Wish I Built This Car Ramp Years Ago

[@wdoxsee]

Love the way you have organized this video - clear, concise, no annoying background "music", you stick to the topic, and you treat the viewer as an adult by fast forwarding repeat operations. So many how to videos pad the show with unnecessary length, using 20 minutes to explain what should take 2 minutes.

[@muprock]

So true! Great video here. Other KZbin DIY and construction content creators, are you listening? If you want likes and subscribers, you need to learn to stop wasting viewers' time! 😃

[@FisherCatProductions]

Friend, I've been building my own ramps for 50+ years, and the swing away on this is the most clever alteration I have ever seen. At 72 I still like learning one new thing every day. Thx! Pr: 15:22

[@ronmit-p5g]

hey you know whats easier??????? just jack up the F-ing car ...this is like having a non 4 post lift that you drive the car onto ....just waste of time and money

[@hornyducks4090]

@user-fc1zs1wh9g jacking up your car takes way more time. This also costs way less than a jack.

[@johnholmes5674]

@@ronmit-p5g perhaps your head is strong enough to support the weight of the car when the jack fails and you are underneath at the time

[@georgenassar1953]

@@ronmit-p5g idk mate I started woodworking as a hobby a few months ago, now I want to start doing my own oil changes and such Don’t want to spend $150 on a car Jack so I’m gonna spend $50 on wood for this and build it with what I already have

[@RR-ds4sd]

@@ronmit-p5g would you get under a car like that? I wouldn't even with that ramp.

[@johnamador887]

Built a set of these last weekend after having 2 floor jacks that wouldn't lift my Explorer & Expedition. Went with 2x10 for the wider tires on the Expedition, also added a small grab handle on the latch side to make carrying them around a bit easier. Thanks for the short & concise guide.

[@mrnotnomis]

Grab handle is a good idea. I'd also add something that can connect the two ramps together for storage so that they stay together. Maybe some more of those hooks.

[@jeremyslaven4563]

@@mrnotnomis I’d say just grab ratchet straps but with weight your most likely going to move them one at time

[@mjenx86]

Great video, great design! My only concern- I would want to add more height to the 3” block on top. As you stated earlier, it’s easy for tires to climb a 2x4, so I think it would be good to make it harder to climb over the “STOP” block, and at the same time make it more apparent to the driver that they have indeed reached the top and should stop.

[@peaceman7321]

Yes! That was my FIRST and ONLY concern! Glad to know I'm not alone... !

[@DaneParksDoghouse1]

You could always add a piece to the back of the ramp. That way it'll still be stackable.

[@Rebar77_real]

You could add an air horn, or a rubber chicken. Bwwaaaaak!

[@jessejames586]

That was my first thought, too.

[@MrReivn]

If you have a low car, or long overhead from the tire to bumper, you can break something with tall enough stopper when driving the car on or off the ramp. I agree that something more rigid would be good, but you need to figure out a solution that fits your car, general measurements for that block don't apply...

[@richardbrant5728]

I did this decades ago when I had a very low car. Mine were about 6' long. I also chamfered off the ends of the boards. They kept scooting away instead of climbing them so I attached a 12" flap of tire tread to the end of the ramp. The car would get on that first and it would hold the ramp in place.

[@ericwrenfrow8349]

The tire flap idea is pure genius, even more effective than non-skid on the bottom.

[@imjabroni1]

@@ericwrenfrow8349 Someone commented earlier that a piece of rope will work for this as well.

[@tubbycustard8866]

im a lil confused, like you added a traction pad to the wood part?

[@ax75f92]

@@tubbycustard8866 think of a piece of tire screwed onto the low end of the ramp and extending onto the ground. The tire rolls onto the rubber first before hitting the wood

[@justinwong1307]

Brilliant idea! I need to do this

[@drumset09]

The thought put into storing them together, and not using the last 4 inches was my favorite part!

[@marlonfannin8074]

An addition of 1/4" of rubber material underneath the main base would do 2 things; 1) prevent the ramp from sliding. 2) Create enough space to avoid the hinged section from being in a bind with the ground or floor surface. It would likely put you over the $20 limit, but would add some safety!

[@stipcrane]

Good idea. My home-made ramps don't grip exposed aggregate concrete very well and front wheel drive cars like to spit one ramp backwards. My driveway is on an incline so that makes the grip even weaker. I used non-skid rubber foam, the type used under throw rugs, when my driving my front wheel drive car up the ramp.

[@silentknights5796]

He should have used wood glue in-between each of the layers of boards, this plus some bolts would have improved strength and safety.

[@marks3750]

Sliding ramps is the reason I quit using metal ramps. Plus they were always too steep for my 2002 mustang. The bottom of the front bumper hit the ramp before the tire. Been thinking of making some ramps. I would use 2x10s and maybe go a little longer on top.

[@silentknights5796]

I always had good luck with the plastic rhino ramps which are rated stronger than the metal ones.@@marks3750

[@SuperWiz666]

@@stipcrane You could make a bottom layer, detachable, which cancelled out the driveway angle. Wouldn't need much attachment. Pegs or screw bolts.

[@stinowyt]

Great video. Thanks for not doing a lengthy 30 min video just to show something so simple and straightforward. I wish there were more content creators like you. Have a nice one

[@2pugman]

I see a Nobel Prize headed your way !

[@viggosimonsen]

I made a similar set years ago - just not foldable. I didn't trust the flimsy plastic or even sheet metal ramps you can buy Here is what I added: In fact I found it necessary to make a slanted cut on the bottom board, to facilitate driving onto the ramp. Without that, I found that the car would often push the ramp around on the concrete garage floor. Once the car is on the first board with all its front weight, the ramps move nowhere. Also, I found that with wet wheels - and ramps - the wheels would easily skid. So I applied a coat of structure paint - actually just some oil paint mixed up with cat litter gravel. This is the same trick you sometimes use on boat decks to avoid slippery surfaces. There has been times where the lower boards were in the way, so I like your elegant and simple solution to that problem

[@robertheinkel6225]

I built one years ago, for my personal use. My ramps are detachable. During Desert Storm, I used the same basic design to get our KC-135R nose gear up high enough, to use a main landing gear Jack, on the nose gear, to change the nose gear tires. The tanker weighed about 150,000 during tire changes.

[@dwaynemcallister7231]

That's pretty cool, it's great to be able build your tools to fit your needs, my Dad was a A&P and commercial pilot who was great at making tools to make repairs while in remote locations, cheers to you!

[@lukemallory7832]

"During Desert Storm.." - now there's an opening to a sentence you don't hear every day..!

[@leonardhpls6]

​@@lukemallory7832 unless your on KZbin and some clown is lying out of his arse

[@edadams6698]

Bravo!!!!

[@trevorlambert4226]

Pretty cool. I don't think 6" is enough lift, so I'd make it 9", and 9.25" wide. Rubber padding on the bottom to grip the floor. The first "step" is worth cutting the 45 into, allows you to really wedge it in there at the start. A longer top step with a 3/4" high reverse stop would be nice.

[@JohnJones-qy5ko]

Yes, I'd feel better about a longer top step too.

[@johnsumner2987]

I was thinking of the rubber for a non slip bottom too. Can't tell you how many times my metal ones slip a little bit when driving up them.

[@Dominator9572]

Yes, wider sounds VERY wise. It would be very easy to steer off narrow ramps, and for the extra $$ would save a lot of headache.

