How to make adjustable power supply using ANY computer power supply unit

$2 for 10 PCBs (2-layer, 48hours lead time): jlcpcb.com/e
How to creat PCBin a factory • JLCPCB Factory - 2-lay...
Adjustable power supply from computer ATX! • Adjustable power suppl...
Adjustable power supply 0-35V 0-5A • DIY excellent adjustab...
part 2 • Adjustable power suppl...
IR2153 got.by/2ph4v6
6N60 ali.pub/2jpsaf
MBR20100 ali.pub/2jps56
600pcs resistors got.by/2jhbvc
PCB board ali.pub/2jps83
Voltmeter, ampermeter ali.pub/2jv08b
Buy power supplies
1600W
shopeasy.by/red...
1200W
shopeasy.by/red...
1000W
shopeasy.by/red...
600W
shopeasy.by/red...
500W
shopeasy.by/red...
shopeasy.by/red...
200W
shopeasy.by/red...
My multimeteres
ali.pub/2i2mrz
ali.pub/2i2msk
ali.pub/2i2mu4
My power supply ali.pub/2i2nc0
My oscilloscope ali.pub/2i2mr0
App for calc.trnas play.google.co...
Follow me
Instagram / akakasyan
Facebook / kasyan-tv-139150916827430

[@Basement-Science]

This is quite ingenious, adding your own bridge rectifier while leaving the old one to regulate the voltage. You could even still use the original 12V output at the same time.

[@sleepwalkerbg1]

Hi Kasyan. Excellent an creative idea but here are some suggestions. Adding capacitor after FULL BRIDGE RECTIFIER ( ;) ) is not good idea in hard switch topology because of inrush current. You are endangering primary switches (transistors) and you also lowering life expectancy of that capacitor in rectifier. You should add a storage inductor that acts as a passive buck regulator and attenuates output electrolytic capacitor's inrush current. Best regards.

[@MCsCreations]

Amazing work, dude... That's really useful!!!

[@arrevunella]

This is very interesting but there is one thing I did not understand, what is the difference between taking the 24V like in this video or using the blue wire as negative?

[@electronic7979]

Excellent project

[@ginzburgi.9251]

Good job, very comprehensible.

[@rahulwaghmare6370]

I like n love ur all video n voice that u nicely discribe

[@TelredesCursos]

Muito bom! Parabéns

[@hemantmundhe6662]

Nice video,specially sort circuits demonstration.

[@ashbe77]

Great job,thank you so much.

[@ltronics62]

this is excellent. thank you for providing this info!

[@filenotfound__3871]

I have a problem: I did the thing to get 24V DC, I used FR203 diodes in a bridge...and got 55V. How? And how do I step it to about 40-45V witch is the maximum my buck converter will work with?

[@aravindwilson1558]

Did you got any solution???

[@filenotfound__3871]

@@aravindwilson1558 I got a buck - boost converter lol. Altho i think the issue might be qith the group regulation choke on the output.

[@aravindwilson1558]

@@filenotfound__3871 thanks for replying ❤️ Also I tried adding choke from a nother atx psu still didn't worked - getting 40-55 v

[@shehryarshaheen7115]

greate work dude. this is the real solution

[@MedSou]

Thank you 👍👍👍👍

[@suryapatnaik5720]

If we don't need 12v or 5v can we remove those factory diodes and toroidals and capacitors in secondary side?

[@Brokendiode]

No, these power supply's operat in a deferent way than you might think, not all of the voltages are well regulated, these are switching power supply's that regulate the 5 volt supply by providing a sample to the PWM regulator that drives the high voltage mosfets that drives the main step down transformer. This means that the 5 volts is highly regulated and the rest will very a little with there own load but may increase slightly as the 5 volts is loaded down. Without the 5 volts the output will just run wide open, and very with line voltage, and with load on any remaining outputs, that's why some of these power supply's have to have a load, or load resistor, applied to the 5 volt supply to work properly, otherwise the filter capacitor, will with no load satisfie the feedback loop and let the regulator cut back to an idle, causing the other loaded outputs to sag or drop out altogether.

[@filenotfound__3871]

I did it...and killed my PSU...

