How To Make High Power Led Light At Home 40 Watt

[@milesmoore5422]

No Calculations, no resistors, but it got a million views and 312K subscribers thus far ? Must be the quality workmanship I'm guessing.

[@mohimadvani6425]

😁😁😁😁👌👌👌

[@draculareloaded2151]

Good vedio forget about rude comments. Ur vedio is perfect for those who want cheap aquarium led lights . All they need is use one red and blue led and two white led . This combination will make it a grow light. For aquarium we need to work them for minimum 7 hours continually . So fan is a must . Thanks for Ur vedio . Great

[@m.p.juggler7250]

Craftmanship in perfection. I would try to get heatsink paste and hotglue in buckets, so you just could throw the parts in, to make sure it is really everywhere

[@khan-xz2zy]

Direct to 12v battery. Bravo. U will earn so much from this scientific revolution.

[@erics.7942]

Cool idea and not bad for the first time you're working with COB's but... Electronics need work before you blow up those COB's, soldering job is barely adequate, mount screws go through the holes in the not in the corners and please work cleaner.

[@mohimadvani6425]

very messy when you apply the heat sink compound

[@sandipsaha3958]

Kya is ke sath koi driver add nahi kiya ja sakta tha? Ta ki bijli me bhi chalata .

[@princestudio7575]

please suggest me a bright led light strip (approx 25-30 watt max) for mirror, this LED strip i want to put/place surrounding on a shaving mirror

[@colinkraus7139]

I like your project. I have led chips on the way and i need to know how to mount/cool them before they get here. Thank you for the video.

[@kuyajayyoutubechannel6327]

What paste did u use to fix the led?

[@sasasaponja]

What if I want to connect 6 pieces in parallel to 12v. (12V to 14.5V in boat).? Which driver then use?

[@abunghermawan4601]

wow,, amazing. i remember to my playing in Basic School

[@reynaldomaldonado]

Terrorific terrorific proceso de fabricación

[@jaackmcmahon8757]

How hot does heat sink get after extended use, say 30 minutes?

[@akbarali9317]

video achih hai lekin ap ne yeh nahi bataya k in pr kiya lotion lagaya hai?paste ka nam kiya hai?

[@urchmanogboo6265]

IS THE CONNECTION DIRECTLY ON THE BATTERY NOT GOING TO DRAIN THE BATTERY QUICKLY?

[@rajkishortrivedi6904]

Please tell value of power supply and calculation of total load with fan counted. Good vedio.

[@bennyfata1293]

Havent you heard "resistor" buddy?

[@a.r.gunjal]

Bro use 240v, 135J capacitor and make a bridge rectifier using 4007 diods and connect one 50 v 47 uf capacitor and at the positive end of rectifier use 40 ohm 1 watt resistor...the led will work directly in 240 v.

[@jumcopper]

can that also work on a straw hat LED? and what are the connection diagram pse.

[@Bachulia]

hi man , it's ok , do this circuit need a resistors ? or it is conectid to cd suply?

[@INFOMINE10]

12v 1m adapter can support one led chip ?

[@bilalahmadbhat4607]

You will get a Nobel prize definitely or an Oscar at least. Guess that you should have a bharat bhushan with your name !!!

[@lamsimbala2335]

Tidak pakai resistor?

[@pardeep_vlogz]

Whst is use of fan ?

[@simple2851]

friend. Do not you use drivers? Then how can turn 40w light without driver

[@davidchi6580]

donde agarras Las LED lights , para hacer uno como el tuyo

[@ramshankardhir]

Sir, thoda detail mein samjhate to achha hota. Led white ya led warm ? Sahi quality led kese choose karein ? Led price ? Kahaan milega sahi price par ? Led ka lumen ? Ye Jo unit aapne banaya he ye kitne lumen ka bangaya assemble hone ke Baad ?

[@ramshankardhir]

Kese him Kharid sakenge bataiye.

[@gowriprasanthvm]

@@easytechzones Where didi you buy led? if online pls provide link.

[@congache]

You need todo work more carefully And less mess! This is terrible work and poor soldering. Always tin with solder before you connect wires to contacts. Screws too big, wires too close to heatsink can cause short, before applyìng paste be more careful & professional not to make such a simple mess (your making a video for others to see). No need for fan with that huge heatsink and 40watts only makes about 98 degrees Fahrenheit. Practice first so you show a more prof job on video cause this is very poor workmanship. THE IDEA IS NICE ..PRACTICE I MUST SAY!

[@yogeshbhat1]

Good tips of advice worth noting. thanks.

[@neocortexlab]

as a noob i liked this video...

[@nanoparticle5988]

@@neocortexlab - Yes, I agree this video has good ideas even if not done to perfection.

[@mathquik1872]

why you don't just stfu and get yourself a pizza ?