[@flickedoff]

Ditto. The top platform needs to be longer and wider. And why NOT cut 45's on the ramp pieces?

[@RobMacKendrick]

Old tires are a good source of rubber. I use that stuff for all kinds of padding and gripping projects.

[@deirdre108]

I did something like this about 10 years ago but instead of using hinges I used metal clasps which allow me to completely separate the two parts of the ramp. This makes it easier to carry them, as they can be rather heavy. Part of the reason for the weight is that I used 2 X 12's as I found some 10 foot ones at a building surplus store. Plus the extra width damps down my nerves a little when I drive up the ramps! Also made a set for the rear so I can have all 4 wheels on the ramps which allows me complete movement under the car.

[@Jez1963UK]

Can you explain what you mean by metal clasps? I suggested making the hinge pins removable but I'm thinking your idea might be more practical.

[@deirdre108]

@@Jez1963UK Certainly! I probably should have said "toggle latch clamps" instead of clasps--something like you'd see on a heavy duty toolbox. If you go to that on-line store named for the big river in South American and/or the ancient mythical women warriors and search "Accessbuy Heavy Duty Adjustable Toggle Latch Clamp 4003 Style" you'll see what I'm talking about. I didn't use this brand but found something not quite as heavy duty at my local hardware store. I think this "Accessbuy" might be a wee bit overkill for the application but they certainly would do the job and keep the two halves of the ramp connected as you drive on and off. Hope this helps.

[@deirdre108]

@@Jez1963UK Certainly! The metal clasps would probably be best called a "latch clamp" or "toggle latch clamp". That huge on-line store named for a river in South America and/or for the mythical ancient female warriors has an example of a heavy duty model if you search for " Accessbuy Heavy Duty Adjustable Toggle Latch Clamp 4003 Style". I bought a less heavy duty version at a local hardware store in that I thought these might be somewhat overkill for my application. But these do look like they'd do a good job of keeping the two parts of the ramp connected while driving up and down them--which of course is very important! But if you look around you can find a lot of possibilities. Hope this helps.

[@eriklarson9137]

I am building my own right this minute. I am doing the same thing you did. I am also "trying" to rig up a chock system that will clasp in to place when I remove the ramp portion so the car cannot roll backwards until the chock is removed. I am also going to make something for the rear. Gotta change my rear diff fluid soon, so that will be the driver for that project.

[@johnnichol9412]

@@Jez1963UK As shown at 5:15 but maybe heavier duty.

[@elebeu]

This is a great idea. From the simplicity of using one piece of common lumber for construction, the hinge and hook setup, and the fact that they stack into a neat, rectangular shape.

[@CormacHolland]

I was already impressed by the construction and the video, and then he stacked them! Legendary

[@MuckoJumbie]

Really good & safe suggestions !

[@SVMSICE]

I built ramps like this a while back, not the hinging blocks but the ramps in general. I love those things! I had the metal ones many many many years ago. The issue I had with the metal ones was, lots of times they would slide quite a bit on me when I would be trying to pull the vehicle on to them. The wood ones are heavy and have never slid on me. If you live in a town with lots of new home construction, you can find enough boards easily in the dumpsters on these sites.

[@topherh5093]

Stay off of construction sites unless you have permission first.

[@SVMSICE]

@@topherh5093 unless it’s like gated or something no one cares if you are at a new home construction site. There are people there all the time looking at the houses for sale, rummaging through the trash, asking us contractors stupid questions, etc.

[@colomboisdoido]

@@topherh5093 Why do you care? Whenever I need a random building supply, I check the construction dumpsters first.

[@baldyslapnut.]

Just attach the webbing of a ratchet strap to the front of the metal ramps and roll it out back towards the car. The wheels will drive over and wieght the straps keeping the ramps in position whilst you drive on to them.

[@SVMSICE]

@@baldyslapnut. no need, I have wicked wooden ones 🤣

[@pollyperkins6931]

My next project when I get home. No criticism from me. Great idea thank you

[@crusinscamp]

I think you nailed it. My wood ramps (different design and admittedly pressure treated wood) are 40 years old and still in good shape. That extra length on the first board is key to keep the tire from just pushing the ramp forward when you start on the ramp. Someone else mentioned handles. I used a piece of heater hose with a pipe strap threaded through it. Yup, wheel chocks, definitely important. I realized that the time I set the hand brake and later found I could turn the wheel by hand, the hand brake mechanism was frozen from corrosion. On the other hand, under the right conditions, if the rear wheel can't move and you give it too much gas, you can shoot the ramps right out from under the car. The front end of the car drops with a WHUMP, don't ask me how I know.

[@kenwittlief255]

I think he screwed it.

[@paulyguitary7651]

“Don’t ask me how I know” 😂 operator error😂

[@joshopfermann5556]

He was probably pretty close to finding out himself when forgetting the wheel chock

[@carloscastenada7111]

I wouldn't think the wooden ones would be nearly as prone to being dislodged as metal ones. There's more surface area touching the ground than touching the tire.

[@Angrybutcher]

lol being 17 I did something similar with my CRX. Backing down ramps, took the chocks out, but had the ebrake on. Enough gas, front wheel shot the ramp out the front. That was fun...

[@1Jbeats]

I'm catching your channel for the first time. I love how basic you've made this, cheap, approachable, and possible with tons of different tools. Thank you for making great content

[@WhiteWolf65]

One possible addition, to make wood slip-proof: buy a dollar-store piece of rubber front door-matting, and staple it to the underside of the ramps. Then it will not slip even on very smooth concrete, or even wet surfaces. GripSafe! You could also make the ramp portion completely removable by using hinges without captive pins. The higher end-stop piece is also a good idea, but would necessitate a change to the over-all sizes of ramp-parts.

[@michaelzeleznik7609]

Great idea with an excellent presentation, quick and right to the point. All the needed info without all the unnecessary talk that often accompanies it! I've been meaning to build wood ramps for many years, and this solves the problems. Thank you!

[@barnandhome]

I love the simplicity! We have so much lumber left over from building projects I may just make a set. But - only thing I'd add is yes on the 45-degree cuts, just for looks, and a slightly longer top board for big tires, 2x10's, and finally a handle on the side. Nice work on the video by the way!

[@cartmanrlsusall]

Even without the 45s I'm blown away by how simple and functional this is ways to make it custom are endless nylon webbing for handles holes drilled for weight reduction even longer boards to eliminate the two pieces design are easily accommodated

[@LowetheTechGuy]

Sounds heavy but solid.

[@yeders]

Hey... I was thinking the two same things. My front tires are 235 wide and rears are 255. Did you make the WHOLE stand out of 2x10"s, or just the top piece with a 2x10 and used 2x8s for most of the stacked pieces? OR, somewhere in the middle, where the top pieces along the whole ramp are 10s, and the pieces underneath are 8s?

[@orbsphere-]

@@yeders I would suggest using at least same width on bottom as on top to help reduce stablity issues. Consider that 10's all the way up would make it a bit heavier.

[@orbsphere-]

An additional thought. If the same width of 2x isn't maintained from bottom to top the hinge won't work without some kind of modification being done for hinge attachment (won't be able to fold otherwise).

[@rusack7174]

Also, typical steel ramps tend to be too steep for lower vehicles, yours look to provide a more gentle rise allowing them to be used with more vehicles. Great project!

