How to Make Absolutely amazing car INVENTION

Saze i Use
21.5 x 4.2 cm
1) 60 cm
2)100 cm
3) 140 cm
4) 160 cm
Homemade KneeBlades Durable Rolling
• Homemade KneeBlades Du...
Know More Subscribe here:
/ drhacker-com
Instagram
/ dr_hacker87
Business or Cooperation
[e-mail]
Check my Other videos :
/ @diy.invented

[@izzydizzy1115]

I made a similar set from scraps I had left over from a construction project. Mine are taller and I put rubber pads on the very bottom board so they don't slip on concrete floor when driving up on them. Very stable and it was a fun project. I do like the idea of wheels to move them around. I'll probably add them to mine. Cheers!

[@josephatnip2398]

car ramps congratulations you're only about a hundred years behind

[@Naughty_Squad]

Funny or not but i have metal ramps and they scratch my bumper every time because the car is lowered this is not a bad optin and it definitely won't slide forward when you trying to get that heavy thing to crawl up.

[@dustincochran2700]

@@Naughty_Squad Easy solution for you. My car is also lowered and the parking platform on the ramps will not fit under my front end, it's higher than the bottom of the bumper. Determine the angle of your ramps, in my case it was 17 degrees. Measure how much length you need to prevent contact, 2 feet will probably suffice. Using a 2x6 (or 2x8 if your ramps are wide enough), cut the edge of the board corresponding to your ramp's angle. It should sit perfectly on the ramp with no gap. This extends the ramps and will lift your car 1.5" higher. If you need more, use 2 boards. Make this even better by counter sinking a couple bolts on each board that will drop through the existing holes on your ramps, essentially making keeper pins. RWD cars have a tendency to push the ramps on polished concrete. The bolts will prevent this. Works great.

[@Naughty_Squad]

@@dustincochran2700 i use couple of 2x4rs. That's why i liked this idea once you make it it will work for years..

[@jasonb4738]

@@Naughty_Squad so buy lowrider ramps. Mine hit the back wheels before the car is all the way on it. Its cheaper to buy ramps than buying the materials.

[@reubendobbs8011]

I think the romans used the same thing to change the oil on the chariots! Lol 😂

[@ArchGBUStanton]

Wow, took for ever but at least I got to hear Darth Vader breathing for awhile.

[@GrnXnham]

The thumbnail caught my eye when I noticed that these ramps are nearly identical to the ones I made myself about a year ago. About the only difference is that I haven't put castors on mine. I made my own SAFE ramps after my full size truck crushed my store-bought ramps despite the ramps supposedly being able to support the weight. No way solid wood is getting crushed. The only drawback is that they are heavy. And everyone here keeps making the comment.."Why not just go out and buy some ramps?" Answer..."Because they suck!"

[@rickykraus7450]

I made a set of ramps like this around 15 years ago. I didn’t have any low profile ramps and some left over 1x12’s.

[@jdilksjr]

@Ryan Hogan If you would drive past the end of these, you would also drive off the end of store bought ramps.

[@jasoncoleman6378]

I thought the video in the beginning, was a promo for the cordless dewalt miter saw 😄

[@charlesmaverick-im8nd]

Boa ideia! Forte, confiável, estável, simples! Muito bom! Parabéns!

[@joethrailkill1475]

I built a set of these in 1960. My patent royalties were lost in the mail.

[@marioalvarado3284]

Thanks so much for sharing your idea man, I appreciate it! Hello from SF California.

[@edromero6352]

Thanks for the refreshment I’m sure lot of people have never thought of this personal I think these are better the $30plus cheap ramps this are not going to fail

[@goodjah8946]

The most interesting about this upload was the "knee carts" since I never seen those before... Fun fact(that really says more about me than anything else), but I was seriously wondering how those small wheels where going to support the weight of the car! Haha! This since I really saw an application for the thing..like drive onto and then be able to ajust the cars position sideways which could be of use in a small garage/shop...now I just feel plain stupid;-)

[@thomasmarzigliano4870]

For the price and the weight of the wood, I'm happy with the polymer ramps I bought 15 years ago and they still work great

[@paulkanyoka9604]

I think that vertical board should be strong or reinforced so as to act as a stopper too.. Not everyone has the skill and technique to stop the car before it breaks that board

[@dancahill9122]

As far as not having the skill to stop............break the board and run of the end onto the frame a time or two and I guarontee the driver will learn, real quick like ! ! 😂😂😂😂😂😂😂😂😂😂😂😂

[@martybaker9765]

Or just spend 30 bucks on a set of light weight ramps.

