When I first watched this video 10 years ago, it became my dream to make such a small rc plane. Fast forward to now, I build at least one every week!
@maikolrodriquez10 жыл бұрын
cheap,looks pilot-able,and looks easy to make...U MY FRIEND.... DESERVE A COOKIE!
@ib42200013 жыл бұрын
One of the most meticulous and loving how-to videos online. Thank you. You are a master!
@Rich77UK4 жыл бұрын
Wonderful build of one of my favourite ww2 fighters. Excellent job.
@tyoukogatalabo7 жыл бұрын
Plan & Manual trhk.exblog.jp/14699325/
@Gas31910 жыл бұрын
absolutly fantastic work..
@normanmendonca28346 жыл бұрын
That's a very nice micro plane. Fantastic sterring set up. Thanks for sharing with us. Regards from Australia.
@AxelBitz4 жыл бұрын
I don't know about anyone else, but I also need a tutorial about that wire foam cutter!
@peteohm4 жыл бұрын
Easy. Put weights on the ends of a nichrome wire with ends draped over the edge of the table. Use 2 same diameter drill bits under the wire to the thickness desired.
@bryanewyatt4 жыл бұрын
I'd love to see how that rudder "servo" works.
@AngryHybridApe3 жыл бұрын
.010 smooth guitar string and 12V power supply connected to 2 screws on a flat table. String stretched tight between the screws.
@AngryHybridApe3 жыл бұрын
@@bryanewyatt thin magnet wire wrapped around a pencil 25 times, slid off the pencil and superglued to hold it together. A small neodymium magnet that will fits through the hole. Current will make the coil move one way or the other. I dont know the voltage. I would start with 1.5 volts. The actual wraps around the pencil im not sure about. But ive seen them before. Im guessing 25 -30 wraps the thinnest magnet wire you can get. Power up 3.0 uses it. But I highly suggest not buying them. I bought 2 and theyre horrible.
@pakistanhobby1st5373 жыл бұрын
I make a tutorial
@joemelton47474 жыл бұрын
This will go perfectly with my mini pearl harbor
@menone26064 жыл бұрын
Ha ha,, saw that coming. KZbin *" JOSHUA BLACKENY JAPAN BITES BACK "*
@joemelton47474 жыл бұрын
@@menone2606 you may have seen it coming but the Americans didnt
@joemelton47474 жыл бұрын
@Vanargand and my other nuclear bomb
@joemelton47474 жыл бұрын
@Vanargand after the shogunate takeover
@AsianAntman4 жыл бұрын
Joe Melton I WAS THINKING THE SAME THING
@wordreet10 жыл бұрын
Excellent That looks like fun! Bright yellow for visibility, good for my old eyes. :¬)
@XxJJxX1313 жыл бұрын
Very nice. I was thinking about making something like that, but I wouldn't want to add a motor until I get some more experience with the components needed.
@Tractor-boy14 жыл бұрын
Don’t forget to register that as a killer drone lol
@uniondeltatangoalfa12 жыл бұрын
Congratulations!! This is the kind of video I was especting. Thankyou Sr.
@Nirabulator10 жыл бұрын
Thank you for posting this video. This is a cool idea! I have just subscribed to your channel and will explore your other videos.
@chrisfettig10 жыл бұрын
Nice! now i know what to do with my old 2 channel rc plane that has all these electronic components already! it was one of those mall indoor rc plane toys. has the magnet/wire loop rear tail system and everything. :)
@MrROTD13 жыл бұрын
awwww what a cute Zero :)
@eelcogg10 жыл бұрын
300gr is the lightest plane I've ever built. This thing is 100 times lighter. You sir, blew my mind! I never expected that building small requires a whole new set of skills.
@fogliamaroccootmane404910 жыл бұрын
micro system controller pleas?!!!!
@dibyojyotisinha14264 жыл бұрын
It flies unexpectedly well!
@rotorismo5 жыл бұрын
Sugoi! I am building also a brushed version of a Mitsubishi A6M. But it's going to be somewhat bigger and with 4 channels.
@Spastilake11 жыл бұрын
its an Actuator instead of an Servo Motor... its an hand wound coil of "painted" copper wire ;) the paint acts as an dielectric fluid so its avoidin shorts between the windings :) if you put an source on the coil it would make its own magnetic field and will pull the static magnet to itself :) and into the other direction if you invert +/- hope you understand what i mean :D my english is not the best... please correct me if iam wrong :D
@yuch76725 жыл бұрын
Where is the two lines of the coil to be connected?
@afonsoyoshimura34003 жыл бұрын
Congratulation!....The Zero airplane fly friendly
@wicqedeyebot563110 жыл бұрын
awesome......you are very smart....thank you for sharing your knowledge
@orojasp12 жыл бұрын
Great video @toyukogatalabo , thanks a lot for this video tutorial! Just a question, you always use spektrum (dsm2) on your receivers? there is another option for those tiny little marvels? Best regards,
@yanksguy2310 жыл бұрын
You sir, are amazing.
@PHILG6410 жыл бұрын
Very Impressive!!
@ki-bp8mo7 жыл бұрын
Phil Galati
@RossiaIsNoMore6 жыл бұрын
How much time it can be in the air with this little accumulator?
@mr.k11777 жыл бұрын
Very relax and lovely video.
@mosfet515 жыл бұрын
Beautiful work.