[@FisherCatProductions]

Exactly. Our low slung Merceded E320 will not go up a standard metal ramp because the ground effects plastic hits before the tire start to climb. Custom fit your verhicle before you start cutting!

[@waynedawson9695]

Made a set of these last weekend to change the oil in my lowered car. I used hinges with removable pins so I could totally remove the hinged part. Took a little hammering so I could easily pull the pin. They worked like a charm 🎉

Wow Wayne, that’s amazing, you’re the best sunshine.

[@michaelopry3456]

this is exactly what my grandfather used to do. as another viewer stated, smooth garage floors might pose a problem, glue and screw on some rubber on bottom for non-slip surface. great video, thank you!

[@YerBrwnDogAteMyRabit]

Excellent advice. I throw a piece of carpet or square of anti-fatigue mat under my plastic, slippy slidey Gorilla ramps and "painted" the bottoms of my diy wooden ones with rubberized undercoating. You can just give em a quick spritz with the spray can when you get a significant bare spot.

[@rupe53]

you are right. With a rear drive car, the ramps may skitter forward while trying to drive up, which is less problematic with a front drive car. Cutting the ramps at 45 degrees does help.

[@warrenharrison9490]

My then wife's grandfather had a set of wood 2x4 car ramps, I burned them. They were too old, dry and brittle.

[@ricksanchez3176]

Nice

[@SomeRandomGuy369]

Funny my grandfather told me and my dad to never do this. He was a mechanic for Ford and worked on everything from GT, Cars, Semi, Trucks and Planes. It's just not a good idea to trust wood. Thats why they don't make wood ramps for you to buy. When your under the car you shouldnt save money. Those ramps might cost 100 bucks but you need them. They are not going to give up on you. I own them and they are way stronger and wider and waterproof. Just buy them or dont work on your car.

[@nunyabisnass1141]

I made some of these for my boss about 15 years ago because i was watching him use those metal death traps you showed in the beginning. They werent collapsible like yours, but we used them for box trucks, amd they never cost less than $40. Now they are pretty much standard equipment at his shop because they can hold a huge amount of weight, very stable because they are so wide, dont sink into the ground and honestly just better than the metal ones in every way.

[@jamese9283]

Why are the metal ones death traps? I've been using them for 40 years and am still alive.

[@Jonathan.D]

​@@jamese9283 My neighbor would disagree but he's six feet under. He was pinned between the metal bumper of his car and the concrete wall of his house when his 14yo(or so) son accidentally went too far while trying to get the car up on the ramps. The dad didn't make it because the femur(s) were fractured and severed the arterie(s). He did survive for a quite awhile. The bumper kept the arteries pinched long enough for the medics to get there. They were able to use tourniquets to get him to the hospital. Unfortunately the ER doctors argued until it was too late. Eventually the family was given a settlement but, as you know money can't fix everything. While the ramp's design was not the only factor, there have been several articles written about how dangerous those old metal ramps are. It has to do with getting over that first bump, the steep incline, and their lack of traction. I personally think it also has a lot to do with the average person's lack of skills and coordination. My dad had a pair of those ramps that he used for close to 40 years without having an accident. He only changed them because he's old and wanted the new ones that are much lighter. They are also much easier to drive up on as well and thus require fewer basic skills. Now they just have to worry about technical issues like putting the right amount of the correct oil in the correct place. 😄

[@BH-gh6qm]

@@Jonathan.D your neighbor sounds like a moron

[@Jonathan.D]

@@BH-gh6qm You are right about that and it's hard to say otherwise. He set himself up for disaster. He didn't give himself an out. He let an inexperienced kid operate a vehicle. Plus he used the metal ramps that even some adults have a difficult time using. Back in the day he would have been trampled by stampeding bears or mauled by a hungry brown cow. 😄 I shouldn't make jokes but the guy could have won a Darwin award.

[@jamese9283]

@@Jonathan.D The way you described the accident, I don't see how you can blame the ramps. Any design can be made safer, but at some point it takes a little brain power not to hurt yourself.

[@JDLarge]

Guess you couldn’t hear me yelling not to forget that chock! Nice idea, I added two old used drawer pulls, one on each hinge side but at the balance point to make carrying both a breeze with one in each hand. Thanks for taking us along✌🏼

[@BornRaisedInCSA]

I made a set similar to this a few years ago... but I used 2x12's because of the width of the tires on my truck. I also made it 5 pieces high, as that was the height needed to bring the height of the lowered tailgate even with a loading dock (made loading motorcycle into the back a much easier task). Mine are much smaller (28" overall), so I added two pieces of 550 cord about two inches each side of CoG to make it easy to carry around.

[@benhunter9911]

Love these... then best part is you drive on the first board... and the weight helps hold them in place. My old metal ramps would always slide forward when I try to drive up.

[@rupe53]

only a problem with rear drive cars.

[@robertsmith2956]

@@rupe53 No, front wheel drive will do it on a smooth cement garage floor. I put anchor sleeves in my floor so I could pin them in place.

[@rupe53]

@@robertsmith2956 ... ok, let me rephrase that... MORE of a problem with rear drive. Lots depends on several things, like the angle of the ramps and how aggressive you approach. Obviously, there are always exceptions.

[@robertsmith2956]

@@poa2.0surface77 a running start will have the front skirt slide them forward before the tires even get there. I just let out a little more clutch, engine is going plenty fast. The ramp extensions I had to get for the saturn make it a nice gradual incline, well worth the money. And they come off after you are up it.

[@ghostridergale]

More gas , in other words using momentum to get up the ramps also don’t always work and in the long run could be more dangerous then helpful. Especially with front wheel drive if you’re power to the wheels decides to grab on the ramps more then the traction on the floor you could shoot your ramps right under your car. Then you’ll have lots of fun getting those ramps out from under your vehicle if the vehicle sits close to the ground anyway. Although if your vehicle sits higher off the ground you probably not need the ramps in the first place? I actually watched a person try using the gas as you mentioned it to get up ramps that did shoot a ramp right under his vehicle. Which was the wheel that had power to the wheel! Be safe and don’t get too carried away or it could bite you in the rear end

[@allthings2allmen]

I really need people like you around me in my life. We all glean so much from one another on a daily basis. I think of it like all the pennies in the jar that add up to even one good KZbin video! Pluss the fellowship and comradery of good 'ol fashioned friendship! Loved this idea and your video if that isn't already apparent! Keep up the good work brother!

[@BigFrankieC]

My grandpa made the unhinged version of these back in the early '80s. The hinge is a fabulous addition, also another commenter mentioned a 12" long piece of tire carcass tread area as a lead to the end of the ramp to prevent them from sliding away. All in all, a perfect little tutorial for garage mechanics on a budget.

[@kennethricher45]

Not bad. Honestly, I was doubting the effectiveness of these ramps and their quality. The moment the blocked wheel stopped you from backing up and the ramps held up, I was sold! I’m gonna make me some of these.

[@timstafford355]

been using these 2 by 12 ramps for 4 years on my semi's :)

[@christopherbuckley7544]

A better solution than hooks is loose pin hinges. Use two more 4 inch hinges on the opposite sides. Pop the pins out of them with and do one of two things: 1) Replace with a large nail or, 2) grind or file down the pins all around by a small amount until they drop in and out easily. You can also attach some wire rope to the pins and secure the opposite end to one of the hinge mounting screws. You could also do the same to all of the hinges and make the units fully collapsible and stackible.