[@charlesmcdowell3984]

@Mr Blimp and the 40 dollar pos you buy wont hold up as long as these. Lazy.

[@alexcastor7792]

Most of the ramps sold in stores are too steep - low-riding cars would scrape and damage the bottom of the front bumper. This self-made one can be made with any angle you want. Great idea!

[@DankDadReviews]

Ramps are actually cheaper then the lumber and hardware to make these.

[@barrellcooper6490]

@@alexcastor7792 I had problems with ramps and jacks not fitting under the air damn. I found low profile ramps that work. Just saying wasn't that hard to find low profile ramps.

[@kiyosenl.3889]

@@charlesmcdowell3984 as far as ive ever seen they do hold up a really long time, in fact plastic doesnt rot but wood does. The metal ones will rust i guess but it would likely take longer than it would for these to rot, so yeah. Not really worth the time to make these

[@robertheinkel6225]

I built a similar set of ramps about 30 years ago, but made mine with removable ramps. Much more versatile. Years later during Desert Storm, I had to change the nose gear tires on the KC-135 aircraft, without the proper nose gear jack. I built another set of ramps using 2 x12s, without the removable ramps. We towed the aircraft up on the ramps, then used the Main landing gear Jack on the nose gear. By putting the plane on ramps, it raised the nose tires enough to to get the MLG Jack between the tires. We ended up changing several tires using the ramps. When you have an aircraft weighing in at over 144,000 pounds, you do what you go to do to get the job done!

[@fartpooboxohyeah8611]

You made ramps with removable ramps? Huh?

[@VolkanTaninmis]

@@fartpooboxohyeah8611 nice point.

[@davee6161]

10:51 seconds that I'll never get back. My grandpa made a set of those back in the 40's that I still use. Seriously video could have been about 30 seconds long.

[@cesaralvarez5982]

The funny thing is you can buy these for a fraction of the cost of the wood, no labor, and already finished.

[@StupidEarthlings]

@@cesaralvarez5982 i came here to say the same thing. Thats KZbin, ya win some, ya lose some.. seem to be losing alot these days.

[@scottgaston742]

Amen brother

[@randybethune5854]

You watched for 10 minutes?

[@davee6161]

@@randybethune5854Shit, I'm busted.😅 Actually no, I fast forwarded thru most of it.

[@pedrovelez4742]

Excelente proyecto. Sencillo y seguro 👌

[@dangol6848]

Just mind blowing. Never been done before.

[@NuvoVision]

😂😂😂😂

[@carlosruano75]

😂😂🤣😂🤣😂😂

[@Sonic-sh2vh]

Yes one of the greatest engineering achievements of the modern age. It’s mind blowing that this concept has never been realized.

[@toobad9946]

@@Sonic-sh2vh Someone will just steal this idea and make some out of steel or plastic or something!

[@dancahill9122]

Except maybe 10 or 20,000 times.😊😊😊😊😊😊😊😊😊😊

[@Larry-Hi]

Great idea, make sure to block the rear wheels for safety.

[@iowaudioreviews]

Must be a city boy. We been doin this on farms in the midwest for 100 years.

[@kllgrogto5838]

Ramps to service chickens farm boy? Tractors and pickup trucks don't need ramps.

[@iowaudioreviews]

@@kllgrogto5838 Wow a beastiality joke about farmers, classic. Farmers have cars and vans as well.

[@dannyixoye262]

@@kllgrogto5838 Question, this may cause you to be butt hurt, but were you born ignorant of did you got to a liberal arts college and take classes...

[@kennethpayne9694]

wow that's amazing they are just like the ones i made 40 years ago

[@waynesmith9765]

So you invented these ramp in 2019. I've had a set just like them for over 30 years.

[@tomharner83]

Loose the swivel casters... Switch to straight casters... They'll be much less of a pain in the ass.

[@peaeye3467]

Those must be those new safety flip flops I’ve been hearing about. Perfect for carpentry work and pretty much any work with power tools. 😆

[@sisyphussapprentice8976]

There are some very brave bunnies out there.

[@robertawhitfield2414]

Great job 👍...Now add you some straps where you can pull & push your ramps 👍!!!

[@danielcarreras9554]

Genial !! Gran idea amigo saludos desde argentina

[@jimpie231]

Great idea, my Dad made some like yours, however, they were too heavy, as are yours. Over the years I bought 2 sets of metal ramps, and broke both sets, damaged the plastic parts on the car, etc. The ones I made are shorter and use 4x4’s and studs, they’re lighter and shorter. I’ve been using them for 25+ years! I use them for oil changes, inspections, and changing parts that will be easy to access! Jim

[@jimpie231]

Wooden ramps don’t break, and are very forgiving......

