsteele6776]

The mix of colors reminds me of the Partridge Family bus from the 70s. Need a flipper on the exhaust pipe. John it was nice of you to introduce your girlfriend. You two make a great couple.

[@throwawaypt2throwawaypt2-xp8nx]

I skipped that part

[@ur_quainmaster7901]

Before things get crazy with mods, I'd love to see a little torch shooting propane into the intake via "nitrous" button.

[@WyFoster]

You're speaking my language brother

[@lamarzimmermanmennonitefar5269]

That would actually help.

[@gorillaau]

​@@lamarzimmermanmennonitefar5269It's not goimg to hurt anything of value.

[@cs-gj3yf]

nobody uses propane for a reason, nitrous is better.

[@jasonbirch1182]

​@@cs-gj3yfwrong. Nitrous is extra air, propane is fuel. A diesel makes power with timed fuel injection and the correct amount of air. If it's making black smoke then you need more are, if it's not you need more fuel. Adding nitrous to a diesel making no black smoke is going to get you little/nothing. Adding propane is untimed fuel for when you can't get any more from the injection pump. It helps spool the turbo earlier too. I have a propane Injection system I built on my diesel Mercedes I tow with.

[@LittleSweed]

We have Moped cars here in Sweden as 15yo that has 2cylinder ~500cc diesel engines between 5-8hp stock a cvt and they are regulated to go a maximum of 45kmh ~28mph, the cool thing is that you can change weights in the cvt and change out the exhaust and the stock dci/hdi box and you will have 15-25hp and now these small moped cars are good for 80-100kmh ~50-60mph which is rather fast when you take in consideration that it is a moped that by EU law are only allowed to go ~28mph. So it's fun seeing you guys trying out diesels they might not have the fastest acceleration but you can usually get them to stupid fast because of the high torque diesels naturally have 😁

[@bentleeohlsen4542]

i would love to see you put a turbo or even a supercharger on this machine

[@sawyerbennett8227]

I was cracking up at around 1:12:30. John looked like he was on another planet or something 🤣

[@koaasst]

tell ya what, this was in my feed, and it was right up my alley. great content, great shop, great personalities. makes me wish i had friends lol! well ones that were into this kinda fun. see ya on future videos ill be watching.

[@WyFoster]

Rolling coal patrol!! 🔥 💨

[@WilseyIII]

Ive had a few generators with this same yanmar l100 "clone" ive started with a cordless drill, not impact, and i do this with the latest one i have with a sterter... Hold the compression release down until you have the rpms all the way up with starter/ drill and let it go. The momentum of that heavy flywheel will do the rest!

[@Alkatross]

Ah, you fell for the ol' flywheel scam. Happens to the best of us.

[@bwood282]

I bought this same engine for my snow blower and it works really good. I dealt with some small issues finding the right belt size but once I got that dialed in it’s strong as a bull!

[@g0ldensample21]

Your buddy needs to be part of the channel. He's already super comfortable with the camera 🙂

[@bicbuilds]

He has his own channel thats why hes so comfortable lol

[@g0ldensample21]

@@bicbuilds 🤣👍. I did not know that. I'll have to go check him out. What's his channel name?

[@jumpercabledadz]

@@g0ldensample21JumperCableDadz

[@crossrain1188]

You guys have so many shifter Karts and go karts I would love to be in the same place as you guys in a few years from now. Also this video gives me old cars and cameras vibes I love it ♥. Keep it up

[@unidude-lx3kp]

I apsolutly died of laughter when I saw the comment about doubling her playback speed

[@nihildegrasse1700]

Uh, did they know about depressure knob?(the little red knob thingy, top of the cylinder head, beside the injector. No wonder the starter are just shredded to pieces 😂😂😂

[@lensrc7460]

yes, they knew about it

[@nihildegrasse1700]

@@lensrc7460 I think they should use the knob to disable the compression, thus make it easier to gain more rotation momentum. After enough momentum gained, just let go of the knob and the engine will do the rest. That's how we start some Chinese diesel engine here. Those Chinese really go low with that starter tho.

[@lensrc7460]

@@nihildegrasse1700 They were. Watch again. They even talked about it.

[@GuitarRek_Films]

@@nihildegrasse1700they did the starter was just that shitty that it still broke

[@greenwizard2000]

I love TIG welding... can be so satisfying once the learning curve realy hits

[@waxore1142]

diesel has a forever shelf life

[@juliogonzo2718]

They've mandated summer fuel where I am to be B5 biodiesel now. It's more prone to bacterial growth imo. My old job had a truck sit for about a year and the fuel went bad. Another truck sat for 3 years and it didn't because it was before they put that crap in the fuel.