[@RecoveryRoomRestorations]

you took the words right out of my mouth!!!

[@keithklassen5320]

Agreed; I'd be very hesitant to rely on those hooks, since they could be pulled out with only a little force, like a bit of extra throttle on the way up the ramp.

[@737smartin]

I was thinking of using toggle-latches…replacing both the hook and the hinge. That would let you completely remove the low part, making it use-side agnostic.

[@Riley512]

@@keithklassen5320 Up the ramp there is no pulling force on the hook. Down the ramp the force is divided by both sides and little chance the half ramp would turn outward.

[@dommyboysmith]

Even a set of those cheap slide locks for doors would work.

[@cozzoli39]

My dad built wooden ramps back in the 70s and they lasted all the through the 90s. Cheap safe and durable, can't ask for more.

[@victorjeffers1993]

Great idea and definitely a Great tip for those on a tight budget ! The only thing I might suggest is a thin peace of non skid rubber to place on bottom of ramps with adhesive glue to help keep ramp from sliding on slick concrete like in some home garages ! Thanks for sharing this video !

[@danatassler8776]

This is fantastic, and well-done. You did a great job explaining the logic. (Especially liked the reminder to consider having each entry portion swing outboard.) Thanks for the free information!!!

[@scruffy4647]

Really good idea. I built mine the same way, except I used 2x10s. Made the ramp top taller with more steps. Tried the screws at first but after several uses, the boards started separating. I eventually recessed holes and used 3/8" all thread with washers and nuts. I tried various stops on top but what really worked for me was a cheappy large mirror I had and positioned it so I could see when the wheels were on the top step. I could never feel the tire when it was against the stop. Mine are two pieces also. I offset the boards so when you joined them, they overlapped each other. Than it was easy to remove the ramp piece if you wanted to. Lots of good ideas out there .

[@JeradDS]

I like it a lot. I built one follwing your instructions and there are a few modifications I'd have made: 1. Have a barrel bolt instead of hook and eye. It may be where my eyes are located but they pop open too easily. 2. Angle the steps (I did all but the standing platform) 3. Extend the standing platform by 2 inches. It works fine as is but I want to be able to put something under my tire to prevent rolling. 4. I saw others showing it with a handle. My center of mass would be right next to the hinge joint... Haing a longer standing platform would help shift this. I also saw wheels but idk how i feel about that. 5. Make the ramp 1 layer higher. I am not sure how it would change the ability to balance but I like this idea theoretically. 6. Make the 3 inch piece a tad taller so I'm more comfortable driving up the ramp... 7. Add grips to bottom of ramp. Some rubber grips SOUNDS nice but im unsure how it would impact ability to have the leg slide out... 8. I used 2x10... I wish I did 2x12 but 2x10 are enough... I wouldnt do 2x8 because im not that confident in them. Notes: When not hooked, my wife said the leg swung out a bit when i backed the car down. Moving this is very annoying

[@wayneyadams]

The nice thing is that they are solid wood, so there is no worry about the quality of the welds holding them together, and the swing out feature is a great idea.

Do you have knee pads that go along with that comment?

[@mr-iz8cx]

@ no, you're the best. Have a star 🌟

[@redarrowsmk3]

Fantastic compact design! An alternative to hammering the hinges flat is shimming them from behind. This will preserve the finish :) Although sacrificing 2" of height, safety can be improved by recessing the final resting spot on the top board to create a better stop block effect and give the wheels no opportunity to roll back off the ramps.

[@tonywright560]

Great idea. Great video! My father was a marine engineer. He always built body stands out of scrap timber. So much safer than metal spindles. He would have loved your invention, both for safety and practicality. The only tweak I can think of would be to use pin type hinges that allow the swinging part to be lifted off and moved away after swinging them out.

[@rupe53]

30+ years ago I built something similar for working on big trucks. Used 2x12 lumber and added garage door handles on the side so you can carry with one hand. Also cut the ends at 45 degrees. Inside the garage I added some traffic paint to the floor for easy location of the ramps, for both width and fore / aft placement. That way they are in a good location to close the door in winter. The three mechanics that were there since I left thought it was a great idea and still use them. Now the bonus... we live in snow country so ramping the inside tire of the rear duals allows installing tire chains without using a floor jack. Just drive on up, and back off when done.

[@jeffarcher400]

Just gave me the idea of taking one board and cutting slots for the chains. Put it on the ground set it up and drive on top. Make wide slots so you can wiggle the chains a bit.

[@rupe53]

@@jeffarcher400 ... that won't work because you will be parked on a crosslink. If you must install chains with the tires on the ground, then you'd best have roller chains so you can remove a crosslink, drive forward to the blank spot, then put it back in after pulling forward again. That's how we did it on the road. Driving up on ramps (centered to the inside wheel) leaves the entire outside tire free.

[@jeffarcher400]

@@rupe53The slots are for the cross links??? I was thinking it wouldn't work for x type cables but for H type it should. They sell a plastic chain block. Weird chain patterns can be custom cut into the wood for particular applications. Agree that there's nothing better than having it up in the air.

[@rupe53]

@@jeffarcher400 .... cables? We're obviously not talking about the same class of truck. The stuff I was working on is 30,000 pounds and up. (fuel delivery, fire apparatus, etc)

[@jeffarcher400]

@@rupe53 Aren't truck chains the old H ladder design? I know trucks would destroy the cable design. I just meant you could change the slot pattern to custom design it for whatever you have. Lots of respect for the truckers. Out there day and night in all weather. Often risking their lives without fanfare. Cars only seeing an obstacle and not thinking about how things get on the store shelves. It's tough enough towing my boat. I wouldn't want to drive a big rig in town.

[@dontuno]

I'm probably too old to start climbing under cars again but what an awesome design. Think I'll share this with my son and he can do the climbing for me 😀

[@seanseoltoir]

If you're having to *climb* to get under a car, that either means that the car has a *serious* lift kit installed or you are really short... :) More like "crawling" under a car... I used to have a pickup that had so much room that I could sit under it on the concrete and do everything needed to change the oil and filter without even laying on my back... Plenty of room under there... And then there is my wife's current car that has such low clearance that there is no way my steel ramps will work and I have used 2" thick concrete blocks to make a stairstep ramp similar to what he is using just to get it up high enough that I can put a jack underneath it...

[@eriklarson9137]

I am getting up there and getting harder to get around. That is why I in the middle of making these. I am making it so easy and repeatable and SAFE to get under my car so changing oil etc will be a cinch. Spending a ton of energy on these so any time I need to get under the Vette it will be simple, safe, and easy. I changed his design a little. Added 1/2" plywood on the bottom level to get under my stupid low front end, and I added a entirely different stopper at the end. I want it impossible to go over my stopper. :)

[@MrTgpargolf]

Like what I see. Clear, no annoying elevator music over the points, shop in the background, don’t drone on and on to finish the product…New subscriber!

[@tangouniformromeoindia1117]

I do like the hinge and hook lock addition. I used 2x12x8's when I made mine a couple of years ago now. Made a set of 4 so I could get our SUV up high enough to work under the whole thing I used the measurements off a set of ramps my mom had. And I probably use them more than my jack and jack stands. Thank you for the idea.

[@jesseschooler918]

When you stacked them together I immediately liked the video and subbed to your channel. Top notch stuff man, you really thought of everything. Nice and affordable too. I like the way you think.