[@mistermikeanson]

Chock the rear wheels!!!!! Don't rely on the parking brake when you are underneath.

[@sleepinglioness5754]

Agree. This is very important.

[@dough9512]

@Matter Do Obvious.

[@kenallen512]

Replace the revolving wheels with fixed (non revolving) wheels, it will move forward much more easily.

[@jeffnarum1373]

Second that. They would go from push to pull way easier.

[@cherylmedeiros6287]

What6the purpose of the wheels? To move this contraption?

[@miroslavjuicebag]

I like the stepped design, I'm always a little nervous driving up my continuous incline ramps.

[@jaypreddy8185]

Amazing! I made a set just like this (no wheels) 25 years ago.

[@carlomezzatesta4659]

That idea has been around for 2.5 Thousand Years how do you think they built the pyramids and Stonehenge

[@jakee8704]

Used ta have ta make these ramps for our flatbed tow trucks 👍👍 Well done

[@rig_ekb]

А я брус 150*150 взял, сделал пропил и прикрутил в наклон доску, норм получилось

[@ron5935]

I built mine in 1972 and still use them today in 2020. Lets see 4 times per year x 2 cars = 8 x 50 years = 400 oil changes + other repairs. Strange things breaking on my cars is a problem that went away 50 years ago. My 2004 Buick has NEVER seen a garage. I share the ramps with my son now.

[@southernman5839]

My Dad made a set of ramps years ago. He sandwiched his together on the sides bolted with rods and nuts all counter sunk. He cut the slope you drive up on . Wood is heavier but there’s no danger of the wood collapsing under that weight. Nice job on your ramps!

[@sbenc]

Great idea, I need something like that, and have some timber at home for this. Thanks

[@curtisgeorge1566]

An engineering marvel.

[@ln5423]

Missing some back wheel block chocks. So the car doesn’t accidentally roll back and crush you.

[@brynjolfureinarsson6038]

That is how do it

[@the_Conor]

Доски у меня уже есть, осталось мерседес найти для моих досок.

[@my2centz196]

I have been planning on building the exact same thing for quite a while lol. It's kinda funny that this video popped up in my link even though I didn't research it. I have ramps but I need a longer more gradual raise because my vehicle is too low for factory ramps. I have the limber and all I just haven't needed them or had the time to piece together yet. The only difference that I had in mind was 1 small piece with 45 degree angle on both sides and the end side just a block with no angle. Personally I like my idea better but this would probably be a little easier should work as long as the end block isn't too high plus you might wanna be careful because it doesn't seem like it would make a good stop as the vehicle could just push it off. I suppose only a flat block or two laying down would give you a much better and safer stopping point and you could still use your coasters on another plank behind it which is actually quite a nice space saving idea I may inquire in mine provided I ever make it. I do have nice floor Jack's and stands but I feel much safer working under a vehicle that has all 4 wheels on the ground. Anyway nice video and quite clever.

[@chilidog73]

Those are amazing! Like the 8th wonder of the world!

[@criqdekuyper9259]

Bought a set of prefab ones for less than the cost of the wood and nails. Saved 10:51 too.

[@SuperGlen100]

Nice idea, although being as my workspace is limited, I have the metal type of ramps the nestle together

[@dekurvajo]

Nice invention! If you did not found a name yet i have a totally fresh idea: "ramp"

[@waynesmith9765]

But be careful that someone doesn't steal the idea and sell them at wall-mart as ramps.

[@vitamix2011]

Теперь еще лежак на роликах надо сделать, чтобы не корячится каждый раз, залезая под машину.

[@Twelvestar64]

I made almost the identical thing about 23 years ago. I used 2" × 12"

[@MarzNet256]

I like the big stop at the end of the ramps. You won't drive over them and possibly damage vehicle.

[@franciscopino7552]

Oh,yesss! Great stoppers, whats 900 kg for such a strong piece?

[@NAls-zm4fm]

Well done, great video and right to the point. Would you please share the length of the wood for each layer?

[@leonvdm]

Come on. A little imagination and brain and you can do that yourself.

[@stace5676]

And every chance you might get them evenly spaced unlike the ones in vid.

[@conway7812]

Wow great idea. To all the people adding negative comments I guess your dads didn’t shoot a video 40 years ago to let us dummies in on the secret. I’ve been pricing racing ramps for my low clearance mustang and every one wants a lot more than $40 bucks.

[@jakee8704]

Could always undo the vertical board and add a longer one the the bottom of the horizontals then re attach the vertical for that extra inch and half. 😁

[@meno_a7571]

Am I the only one whom wanted see what the little wheels would do? 🥊🤣

[@artnalex]

6:52

[@user-ck6vu5ix2j]

Всё гениальное просто 🙂👍

[@timhorton6485]

Well that was 11 minutes ill never get back.