[@ThaDIY]

Thank you

[@passtranelectronics]

excelente

[@theconquerorstv506]

how do you connect if you have power supply module. do you have to make diode rectifier or can be connected directly to power supply module

[@moshiurrahmanmeraj6640]

Please make a video on variable dual power supply with output short circuit protection , it's more necessary then single power supply . thanks. Love from Bangladesh 🇧🇩📶📻 👍.

[@hennochoi]

As long as the ground and the negative lead of the power supply aren't connected the output is floating which means you can connect 2 power supplies to have a variable power supply with negative and positive voltage the only issue is if you want to keep the 2 voltages the same without manually adjust them but that can be fixed pretty easily (check tracking double power supply)

[@robertanderson8613]

Great show exactly what I've been looking for except I want to use a server psu or two for 24v and more current will this circuit work in that situation? Or upgrading parts to higher values? Thank you

[@rohandabir1588]

Very nice make a video on inverter sine wave

[@MrRonychakraborty]

nice as always

[@suryapatnaik5720]

Not getting output from additional bridge diodes on the transformer. My smps has 2005z chip. Please help, or give tips.

[@ksrawanlab5986]

Awesome

[@jeetendarkumar4514]

Please make a video of how to make a mini toridol transformer

[@rawandjaza5929]

So can not use bridge rectifier diode like kbu808 it’s 8A?

[@tanyalobyam]

What program you use for making panel?

[@rpg9995]

Thanks man ❤😘 btw in video i saw ic SD6109 but in circuits daigram it is TL494,i got sd6109 model tell me how to modify it

[@Qaiserhayatkhan]

good video

[@jimw7916]

Why do you call a regulator a "stabilizer"? and Why do you call a heatsink a "radiator"?

[@tolgadabbagh1877]

i tried to bypass the inductor at a high power smps . the mosfets get very hot very quickly . so something is missing in this design .

[@tolgadabbagh1877]

also when you connect positive and negative 12v together they will already have the bridge rectifier if you connect them after their factory diodes before the inductors you will still get 24v .

[@bm830810]

that puny heat sink cant handle 70W continuously for sure, maybe add a switcher preregulator

[@amanhameed7114]

I do this practical but result is not good. A large amount of ripple produced. Not every supply have same design. I do different practicals to convert ATX power supply into bench power supply but a lot of ripple produced and other design fault. I not recommended that modification in ATX.

[@mohamadaldarwish6678]

I love your voice😍😍

[@vishva8kumara]

You can't really control the current. The current can only be measured and limited. The element/load decides the current it will conduct at its given state.

[@tolgadabbagh1877]

they call that limitation " control "

[@willylimas998]

i have try and put diode bridge to that 2 pin of 12v and then psu wont start, anybody can tell me why ?

[@Themachine615]

I have 165VDc 15a power supply. How can I safely step down and make adjustable? Thank you

[@SimpleEnough2k9]

Please share a picture of that beast !! There should be quite a few secondary taps on the transformer so you should be able to find an appropriate voltage to suit your needs. I'm really surprised to see that much voltage and current for a power supply but I guess there's always a first time for everything.

[@jatinmali9310]

Just use step down converter

[@king24km]

why mine has 40-50volt output on sscondary trans when i add the diode and the capacitor(35v2300 ùf)?

[@aravindwilson1558]

Did you got any solution

[@kahitanongmaisip9358]

sir kasyan tv im super fun of you please can you make a UHF VHF amplifier like antenna booster RCA please please i always watching youre vids and i make it please :)

[@ErkanOkman]

👍👏

[@tylersheehy3918]

In computer tecknolgeys we have a standard rule don't open power supply even if it's been off for a while

[@misium]

you have to wait two whiles

[@pradipselectrolab2994]

What? If somebody do not have the ATX Power Supply you are using.

[@tolgadabbagh1877]

watch it again , then , again .

[@e.h.lipton73]

Sweet lady comprehensive standard modifications for atx do not exist, true. But YOUR KNOWLEDGE to reverse engineer does. SO SHOW US HOW YOU WOULD DO IT,,,! Then,,, WE LEARN! Never mind, I jumped to conclusions again,, did it because of opening statement. You in fact are truly trying to teach us how. My apologies dear lady.