[@alertgasper]

Used to have wooden ramps in the 1970's...after splinters and oil soakings, went to plastic rhino type ramps for $15 used since i saw the metal ones break. Lighter to tote around and store inside each other, too.

[@dubmob151]

I have regular ramps already, but as a hybrid of this Idea, I roll up on a board as a pre-ramp to gain the added clearance needed for low slung vehicles.

[@derekst.gelais5261]

I did similar but I used plywood for the first layer. The car easily gets over the thin plywood and they never slide anymore. Also I added short steps on the back side so if i do go too far the tires wont go off a cliff. But this did add cost and weight. I do like the hinge idea looks like I may have to modify my ramps.

[@kbro7484]

Nice design thanks for the measurements and your time. The only changes I made were on your updated video concerning a handle and latches. To get a little more height and be within the height of my existing ramps, I also added one more 15" and added a one cut at 36" and shorten your bottom run to 24" so everything falls or aligns the same as yours.

[@southtexasspecials175]

I love it. The storage convenience is the best part .

[@ramathorn1982]

Better than my metal ones in my opinion. When I forgot to remove the tire chock when changing oil last, the metal ones shot forward since there is very little surface area for them to hold onto the concrete with. This resulted in the ramp hitting the oil pan I had collected in and sending it all over the shop. I think the wood ones shown here may have resisted that better because they have far more surface area contact with the ground...

[@roseymalino9855]

Tie a piece of rope to the ramps and extend it toward the car such that the cars tires drive onto the rope which will keep the ramps immobile.

[@ramathorn1982]

@@roseymalino9855 Thanks for the tip!

[@ianshand6094]

I've done that as well, and I suspect we're not the only ones. Front wheel drive, metal ramps, forgot to remove the chocks, went to back down, and the ramps shot forward and hit my adult son in the shin. Fortunately, no serious damage, other than a bit of swearing. Lesson learned, and could've been much worse.

[@carloscastenada7111]

They don't shoot forward if they sink down in the asphalt. LoL. SMH The metal ones are okay in a pinch, but I've straddled a ditch with a vehicle before so I wouldn't have to use them.

[@callendbott8404]

@@ianshand6094 yep that happened to me once as well, quite embarrising i must add. but you live and learn

[@railroad6601]

I like your design. Thanks for the video. I have been using a similar wood design: 1) chiseled the steps for easy drive up. 2) Using two piece design where first piece is the ramp and the second piece is a solid block of wood for tire to rest on. It just gives me a peace of mind.

[@antoniotutt4894]

I thought about this for years and with your video, I see it's absolutely attainable! Gonna construct 2 pairs!

[@ronreyes9910]

I like the "step" idea as with regular sloped ramps you have to use the brakes to keep the tires from rolling back down. Also I would spray them with some florescent orange paint and then seal them with some urethane as you'll likely get them exposed to oil, water, etc. A thin coat of RTV on the bottom would also help keep the ramps from sliding on concrete.

[@AndelaPandela]

​@Lurch Boys the point here was 20 dollar ramps to save a few $ on DIY car maintenance. Also, if you can't have grain running horizontal then explain bottom or top plates, upon which just about every single house on this continent rests?

[@ConReese]

​@Lurch let me know what you're smoking because I want some of that! Sure they might not last a few years but you make it sound like these things are gunna explode at the smell of a cars tires. The boards are fine in that direction because the compressive forces are spread amongst the boards and into the floor. The only risk really is splitting at the edge of the boards but if you were serious about building these things you'd be better off just PL'ing the entire thing and sealing the edges with the glue so it functions as a single block. Stuff is nigh indestructible.

[@seigeengine]

@Lurch ??? This entire comment seems very confused. We orient wood to take loads in the direction of the grain because that's how it's strongest, yes, but if you did that here, you'd be very likely to split the wood along that grain on the thinner parts. Yes, joists are oriented with the longer axis vertical, but that isn't because it's inherently weaker in the other axis. Joists are bent under the load they carry, and the taller the beam the greater the load it can carry... but these ramps aren't being bent, but mainly compressed, and the load they can carry isn't increased by making them taller. Plywood would probably be a better material, mind, but...

[@HoepRemains]

@@ConReese what is PL'ing? Asking for myself

[@ConReese]

@Dan Hoepelman it's a type of construction adhesive called litteraly PL made by a company called Lepage, the glue is so strong its stronger than the hardest hardwood bond there is so structurally the weak points become the wood itself and not the joint once it's glued

[@johnjly5295]

The only change I'd make is making the top platform a little longer so you can put the tire chalk behind each the front tires as well for extra security and safety.

[@stephenh5944]

it would probably take another section of 2X8 to do that though.

[@johnjly5295]

@@stephenh5944 yes but safety is important specially if you have a car that moves an inch the moment you park it. Also leaves less chance of the car sliding off when you cause the car to move a lot of you're using your weight to loosen something up underneath.

[@trs80model14]

@@johnjly5295 had thd same thought, I would make the top longer by a few inches

[@robertc.6441]

Great idea! Easy to store and won't have to mess with jack and jack stands, especially if only doing a oil change or minor repairs. Fat boys, like me could also make them a little taller and longer by adding a extra board. I would only also say just apply the emergency brake also with chocking the rear wheels. I have a bunch of wood laying around and some screws and hinges also, so I'm going to build me a pair of these this weekend. Most likely anyone could get boards for free from somewhere around town or neighborhood.

[@Profacy15]

I would use two hooks one on each side instead of a hook an a hinge. This way the ramp section could be removed completely and potentially used as the rear wheel chalk.

[@kreynolds1123]

And the ramp part couldn't bind while swinging on a hinge if you simply just remove it.

[@RoeRoe123]

It would be less stable for moving around tho.

[@Vincerama]

@@RoeRoe123 Sure, but just move four lighter pieces instead of two heavier ones. Lots of good ideas in the comments!

[@vdubjunkie]

I love the simplicity and functionality of the design. For years I've been contemplating taking up more of my limited garage space with some ramps, but I generally just stick with a jack and jack stands. I know there are times where the ramps may be more convenient, but I just keep on not adding them to my arsenal. Maybe one day, I will, and I think I'll use a version of this design.

[@PghNGDave31]

That's an awesome idea! One thing I would change is instead of the hook and eye latch, a set of tool box latches. Under $4 for a set at Home Depot

[@unstablenester941]

Love it. I'm going to make a set next weekend. For easy transport I will be adding a mechanism to bind the two units together and a couple little wheels at the end of one, and handle on the other, like a hand truck or dolly, when tipped up. Thanks for sharing

[@joerivas9847]

Made my own metal ones in HS shop over 40 years ago, our shop teacher Mr. Goo (American Chinese from Hawaii) was a certified welder. He taught use how to weld and tested our welds, before he let us build anything. So your wood ones would work too if you dont have a welder, good job. RIP Mr. Wilton Goo.

[@whatsit2ya247]

I remember a Mr Magoo from childhood, I wonder if any relation 🤔

[@rodneycaupp5962]

I have some stairway stringer material 2x12x12. I did a ramp like this long ago, but the genius here is it folds the ramp out of the way, with the Hinge addition. My Mustang insists on a set like these. For the re-undercoat I will likely have to do, and the AC repair

[@MrSonicAdvance]

I have an idea: Maybe angle the hinges slightly so as the split part of the ramp swings out, it also rises above the ground so it doesn't scrape on the ground or catch on an obstruction on less than very smooth surfaces?