[@angelocollins3372]

Yes me to but glad I am still here why do people come on here making something that cost more than just going buy it at store cheaper

[@miguelvalencia2528]

Well, 5 minutes for me, I watched at 2X speed.

[@angelocollins3372]

@Matter Do I am gonna see will building these Monday and see then I am always grown enough to I am wrong

[@donaldmoore6327]

Amazing !! how did you think of that .. so much easier than carving them from a block of stone ....

[@mikej6544]

Your head is a block of stone

[@eugens-1980]

8:55 Lord Vader 😂

[@wizeguy9004]

I feel like I wasted 10 minutes of my time

[@macman9689]

you probably waste more time a day doing unproductive dumb shit

[@jtauscher]

Next time try 1.5 speed 😅

[@pauljukov681]

Какого у него только инструмента нет, что бы несколько досточек сколотить😂

[@user-rj1nc7zd5j]

Разве наличие инструмента это плохо?

[@pauljukov681]

@@user-rj1nc7zd5j конечно хорошо

[@lostinthewoods357]

Nicely done! Going to build a set for the shop! Thank you!

[@DIY.Invented]

Thank you for your support

[@bittybigq]

Looks like a great idea. I'm making one.

[@shadowninja1474]

I would make two or your car will be tilted. 😆 jk

[@richardwallinger1683]

nice video . I use a throw away piece of cardboard for lying on .. easier slide at 75 years not so young mechanic .I fabricated two trolley jack fixtures to jack up my Citroen C6..

[@giampi555]

Ottima idea, molto bravo!

[@BlackwaterDSM]

Absolutely AMAZING way to waste $40 in wood instead of buying some plastic, 6,000 lb rated, PLASTIC “Rhino” ramps that weigh half as much and can be carried by a 6 year old. Way to go genius. 🙄

[@curtiswarner5880]

That's what l was thinking! He drives a Mercedes and can't afford a twenty dollar set of ramps

[@davidronquille7175]

Apparently he likes rolley things with those knee pads. Guess he really needed the wheels on the forty pounds of lumber though

[@JohnMiller-cd2cd]

Why 10 minutes?

[@3982snyd]

Or just buy a floor jack for same price as lumber..... Lol

[@CarolineLeinster]

We need to evolve beyond plastic .....

[@BRICKLAYERBOSS]

Invent something for the heavy breathing mr Vader

[@catlady8324]

Casters instead of non turning wheels makes it worse.

[@MrGenaGer]

I was about to say that. Swivels not for this application

[@johnklenzak1001]

I built my ramps out of 4 x 4 back in the 1970s to change oil and grease the car and my truck. My son bought me a metal set in the 1990s.

[@demarrmelton6348]

I made 2 sets about 10 years ago. 2x12's. Singles for the front. Duals for the rear. I used to do commercial vechile repairs.

[@ibrahimhaydar7062]

Hello pro You must concave the top end with a protrusion to hold the tires in place after climbing to ensure the truck does not slip. Have a good job ... New ideas come only after the prototype.

[@fabfabber]

I bought a pair of composite Rhino ramps at Auto Zone rated for 12K lbs about 15years ago for about $28. They even have a rubber foot on the end to prevent sliding. Strong and not heavy.

[@rorax42]

Great idea! Thanks for shearing!

[@ThomasNappo]

TO HEAVY....😂😂😂

[@oliabid-price4517]

What are the rotating castor wheels for?

[@user-xs5fj3ms2l]

I made my own years ago. I think mine were better. I used 4 2x10 boards and cur a 25- 30° angle, then put another board on top. It worked fine

[@stamengichev6883]

По-добре да беше направил две къщички за птици.А така-язък за хубавите дъски!

[@user-ko5ng6ro3g]

เครื่องมือ สุดยอดมาก

[@AgeofDoom]

Is it good for oil drain or do you need a pair on the rear wheels to be straight?

[@thisbliss81]

Depends where the bung is on the sump. If it's toward the rear of the car then this would be perfect

[@tomt.8275]

Excellent. What was the length and thickness of each board and what was the angle of their cutting?

[@arthurzettel6618]

My dad mad ramps like that back in the 1960s. Ain't nothin new. But then again what's old is new again.

[@hoffmanshaven]

Pretty slick ramps. Headed to the home Depot to see how much wood is.

[@babyboymoen2464]

I cant believe somebody called this amazing. I cant believe i watched the whole thing.