[@waxore1142]

@@juliogonzo2718 you can drain it and run it through a hard filter and remove just about anything

[@DeltaOGaming]

@@juliogonzo2718biodiesel is sh**

[@chucksmalfus9623]

Drove 18 wheelers in the 70s when fuel was like 30cents a gallon, always had to put an additive in it to keep the groth down or it would turn like jelly.

[@waxore1142]

@@chucksmalfus9623 i have seen 30 year old diesel fire up. only time i have ever seen diesel turn into jelly is when its too cold.

[@patrickrobinson2520]

I think Blackstar really hit the nail on the head with the fly 3 series amplifier. ( I have the combo extension cabinet (fly103). After using my 6 Watt setup for 5 yrs. This is to be delivered to my door by Saturday. I'm very excited and proud to make it my new practice amp(5 watt mode!!) I'm 46 and this amp is for way more than beginners.

[@paulforrester4057]

Loads of torque I bet

[@nizamaamer]

Let’s all appreciate the hard work that goes into making these videos!

[@johnbchambers1442]

Ya know, your other diesel from YEARS ago came with a broken flywheel as well! Had a single fin broken off!

[@harrywagner3877]

New cart, no long pants, no long sleeves, no gloves. You guys are nuts ! 😲 Nice video. The diesel gives you a ton of torque.

[@ne634]

Wheres Charles? Ima ask this on every video until I get a answer.lol

[@CLPRPSD]

Search “ Did Charles from Cars and cameras leave”. I believe there is a video of a podcast with announcement?

[@scubasteve3293]

I'm doing the same thing. I feel like there was a fall out.

[@CLPRPSD]

@@scubasteve3293 it seems that it’s time for change. Hoonigan iis now crap after it imploded due to corporate nonsense, Donut media has everyone jumping ship, Grindhard Plumbing lost a guy and now this. Change happens, sometimes it’s for the best, but not always

[@scubasteve3293]

There is i just found it, I'm glad he left on a good note, I'm going to miss that guy.

[@ne634]

Yep I found it.. didn't know they have a podcast

[@rocxylemmon8535]

I love the beginning weld teach, you all are good people all togeather, i loved how you all taught him how to weld and beginning skills... this youtube is awesome 👌

[@snowcow1173]

Just wanna mention this video was so good i didnt notice it was longer than an hour. Been watching since 6 pm and now its 12 (was doing stuff in-between but never changed videos)

[@jessevance8455]

Hey @CarandCameras. Just stumbled upon your channel. (Probably because I have wanted a go kart my entire life and often mention it). Like it’s definitely a bucket list item. It may be too late for me to tho? I went through a heartbreaking breakup where my ex is trying to keep our kids from me. You see, I worked too much she got bored and cheated and cheated and… you know cheated. Wow SMH. Anyway I got set back. The whole thing has nearly destroyed me mentally. But I don’t want to feel physically paralyzed today. This is where I want to thank you guys for putting together a great show. It was a needed distraction for me. I even feel more motivated. I might do something productive today. SMH…. That’s Wild.. just a few guys having fun building go karts but the unknown impact elsewhere is saving life’s. Again thank you guys! Best Regards Jesse Vance.

[@isaacitllbefine7231]

Sorry your going through some bad times. Its never too late to get into karting. Next month I'll be 48

[@ToolinAround]

BBR really went over the top with that kit! Impressive!! You guys are awesome for building their kit on your channel

[@salty6pence672]

Wow got out of the game a few years back, Came back to see what's new and you guys are still rocking videos! AWESOME

[@AtelierulDinGaraj]

Even on summer days, put with a syringe some oil 2-3 ml after take off that orange cap from top op cylinder, help piston to lubrificate, on winter days it's a must, have joy

[@ZippoVarga]

Quin(n) is adorable!! That little bit of shy I'm sure is not a reflection of her true personality. Looking forward to the day when she's confident enough to rip the Drag Rail down the track!

[@jiefflerenard1228]

Actually the center part of the pull start is the drum of a basic no recoil rope pull start.The 2 little grooves in the ridge in where the knot at the end of the rope fits. Good luck

[@dennisnorth1250]

Another great vid guys...Guess the torque of a diesel and weight over the drive wheels = Traction could be a factor...just plain ol brute force....love it

[@KetansaCreatesArt]

Well done. Amazing colour work. The slowmou uncle was faster on the bigger diesel engine because his weight counterbalanced and grounded the wheels. A suggestion - Must attach the original muffler to the extended tube. 😎✨

[@MM1Anderson]

That thing has so much torque. Bigger back tires for more contact on the loose stuff and more cushion in the rear with all that weight.