[@klubstompers]

Forget the hinges make it so the ramp connects with a slotted cleat, so you can just lift it off or slide it out, so you can completely remove it. Make the top landing long enough, so you can have a 1.5" wide 1.5" deep slotted cleat behind the tire, so you can slide a short piece of 2x4 in to chock it, so the car doesn't roll back. If you dont trust 2x4 as a chock use a small piece of square bar stock. Now you have ramps, stands, and chocks all in one.

[@kevbu4]

@@klubstompers Why not both swing out or lift out? Just pop out the hinge pins and replace them with slightly under-sized pins or bolts. then you can swing it out or the pull out the pins. in fact, you could just use hinges on both side with this idea, then it wouldn't even matter which one was on which side.

[@klubstompers]

@@kevbu4 Yea, that would work. Just scrap the hinge pins and use a cotter pin.

[@jonnyozzy5288]

Just use lift off hinges and fit hinges at a slight angle which will lift the loose part as you swing it or use rising butt hinges

[@MrSonicAdvance]

I love how someone makes a suggestion and then a load of other suggestions come in to offer alternatives and improvements. Seriously, get a group of blokes together, and the possibilities are limitless. 👍

[@brianstuntman4368]

I made something similar a few years ago. It attached like an extension to the metal ramps that I already had, reducing the incline to clear the body of my lowered car. Once the vehicle was on top of the ramps, I could remove the extensions giving me more room to work underneath.

[@atomize1981]

Hi , I just built mine with 2x10x 8 feet lumber. I kept it simple and only 3 layers (4.5 inch height) without the folding stuff. Thanks for the inspiration.

[@jonoel6638]

My only concern is as you said that a tire has a pretty easy time going over the width of one 2x8. The top end piece is the same. It’d be pretty easy to go over the top especially when your used to feeling it step up

[@akjohnny5997]

i mean you're not going full speed up the ramp, just driving 1 mile per hour. not a big concern. source: i have car ramps

[@jonoel6638]

@@akjohnny5997 yes but you have one stop block at the top and a smooth transition while going up the ramps. These ramps you have multiple stop height steps. Source EVERY OTHER RAMP

[@EmbSys]

Good point. You could use the two leftovers to double the height of the stopper. This improves safety, but is paid by the reduced ability to store the ramps.

[@michaelt779]

100%. The design is garbage. He went too cheap and too simple. It's a simple mistake to forget the chock. It's also a simple mistake to select D instead of R.

[@TzUuup]

@@michaelt779 it was simply for storage. You can easily bypass that and put a bigger stop on it and lose the stackable storage option.

[@jordanl4805]

I'd probably add some friction material to the bottom to help prevent slippage. Also, adding a proper stain/coating will help prevent warping and cracks if exposed to water

[@lawrencegolba2244]

Maybe also add some grip material on top of the wood surfaces if you need to use them if it is raining or your driveway is wet so the wood doesn't get slippery.

[@lk-music]

I made some like this once to get a loaded wheelbarrow in and out of my garage's back door with a raised door, solid wooden ramps are heavy AF, but that was also the advantage we didn't want them to move about when we were using them.

[@munsters2]

Nice job. I like the way the two mate together for storage. 1. I would use hinges with removable pins so you have the option of completely removing the rotating part. 2. I would substitute a latch (not sure what it's called but found on some toolboxes) for the hooks. 3. I would like to see something a little higher for the wheel stop. 4. I think you can buy flat hinges but if not, you could router a groove or miter saw a small 45 to allow hinge to sit flat. 5. I would use some straps or latches to hold the 2 ramps together for storage. 6. I would add an additional piece of 1x1 or 2x2" to the top piece at the rear to keep vehicle from rolling backwards. In order to not mess up the way the ramps mate together, I would make these so they could be installed after the vehicle is ramped by using removable pins.

[@h82fail]

Agree. Taller (Hollow design so its less heavy). Hinges replaced with pin/hole where it can be pulled apart tool-less or design the wood to hook together the way the Eastwood plastic ramps do. Might as well copy the Eastwood dip where the wheel should sit, dip tells you when to stop pulling the car forward and it does the other things you said "to the top piece at the rear to keep vehicle from rolling backwards". The Eastwood ramps look nice enough to be worth the price but they seem overly wide and could be taller so that's why I am looking at DIY.

[@subbernh5192]

The pin idea would also work well for the taller front block to maintain the storage feature.

[@johnnylightning1491]

I made essentially the same thing for my motorhome but 3 layers high and I beveled the leading edges. I also didn't hinge the back part of the ramp because I didn't need to, but for your car I can see it being handy.

[@Devo491]

To gain a couple of inches of clearance, ditch the mechanic's trolley, and get yourself a sheet of twin-wall polycarbonate roofing, or corflute. You can slide around on it, easy as a trolley, but virtually flat on the ground.

[@edwardedward7974]

Well done ! I made my ramps using two sides of a wardrobe and several shelving boards that had been lying around unused .What I found was the stop block at the end of one of the ramps needed to be thick I used a 4"x4" block of wood otherwise the car has a tendency to ride over a thinner block .BTW the total lift height was 6" which made it possible to change the oil and the OIL FILTER ! on my x type . Cheers ! Eddie

[@davidb9323]

Ya I was wondering how many people Would drive right off the end

[@davadh]

I'm glad I saw this one, I think this design is the best of the ones I've seen on KZbin

[@SpecificLove7]

Wow, thanks!

[@michaelking42]

@5:50. You win Tetris forever. Great idea and design, well done and thank you for sharing!

[@ConemantheBarbarian]

I built ramps very similar to these 40 years ago. Mine were just a tad wider due to very wide tires on my Mustang. 2x10 bonds were my choice. Excellent project.

[@liquidmagma]

Aside from the extra weight, 2x10s would definitely be better. Why make it so tight with the size of the tires?

[@ConemantheBarbarian]

@@liquidmagma just a wider footprint for the tires to sit on. In my mind a bit safer.

[@liquidmagma]

@@ConemantheBarbarian I guess it wasn't clear that I was agreeing with you.

[@MrGraywolves]

I think if you went slightly longer for the top piece to allow for wheel chucks to be placed there. The "spare" wood piece could have a 2 inch wood dowel that would fit a preset pair of holes on the ramp top at the rear side. Drive up and drop the piece into the spot and voila, major safety improvement. It might mess up the budget, but does the budget also include a visit to ER?

[@HistoryOnTheLoose]

The idea of a rear-stop is great. I thought of it also. However, two inches of dowel protruding from the bottom of a (ostensibly) 2x thick block would bring total height of said piece to just under 4". Factoring in the radius of the tire. this would require lengthening the top piece by several inches in order to be able to drop the removable block in perpendicularly. A sliding-in-from-the-side, or a ratcheting slide rear-stop would solve this but add to the design and possible cost. I think we're on the right track, though.

[@knash97]

Just chock the rear wheels. Edit: Like he showed in the video.

[@HistoryOnTheLoose]

Right. And if the odd chance arises where you have to have all four tires in the air...where do you chock and what? I missed that part of the video. Nothing wrong with trying to elaborate on a solid design. It's why we don't still have to shoot single-shot muzzleloaders or drive Model Ts.