[@mathquik1872]

Best part: Wires could cause a shortcut hahahahahaha and what's then? Will the Lights go out? Or will a plane crush into your pea brain

[@nazikrieg]

I have followed the neceassry instruction except that i am using a multiple ac/dc power source. Why is it that when i switch on the light, the fan stops and when i switch off the light. The fan runs. A little help may do. I have little knowledge of electronics but i know most its parts needed. Thanks!

[@NirmalSingh-ft4rn]

Hello Sir main solar panel ke sath chalne wali streetlight banana chahta hun please help me

[@easytechzones]

220v or 48v dc

[@jefersonsiebel1336]

Olá vc saberia me dizer quantos leds desse posso ligar em uma fonte 12v de PC ?

[@Bachulia]

I have red, green and blue one like this and I am scared to connect directly without resistance 1 or 5 ohm 10W. what can you say about it.?

[@hristijank2]

red and yellow are rated at max 7V with heatsink, with normal operating voltage of 6-6.5V 1050mA, blue, green and white are 9-10V, but they can take up to 12V with heatsink. lead acid battery fully charged can reach up to 14.4V. id reccomend u get a 10W resistors 5.7 ohm for the red and yellow LED chips, and 2.2 ohm 10W resistor for the blue LED

[@tabahtabaha2688]

Bacho Danelia ufjjggdk

[@sekicustom6226]

Love your videos but I was just wondering where can I get some of these led lights from

[@grimreaper7862]

Amazon

[@poiiihy]

No current limiter??

[@SadIndiafr]

Very good

[@hindu7180]

background music Ke Badle explain Karte to better Hota

[@faruksodha7734]

Keya bike ke liye led light bulb banaskte he

[@sanjaybhunia4818]

Bhai wo bada wala LED kahan Milta Hai........

[@easytechzones]

Koi bhi electronics shop pe. Jaha pe parts milta hya

[@waqararshad7047]

Very nice

[@elektronika922]

You first need to learn how to propper solder a wire! You heat that wire to much on a plastic switch witch can be damaged. Add tin before solder two wires. All wires must have tin on it and than you just need to touch them with soldering iron.

[@jantonio991]

Where is the LED driver? So I do not think that lasts long those LEDs

[@srujanreddy6699]

No need of LED driver, as they are 12 volts COB chip LEDs.

[@MegaInformazione]

you're wrong! current limiting resistor is needed!

[@srujanreddy6699]

No, even I made this kind of light and using as an emergency since 6 months, nothing is needed.....just connect to 12 V DC, 2 amps. EASY TECH is correct. You are wrong.

[@srujanreddy6699]

There is difference between voltage and current. Voltage should not increase 14 volts for this LED chip, current can be any number of amps, no restriction..

[@MegaInformazione]

Is not the correct way to power a led. You were lucky because the high internal resistor of the battery. In other case you'll blow out the led. Yours was a very big mistake.

[@bobhill2821]

shabby workmanship

[@fanellyde6859]

Can we use this on 12 v choke

[@AbhiGblackbird]

What's the ampere limit it can resist ?

[@tomikari6192]

what?! what is this?! 4x10W = 40W math. 100x10W = 1000W If I find a driver with the right current, it's no big deal. It only costs more than buying a complete one. not to mention its casing is ready to buy, it's aesthetically pleasing, I don't even remember. Existing stuff is not difficult to make, starry sky is the limit. Need to build a led driver! Make an LED, not a 10W-20W battery, if it succeeds, show it. There is nothing in it. Basic electrical knowledge is already possible. And the net is full of such self-proclaimed geniuses. Those who play it reach into the drawer, take out a handful of led batteries, power supply, and unexpectedly put together a series of 10W led panels. From the stuff you buy, it's not a stunt. For example, if you make a space cabin out of a refrigerator, which is pressure-resistant .... well, or you make it from waste, it's not an artwork, it's a really useful, usable thing .. yes, that's something. This has already been done on another channel. Even bigger. You must have seen it, too. What would you like to show? How can you make it? They succeeded. Congratulations, Ellemben didn't make much sense. At least make something that is not yet in the fray. No copying, little bit of variation, plagiarism.

[@jawedansari9963]

Konsa wire kaha Joda jata h koi batayega

[@nkanilkumar4060]

without a current regulator The LEDs will be damaged in a matter of hours. Very poor soldering. using the soldering iron to shrink the rubber tubing is a very bad idea. First you learn how to solder.

[@dannie197832]

use it from dusk till dawn and it will not last long. current limiting resistor is needed. i've done this.

[@anusaksatun5208]

เค

[@jkoz292]

I have the led's and need to wire 6 to boat battery. Please explain more on resistor or current regulator! Thank you!

[@shalinibiju7249]

ഇത് എവിടെ കിട്ടും ലൈറ്റ്

[@marcusorillius6971]

It’s not that impressive at all. Can do that with a blind fold.

[@jda7274]

Bang saya mao pesen bikin rangkaian lampu kaya di video bisa gak ?

[@mumtazahmeed8746]

Nice what neme for whit colur paint

[@DCC_DHAKA]

Sir heat sink kaha milega Or price kya hai

[@mdrafiqulalam6932]

nice.. ican used 12volt adapter on input volt.