[@ParthBhat]

Amazing!, But I have a question, if the core amps is limited to 3amp then how at the output of the 5v/12v/3.3v we have amperes upto 20 or 23amps? Just confused about this part. And thanks a lot for sharing the video Cheers!

[@e.h.lipton73]

Sweet lady comprehensive standard modifications for atx do not exist, true. But YOUR KNOWLEDGE to reverse engineer does. SO SHOW US HOW YOU WOULD DO IT,,,! Then,,, WE LEARN!

[@aakashtiwari3677]

Can you please make a video on 3 Phase MOSFET based Diode Clamped Multilevel Inverter? Because I have taken this topic as my Engineering Final year Project.

[@rameshchandrasahu2195]

please say in Hindi language because your ponaunsment is very good but some people are unable to understand.2nd things components value is not showing properly.

[@SimpleEnough2k9]

That would pretty much explain why some people, like me, have so much difficulty to understand hindi speaking people when they put their english "ponaunsment" skills to practice ! Seriously, english is an international language, much more than Hindi, so if someone wants to reach a large pool of people with their video clip, doing it in english will most likely be the way to go. Which component values did you miss ? Beside the HER505 diodes, the 2200uF 50V capacitor, the 10K and 100K potentiometers, there isn't much shown here. Don't forget to look in the description too as there are quite a few links that might be of interest too.

[@Sergey_Bobrov]

Hi is Russian

[@tolgadabbagh1877]

learn english .

[@horacewonghy]

12-（-12）=24？

[@FlyingShotsman]

Try typing it into a calculator. [. . . . .] Mind blown, eh?

[@Basement-Science]

yes you can get 24v that way, but the -12v is only for low power, and therefore 24v is too. Not sure if all ATX PSU are happy with a load between these though.

[@reeseyme9613]

voltage are relative to one another thats why. like stacking 2 AAs battery in series and take center as ground you get + and - 1.5V at each end then a total of 3V in series.

[@Deep_Thoughts99]

How you maintained the short circuit protection?

[@Basement-Science]

if short protection is on the primary side, it will work. I assume that´s where it is normally done? Otherwise you would have to monitor every output rail separately. Edit: Actually, it shouldn´t matter where the short circuit monitoring is, since the transformer cannot generate any voltage anymore if one of the rails is shorted somehow.

[@TheJavaSync]

Is It 3A max? Is It posible more A?

[@nick5625]

TheJavaSync buy a buck boost converter from eBay for 40€ for up to 50v and 30a or buy a cheaper one for less v and a

[@diecksl]

@@nick5625 At that price, plus the ATX power supply (if bought new) this gets close to the price range of a (cheap) chinese regulated power supply (30 V/5A).

[@nick5625]

Lejf Diecks 1 to be waiting this video you probably have an atx power supply , 2 you don't need a power supply a 12v transformer with a full bridge rectifier and some capacitors will do, 3 you get 50v 30a which is much better.

[@nick5625]

Lejf Diecks don't forget your 1500 watt fuse 😜

[@Pantera13g]

For 5A, change aditional circuit in this video with +Kasyan TV Adjustable power supply 0-35V 0-5A, check kzbin.info/www/bejne/laOWkHqgo9x8aKM

[@irfanjalal2010]

I need 0-35 v Amp Circuit board from Jlcpcb ! will u help me for it m from pakistan !

[@robsonszpanic6485]

I made that and got FUKKEN 60V, HOW? I HAVE NO IDEA.

[@robsonszpanic6485]

I NEED HELP PLEASE I'M GETTING CRAZY HOW 12 + 12 IS GIVING ME 60VDC?

[@KasyanTV]

This is the amplitude value on the capacitor. Connect a small load, then measure the voltage

[@robsonszpanic6485]

Now I understand.. But how you did it with only a 50v capacitor? Why it didn't blow up?

[@robsonszpanic6485]

And feeding the Tl494 with 60v isnt a problem?

[@aravindwilson1558]

​@@robsonszpanic6485how did you solve this problem tell me in detail pls

[@user-sh5do6ry4v]

касьян и нашим и вашим

[@kahitanongmaisip9358]

sir kasyan tv im super fun of you please can you make a UHF VHF amplifier like antenna booster RCA please please i always watching youre vids and i make it please :)