[@knash97]

@HistoryOnTheLoose 1776 you can't use ramps to get all 4 tires off the ground. If you want all 4 tires off the ground, you need a jack and jack stands. You're over complicating it, with adding a drop in stop that serves the same purpose as chocking the rear wheels. I agree that the end stop should be taller, though.

[@HistoryOnTheLoose]

@@knash97 You can absolutely get all four tires off the ground with two ramps and two jackstands. We did it all the time when we were kids working on our cars and trucks. Drive it up on the ramps, then jack up the back and use the jackstands. Now, where do you put the chocks? It's still on ramps, so could still hazard a possible roll (this time from off the height of jackstands). I'm not overcomplicating anything as much as just thinking. At any rate, why are you so concerned about me?

[@VicVelez-tf8rd]

Very well done. An easy way to keep the tires on 2 ramps without going over the stop blocks is to put the chok in front of the rear wheel. It should be the same distance ahead of the rear tire as the front tire is to the stop block. Also - the 4" scrap, an empty soda can or the like on top of the stop block, placed so that the tire pushes it off the ramp as it rolls into place. With the window open listen for it to fall.

[@NoName-ik2du]

Pretty cool. Only real disadvantage I see is that they don't have the safety lip that you drive over at the top like the metal ones. I always use chocks, but I like the redundancy of the front wheels resting down inside the top platform, kept naturally in place by gravity. Seems like something like that could easily be added to this design. Also, the increased surface area on the bottom may help keep the ramps from sliding. All my cars are rear-wheel-drive and tend to push the metal ramps as I try to drive up them (since their contact points with the ground are so tiny).

[@WhiteWolf65]

Add a piece of rubber door-matt to the underside and end of the 'ramps', so the tire pins the carpeting, down, and the ramps cannot scoot. Could use a piece of an old recycled floor mat from a former vehicle too!

[@charlesj.easleyii7642]

It acts like stairs more than a ramp, which is good cause the force is oriented more downward. The fact that there are no floating surfaces makes this naturally sturdy. I love simple designs, especially when they smack the standard model in the face lol

[@victormarinelli5660]

I designed my wood ramps, so the drive-up board is the same board that the tire rests on. The ramp actually flips up as you drive on it. It uses a lot less lumber and they're much lighter. The length and height would be determined by the vehicle's ground clearance, height needed and distance from the front of the tire to the front of the vehicle. It's basically one board with two blocks under it. One block at the front and the other about twelve inches behind it. The blocks under the board are about three and a half inches wide. There's also a small block on top at the front of the ramp. I believe they're about thirty-six inches in total length. Perfect setup for oil changes.

[@raymitchell9736]

Overall a brilliant idea! The one thing that makes me nervous about this design is that the wheel is not captured like the metal ramp side to side, I don't know if that is a real problem, but would be more forgiving should you not drive square onto the ramp. I'm sure there'll be more innovations to this design, I think you've started something great. Back in the day when I worked on my own car, I used the metal ramps, I see how good this would be to have that feature. Also I used Jack stands and chocks... Anyway, great design! Cheers.

[@SpecificLove7]

Thank you Ray, I didn't even think about the side bumpers because I'm always super careful when using ramps, but I can see how they can be a benefit.

[@railroad6601]

About the side rib, it would make the system less stable if the wheel sits more to one side. Remember the wheel is on suspension and it can have some side way force with the rib. I would rather have the wheel on a totally flat surface even with little bit of tire over-hang to the side than the situation mentioned in the above sentences.

[@robertsmith2956]

Only time I even had ramps in the way is when I am doing ball joints and cv joints. And I use plane jack stands for those.

[@robertsmith2956]

Go to harbour freight, and by a set of wheel tie downs, then screw them to the board and wrap over the tire locking it to the wood. But the hinge idea does give it a little more stability. A piano hinge style might make it even more stable. That other little piece can go inward at the front edge. OR go with 2x10x10 and get 2 more inches for your tires.

[@MikeBarbarossa]

@@robertsmith2956 A little more crude would be to stand a board on the outside edge of the ramp. just tall enough for top of the board to tire height. Now take a tie down strap and attach the board to the tire. It will lean in a bit and top of the board touches the tire on top

[@mt11235]

Great project. Few things I would add that would add little to the cost. First, I would stick some of that stuff you put under carpets or in tool drawers to keep stuff from sliding around on the bottom. Just spray adhesive and glue it on. Works well on phone cases too. Second, paint them with whatever left over paint that is probably too old already sitting in the garage to protect them a bit. At least the end grain. Lastly, I personally would have put some wood glue between the layers. Might be overkill, but would make me feel better.

[@liquidmagma]

The wood glue is pretty unnecessary, but the anti-skid stuff on the bottom is a good idea. Worst problem with the metal ramps is them sliding away while trying to drive up onto them.

[@Guillotines_For_Globalists]

@@liquidmagma Wood ramps of any kind are an improvement due to the larger surface contact area with the concrete, unlike metal ramps which have very little surface area against the ground.

[@20121961]

That's great! I'm going to make these, just as soon as I've converted all those measurements to metric, not living in the US. 😁 I had no idea that wood would be so strong!

[@YoderTexas]

I would suggest boring a series of holes in the boards to lighten the weight of the ramp. The holes could be 3/4" to 3" in diameter and drilled completely through the boards. You could remove a lot of material and not compromise the strength of the ramps. Next, add a carry handle to the outside of each ramp to help you tote them back into the garage.

[@thefunkyt]

What a great idea! I have some old 2x8 laying around and was headed to harbor freight for ramps this week, not now! Appreciate it!

[@UnkleAL1962]

same here - now the garage wants $80 for an oil change. I ordered a filter wrench for these new fangled oil filters and will go back to doing it myself - but I didn't want to revert to the 70's and use those steel ramps which always made me nervous.

[@thevanvirgin]

My nerves, my sills and my knuckles thank you! Splendid design!

[@thinkingoutloud6741]

You can really extend this by making one for all 4 tires. Then you can build an extra tall platform in an additional section that you slide in place and attach to the front of the ramp in a way similar to the ramp portion. You can get some nice clearance that way, but you might want to stay with 2 x 10s for stability.

[@marcuspidek2273]

Nice job. Maybe screw on handles for easy carry?

[@MrHeyhomes]

This guy gets it. The most important thing about ramps is space used up to store them x

[@speedlever]

Nice design! I’ve thought about building ramps from 2x10s to help with low slung cars, but the inability to remove wheels to rotate tires or do brake work killed that idea. For low slung cars (Subaru WRX, for example) that sit too low for my long frame floor jack to slide under to reach a central lift point, I use a couple short 2x10s under the front tires to get the front end high enough my floor jack can slide under far enough to reach a front central lift point. Then I slide 6T jack stands under the pinch welds. I move to the rear and my long frame floor jack is able to reach the rear differential (rear central lift point) and lift it up and slide jack stands under the rear pinch welds. Now I have the car level and all 4 wheels off the ground for whatever service I need to do as well as tire rotations and brake checks. If my jack couldn’t slide under the rear, I could have used 4 short 2x10s under all 4 tires to give enough clearance, but in my example WRX above, only the front needs the extra clearance.