[@tamtruong3458]

What the hell is it ? Where is driver for led? Can't connect directly power to the led like that , don't do it wrong way to build led..

[@atakansisman9134]

what is it name leds below gray thing?

[@sukhwindersingh3035]

Aap ko nhi lagta Hole kam kiye h abhi jgah or h

[@Gabriel25037]

Alguno que me diga que eso es pasta termica y no es plasticola por favor (Someone plz, tell me that is thermic paste and not school vinyl glue)

[@ankitkumardharmendrakumar3201]

Sardar charging light 3.7 volt cut cut banana hai to Kaise Banayenge

[@emonkhan7325]

Led price plz

[@danny0885]

Noch ein lieter wärmeleitpaste😜

[@snreng7866]

nice bro.....

[@faruksodha7734]

Green led milegi

[@АлексейКоверник-й8д]

А где защита светодиодов от перегрева если вентилятор сломаеться?

[@കീലേരിഅച്ചു-ജ1യ]

What about the working time in that battery

[@jssallinonetrj1247]

Y light kuch time bad dim Kyo ho jati h (5mint)

[@wasimalammazumder6499]

Great

[@traveller4750]

10w led price

[@universalexpress7930]

Rs 20

[@vaishalipatil712]

Not really in the local market it costs rs 10

[@Abdulgahfoor007]

Poo waooo

[@TechBzzod]

Nice

[@imransameer9286]

pori video ma naya kia tha ???

[@gamo98]

useless soldering job all the joints will fall apart

[@mathquik1872]

not really..

[@dtwistrewind7361]

Yes mate agreed tin the cobs then tin the cable then Solder together so the cob doesn't receive as much heat, those are some brittle joints.

[@Xnova290]

Yes useless

[@ameervoice]

great

[@goldpro7549]

Power

[@ekiapriliady1522]

Bagus.. Tapi banyak minusnya.. Kurang rapih Kurang aman Kurang perhitungan Tanpa LED DRIVER??😫😫😫 dan sayang dana yang di keluarkan.. Selebihnya 👍👍👍

[@OK-qt8ge]

Led driver gmn?

[@makiaa2009]

OH GOD, my eyes. WHY. please watch how to solder and then post videos. OH GOD.

[@BankingPoint-en3kf]

Sir e pipe Ka name keya hain

[@BankingPoint-en3kf]

Joint ki uper se jo black pipe Hain uska name kya ?

[@albertomuru4353]

Perfecto

[@shivamlights2725]

is thre is need of fan for cooling.....

[@hristijank2]

if u use a heatsink of that size u can safely operate 2 leds without a fan, but in any case it will extend the life of your led chips

[@maaqibali4424]

Sooo Good Sir

[@sayedmaruf7871]

bro have a question how many price of battry ...

[@sayedmaruf7871]

tnx/tnq/thanks/thank you for given answer... 😊😊

[@ajithkumarak4925]

kzbin.info/www/bejne/oobVZJqjqZqbp6c

[@mohmmadrafiquesheikh2270]

Nice work 😃🤔🤔😱

[@zamanghazi9972]

Plz apni Awaz k Sath video banaya kro .. Aisay theek samajh nai aati...

[@HoangNguyen-yk1yn]

Needs driver dude .

[@aestus187]

LED light in the 40 watt range.

[@easytechzones]

Cob?

[@michelloona1384]

never seen a montage of leds as badly done§§§§

[@lupuzcustom1620]

awesome custom,,,,i sub u

[@hudaFamilyVlog]

Akinya cepet tekor brooow.

[@ZulMasriAl-Kampary]

That hot glue 😢😢😢

[@markquinn7593]

Good job but messy good luck

[@timothygodfrey4950]

I hope know one lets you near anything with more than 12 volts.

[@mathquik1872]

boobs

[@poiiihy]

bruh

[@heyheynowinga9972]

READ *******as long as the fan blow toward fins not away its inefficient to suck air past fins its common sense THIS LOOKS LIKE HE HAS IT WRONG

[@mashedpotatoes5323]

Lmao the direction of which way the fan blows is the least problems this thing has.....

[@romantashevRT]

This battery will be drained very fast:)

[@MegaInformazione]

*How NOT to power a led light!!!!!!!!!!!!!!* Where's the current limiter resistor????????

[@3goldfinger]

Looks like video is from India, they never clean their irons.

[@biscuitfpv6281]

Craftsmanship and quality are a thing, Just not your thing clearly.

[@mukeshkumar-dd2np]

make a led chaser ic number 12f629 please make bro

[@PRABHUDEVASHASTRISP]

You Suppose to be engneer maga, even for 12v supply u used wires like this, what about 11kv supply ...........

[@vanniyo8988]

Alright, now put it to good use and grow some weed

[@kanishkadamsara4483]

Nice bro

[@arghyaghosh6020]

Puthandiya Tech tu tv cgdhygjig