[@arthursmith5409]

Both of you was extremely excited, we were too! Look, different gearing for a faster top speed and a small turbo addition, it'll spin up faster with a little power braking at start to build boost, then let it rip on a hot lap....

[@locutz]

Ive never watched an hr long youtube video beforee this was quite entertaining,learned alot too .

[@bryduhbikeguy]

Fun stuff guys. Congrats to BBR for the design.

[@diggerdagger1345]

Cars and Cameras, love the video and the note about safety. I want to add one further safety note for people. If someone who is going to ride a go kart with long hair.. please tuck it up or tie it up. It can get caught in the rotating parts exposed on the engine. And that can cause serious injuries... be safe out there!!

[@jonathanshiflett8877]

I’ve got a little monster moto mini bike that I threw a 98cc on, I closed the spark plug gap some, moved the ignition coil closer to the flywheel, deleted the governor on the engine, threw on a cheap carb and header pipe from Amazon and it RIPS I can hit about 40mph on it before it vibrates the hell out of the bike and so I slow down and it cruises at 30mph no problem, my only complaint is the camshaft is made entirely out of plastic but if I had to guess it’s making around 4.5-5hp now and it’s hilariously fun

[@VintageCR]

just to recap; diesel generator, mounted on a 'put-it-together' go-kart is awsome! and that's cutting it short still haha that thing is a monster!

[@averykompelien6616]

The diesel is really showing torque in this video. It has lots of get up and go but cuts out pretty quick. Cool video!

[@shortar15]

hey, Arizona, Southern Style Iced Tea is da stuff Black tea sugar filled at 99 cents back in the day was de stuff. ever see where it is made who owns it has nothing to do with Arizona nor the south, but taste is wonderful.

[@masongiles8443]

Hell yeah I wand to do a small diesel build some day maybe run it on black diesel 😊

[@MaLiXs88]

Diesel gate is a really good name for it 😂

[@MsLoneWolf4]

Years ago when i did paper delivery i found and bought a yard cart one wheel peeler and stopper, revived it and a 5+ horse briggs with a 1" shaft, it hated low speed and uphill, then engine decided it had enough. Though it would be cool to revive again with a rotary, then electricified like the genekart but trailered( till seeing the driving part) bue now maybe i should go with diesel. Then i wouldnt have to worry about lack of torque. But first thing is converting the axle

[@lenniesabas2202]

Here in the Philippines those cheap diesels power hand tractors that are pulling trailers filled to the brim with dirt, potatoes or rice bags like those lils boys can pull low how you enjoyed it in the end after hating on it half of the video ❤️

[@99milesaway41]

Man, that thing is surprisingly rowdy, can't wait to see it tuned and turbo'd!

[@sammymaldonado8168]

Yall need a video restoring all the old builds

[@fortssciencefortress1606]

So the fact that you have the cool wall, a la Top Gear, I’m all in!!!

[@juliogonzo2718]

You can adjust the injection timing by adding and removing shims on the injection pump. Put a clear plastic tube on the outlet of the pump and turn the engine over slowly with the "throttle" open till you see the fuel move in the tube. The timing marks are on the flywheel/block. It shouldnt smoke all the time you are probably over revving it. She gonna blow up if you keep doing that

[@jasonbirch1182]

Cameras definitely make me kinda weird sometimes too. Shes a super cutie. Love a natural down to earth girl. Nice work john.

[@adambater2767]

Like these guys they have a sense of nostalgia with their videos 💯👍🏻

[@Sausketo]

If you're gonna get in a bolt together cart, you should invest in nord lock washers to prevent vibrations loosening bolts

[@Tonyleanedbk]

Isaac is the man he makes this channel

[@overbuiltautomotive1299]

Guys to bad installing a CVT on that kit was not an easy to do thing due to room as its a must do i thought i never have and luck with slip clutches .who ever makes that kit need to add that in to lay out .. and i like re-greasing all chine roller bearings with moly grease or read n tacky lucas brand ...Great job

[@snakeplisken2123]

I made some of those plastic washers from some HDPE tape I had and I have some leather punches for the hole then I stick them in place and trim the outside to the shape of the part. It’s kind of an expensive rout but I had the stuff luring around. The adhesive back makes for easy install and if you have to take the thing apart there’s no extra washers to loose, keep track of, fumble around with etc.

[@AngelaWest-if5ko]

I never thought that there would ever be a diesel small engine but they’ve been around for YEARS! It’s crazy how far technology has come in just the last ten or twenty years.