[@therogers4432]

As a fellow WRX Owner (1996 JDM V2 pushing close to 320bhp at the flywheel 😁 that I imported from Japan to the UK back in in 2005 😊👍) I can picture everything you describe perfectly, and have a set of 4 solid ramps that I cut from 10"-12" pine tree trunks with a chainsaw to give a stable 8"-10" wide base and 6" of lift (because I'm quite bulky at 6'/185lbs), with a very shallow angle of inclination (around 12⁰ IIRC?) matched on all 4 ramps. The pair for the front axle are 18" longer than the rear pair, and stepped at 3" tall for that initial 18", which allows the front end to raise 3" first, avoiding damage to the deep front chin-spoiler, and then I stop, get out, attach the shallow removable stop-blocks I made to the front ramps, and slide the pair for the rear axle (without stop-blocks) in front of the rear tyres with *just* enough clearance under the sills (with plastic side-skirts, of course...) beneath the rear doors, before that amazing symmetrical 4x4 system pulls my Baby 🥰 squarely up onto the 4 flat surfaces at the same time -the first time I used them I did screw 2"x1"x10' long battens to both sides before driving all the way up, to keep everything where I needed it to be, but this later proved to be uneccessary as the wood is soft enough/rough enough to grip the asphalt driveway where I use them just fine. I hope you get to enjoy your car more than I currently do mine, but only returning 6-8 miles from a gallon of 99RON gasoline 😢 (at the equivalent of just over $14/gallon... When I can get it, because very few gas stations here will stock 99RON because it deteriorates so quickly, and so few people will pay the extra for it... 😡😤🤬), and nearer to 3.5mpg if I drive her as she was designed and built to be driven 🤪👍, makes my beautiful little white WRX something of a rich man's toy in the (frikkin terrible... 😳) current economic situation here in Britain, huh? 😭

[@carportshenanigans5918]

That’s a slick setup there! I made some a couple weeks ago out of some 2x4 cut-offs that my wife pulled from a construction site dumpster. Mine were extra simple and only took about 10 minutes to make, they are my dedicated oil change ramps. At only 3” tall, they’re useless for anything else, but suit their specific purpose very well. I may make a set like yours, I love how they fit together for storage too!

[@billpetersen298]

I'm impressed, at, your wife. She sounds like a keeper.

[@carportshenanigans5918]

Lol, yeah, she is. I almost have enough pilfered 2x6’s to make the forms for a concrete pad I’m about to pour!

[@chillyballs555]

Just curious, shouldn't you have your car on level ground when changing the oil?

[@carportshenanigans5918]

@chillyballs555, in a perfect world, that would be ideal. Conveniently for me though, the drain plug on my wife’s Toyota is at the back of the oil pan so it works out well.

[@carl-uk1774]

Sir , that is a brilliant idea and a very easy run up for the wheels, and being that the wood is laid down means that it will take any weight. The opening lead up is very clever and I way well make my self a set. Only different feature I would do is to make the top part a few inches longer so that I can choke the front wheels too. But thanks for the idea, Brill👍👍

[@scottmorris4914]

Besides chocking the back wheels, you should also set you parking brake. Good idea. I have never liked car ramps, was always concern that when I got to the top of the ramp, I could roll over the stop.

[@kenmathews4522]

I saw a tech in Virginia working in a car that was on a 4 post lift. It was down. He somehow managed to knock it in gear. He is paralyzed from the waist down. Please chok wheels on both sides! And just be safe

[@davidwillander9010]

Great idea.....but was thinking also to add hardware to attach them together and maybe a leather handle to carry ......and obviously a French cleat on the side for easy storage!

[@SpecificLove7]

Good thinking

[@hanslain9729]

I kinda like that square end to the board(vs 45). Gives the tire something to grip as you drive up them. Thanks for this!

[@AGlimpseInside]

These are such a good idea. Surprised something like this is not commercially available. Really good idea bro

[@SpecificLove7]

Thank you Chris. My brother-in-law told me I should market them, but they are definitely too heavy to ship.

[@davidholtrop6429]

Years ago I had seen a metal set of ramps similar where the ramp came off. I thought the ramps were to short and made it to short to get a low car up very easily, I just didn’t think they looked very safe, being made out of stamped steel. These are heavier but look safer. 👍👍👍

[@darrylschmidt704]

Hi. I did something similar to this with three layers of 2x12s which are not high enough. The width is safer and I made the top longer but I like your design. I cut 45 degrees angles on the ends and they still fit together for storage. I also did this to make it easier for less experienced drivers to use. I used large eye hooks and chains on the sides to make handles for carrying. I plan to add another layer but will need to add wheels on the end of the thick parts so I can roll them vs carrying them. Adding the hinge is a great idea. I always use the parking brake but the chock is a good idea. I wonder if there is a way to add a removable chock on the top of the ramp...

[@Sylvan_dB]

removable chock: dowels and holes. Just keep grain strength in mind.

[@dojorat5363]

I love this idea. It cures a lot of problems associated with metal ramps--especially the sliding when you're trying to drive up on them. Thanks for the idea! But where the heck are you gonna store the behemoths when you have a small workspace? I know, it's a conundrum.

[@ghostridergale]

As a few others mentioned the extra stop block, one other thing to consider is to make the bottom board rough where it be harder to slide on you. You could glue strips of 80-60 grit sandpaper to the bottom board or even put some sand in a small can of paint and paint the bottom of the board. Might even be able to take a chain and hit the bottom board with it to rough up the surface of your bottom board might help too? A few choices to try to keep your ramps from sliding on you !

[@viperbananas]

You want to use rubber or urethane to grab the cement

[@gtonram]

You could probably take an old workout mat or rubber mat that is thinner and attach it to the bottom of each ramp, to keep it from sliding

[@vdubjunkie]

In theory, I like the idea of a "grippy" bottom, but if your garage floor is painted, you don't want sandpaper against it. Really, you only need to keep the ramps from sliding as you climb them. Once the car is up, they aren't likely to slide, unless you've polished the floor! :P

[@theglengineer]

@@vdubjunkie The car wheel 'pushes' the ramp along, before it grips the ramp and goes up. To keep from sliding, attach a piece of 1/2 inch plywood under the lowest 2x8 that is longer than the 2x8, so that the car's wheel starts on the plywood and holds it all in place. Car won't 'push' a 1/2 inch piece of plywood.

[@johndoe6032]

Cool project. Looked into buying some ramps a while back but never thought of making my own. It would be faster and I would feel safer than using jack stands. But because the 1 1/2” height is so easy to go over I would be worried about driving over that last part and destroying my car. It would make the stack as nicely but I would prefer a taller stop at the very top. Also, I know you chock the back wheels but I would prefer something also against the back of the fronts. Maybe some threaded inserts in the backside where the part swings out and screw in a verticals 2x4 for extra wheel security.

[@J.T.19134]

I was gonna say cut the extra piece in half, and stack it on top as an extra stop block. I personally would put a 2/8 on a hinge on the front. That is able to stand on end, JIC something happens, ie: car slides it could help you from being crushed to death.

[@gohdux]

I’d use a toggle latch instead of hook and eye and I’d also put them on both side and install a carry handle. That would add another 20 bucks but it would stop pinch points and when married together more predictable. I may do this. I’ve got a truck an suv and a bmw. The bmw needs this.

[@zedmelon]

To install the hinges, you could also turn the ramp onto its side. Drilling/screwing down is easier than to the side. Slide it against anything solid (e.g. back of the workbench, the other ramp, a wall) to keep the parts aligned. Good idea. Good video.