[@dancahill9122]

To anyone other than Americans it is amazing. i.e. foreigners, Mexicans, ect, ect.

[@Doctorwankinstein.]

This is many things..... amazing is not one of them!!!

[@dustinlerch9272]

I can’t believe you commented on a year old video.

[@Doctorwankinstein.]

@@dustinlerch9272 I'll watch and comment whenever I like!!!

[@BATTLESCARS75]

I can't believe those knee skates... ridiculous ha

[@mohammadkurniasuranata8660]

Mmmm... Whoooaaaaa.... Sooooo amazingly confused me... Nice idea

[@randyharritan7252]

Thanks for showing us how to cut an angle in slow motion

[@user-nx5cq9do9d]

Somebody needs to teach that guy how to use a saw

[@More-Space-In-Ear]

I would advise you to place a block under the back wheels next time you do this, your up a hill and it’s quite easy for the van to roll back...

[@juniorjohnson9509]

Sorry, but you cannot claim the "invention" of something that has been already made by the hundreds for decades already.

[@mm-mk7ew]

the invention is to number the boards so that they can be stacked correctly 😂

[@nathanbranham7384]

Why not alternate the 45 and 90 degree cuts to save the excess wood?

[@superglide6680]

My thoughts exactly.

[@AlymerKiteboy]

Why make the angled cuts at all? They serve no purpose whatsoever given the diameter of a car tire! The tire will only contact the top edge, not the angled face. 😂 Also, why use swivel castors? Fixed ones would work better and not wobble!

[@mjm9002]

Prachtig gemaakt, erg effectief 👍 Gr Netherlands/Holland.

[@reubendobbs8011]

Yes old hat, should use glue as well as screws.

[@charliedee9276]

Go to a bicycle shop and get a couple boxes the bikes come in. The large panels of each side are perfect for laying on, much better than the carpet. Doesn't wrinkle, easy to slide on and when the bolt or socket falls it is much easier to find.

[@NeverGiveUp-ib3xb]

Nice. Maybe block the rear tires.

[@dronready5727]

Я просто распилил бензопилой брус 150 см)) ну туп... Привет из России!

[@ericschneider7554]

If the purpose of the vertical piece is to stop the vehicle from driving forward too far, then I would suggest a design mod. Those horizontal fasteners will pull out under the load of a vehicle. Put a couple more horizontal pieces at the end of the ramp and install fasteners vertically. The sheer strength will be a lot higher than the withdrawal force your currently counting on.

[@vprn95]

Also, will the hammer action of the drill ( seems to be the norm now) effect the tensile strength.?

[@ericschneider7554]

@@vprn95 use of an impact driver in soft wood such as these 2x won't weaken good fasteners. However, one can definitely weaken or break screws made of aluminum or long drywall screws.

[@user-hx6xh6vf9b]

Столько лишнего дерева перевел, да еще "колеса" для перемещения этих бревен приобрел! Если есть руки и голова пандусы легко сколачиваются в виде коробов с откидной доской-легкие,практичные, мало места занимают. Смысл ролика в чем ?

[@MassimoSoldati]

Good idea. Thank you!

[@vahans1969]

Начинать видео нужно было с того момента, когда были посажены те деревья, из которых были изготовлены доски! Кстати, почему не пропитал древесину олифой или другим защитным средством?

[@sashasanich74]

Взял бы шпалу железнодорожную!Три реза бензопилой-4 подставки.Они уже и дёгтем пропитаны.Я уж больше двадцати лет такие пользую.И колёсики на фиг не нужны!

[@zurab1686]

Вес каждого трапа под 30 кг. Так то толково. Я себе сделал из бруса 100тки. Разборный. Сложность-перед поднять, это если заезжать в ограниченном пространстве двигаясь назад.

[@LuizCarlos-ly6cq]

Olá amigo, tive uma ideia pra você melhorar ...fazer dois furos em cada lado e perfurar um tarugo e colocar atrás da roda pra não retornar!

[@ikkuy852]

Seriously, all those dewalts tools is enough money for like 10 set of ramps or jacks and jack stands.

[@louieluna3039]

Thank you very much. Nice job 👍!!!

[@johnlucier1862]

My Dad made these 50 years ago. Stored them behind the bushes at the front of the house.

[@trustme7731]

Lets see, $75 in material and 3 hours of my time or $20 for garage sale steel ramps. hmm

[@Hambone571]

My thoughts exactly......

[@melemel2430]

WOW! Amazing. Holy s**t! Can't believe I didn't think of this. Dude you must have also invented the wheel along side with sliced bread. HARBOR FREIGHT!!! Get with it FRED. YABA DABA DO