@454charing13 жыл бұрын
in cutting the foam from the layout i i use scisorrs
@ozvooky12 жыл бұрын
where are the plans because when i go to the website the plans are not under the plane and what is the length
@legocandytube58719 жыл бұрын
You should make kits and sell them. I would buy it for sure!💸
@helimodelismofacil99044 жыл бұрын
Congratulações nice work
@mjgeertheninja10 жыл бұрын
Where did you get the parts! This sounds like a unique project, and I totally want to do it. Where did you get the reciever and controller?
@bradz200312 жыл бұрын
you are brilliant I have made the same before i saw this as well as i nano jet using an electric prop incases in a tube and another prop behind , I would love to see your idea of a jet could you make one and post the video please, last i have to use receiver from old double prop helicopter but its too big where can i buy the small receiver you used in this video thank you
@thijss127210 жыл бұрын
how works that magnetic servo system?
@user-zn7zo1lm6w10 жыл бұрын
depending on the direction of current in the coil, magnet, mounted on the keel, is attracted to the left or right side. thus rudder gets deflected
@thijss127210 жыл бұрын
thanks :) i can use that system
@Noah-bt5lb9 жыл бұрын
rc boats yeah, same concept of a speaker. copper wire with a current creates an electromagnet that acts appon the magnet deppending on the direction of the current.
@joewoodchuck38245 жыл бұрын
@@user-zn7zo1lm6w How is the coil current and polarity controlled? Normal receiver output would be pulses of varying duration for a servo instead of what appears to be analog current control.
@aliberkozderya31125 жыл бұрын
@@joewoodchuck3824 As far as I know there are some receivers that are meant to be used with these magnet and coil actuators.
@rjramos27756 жыл бұрын
Salute for your creative mind
@AshiquelIslam10 жыл бұрын
Wonderful, thankyou
@ImCorpZ9 жыл бұрын
there's no pitch and roll, it can only yaw. still a great project :D
@billbergen91695 жыл бұрын
Good for learning. its called a 2 channel rc plane. You can mount the motor so that increased thrust will make the nose tilt up.
@TIRCQ11 жыл бұрын
Great, thank you for share your knowledge :)
@allanooi52764 жыл бұрын
Ko, no sound from your audio recording.
@wmjeletronics45976 жыл бұрын
unbelievable!! congratulations
@obscurvevo8 жыл бұрын
that plane is a masterpiece! how do you combine art with aviation?
@OoNnUuRr00711 жыл бұрын
If I made a prototype of the aircraft was not exactly what I want, but you give all the dimensions of
@piggypie88813 жыл бұрын
hey im just getting into this stuff and was wondering if you could do more vids like this thanks
@briandstone1able5 жыл бұрын
Excellent!
@loomismeister10 жыл бұрын
4inches is 100mm by the way, not 200mm like shown in the video intro.
@Fireholder110 жыл бұрын
101.6mm, actually
@krishnashah638611 жыл бұрын
hi i can try to make this but i dont make its coil part plz tell me hwo to make this .because its tell does not move left or right
@hansomerocket10 жыл бұрын
How to connect wire from coil to receiver board?
@martin.k2403 жыл бұрын
with velco tape ..... six years later
@hansomerocket3 жыл бұрын
@@martin.k240 hahahah.. im still here... 6yrs man
@martin.k2403 жыл бұрын
I thought you ment how to connect the receiver to plane never mind I dont know how
@altamashshaikh748010 жыл бұрын
excellent and cheap... how many number of turns in coil
@gabrielmuniz485511 жыл бұрын
and this plane so that you have it with another plant itself is mi?
@locouk13 жыл бұрын
Awesome! Thank you for posting this.
@socotril11 жыл бұрын
Hi, good job! I have a question: The model RTF weighs just 3.54 grs??? And the battery weighs less than 1 grs? Thanks you. Cheers from Argentina.
@sagarborate98217 жыл бұрын
#nice video but can you say how to measures CG of your micro airplane??? plz answer
@andremendes51168 жыл бұрын
KONNICHIWA, 3.43grams, It's very nice job man... I appreciate!
@AngryHybridApe3 жыл бұрын
So make the CoG slightly nose end heavy with elevators in slight ascending position?
@NBC_NCO4 жыл бұрын
Very good!
@grk65111 жыл бұрын
Excellent job, I don't have the patience or time for that. Very cool plane. But watch out for that mosquito, he's going to take your plane out :) lol
@phyrr26 жыл бұрын
Paint is so heavy for a little plane though! Try using markers instead. Takes more time, but much less weight :)
@saito12510 жыл бұрын
Chris Cavaliere, it's not a saw, it's a hot wire foam cutter.
@scallan745 жыл бұрын
Fantastic video!! Thank you
@eissa.n222011 жыл бұрын
the only question is how did u make the tail turns left and right
@nikemamut86682 жыл бұрын
Mantap mas 👍
@MitchellGWhitehead5 жыл бұрын
Amazing video my friend!
@krishnashah638611 жыл бұрын
but i can try that to make this plane.and make it but it does not fly so plz tell me your airplane cost mean rupiess in indian
@hi326711 жыл бұрын
where are the printout plans???
@flt84210 жыл бұрын
What paint did you used??? Tamiya?
@nikhil_u8 жыл бұрын
Super impressive. Where did you get the transmitter from? The TX DSM2 E-Flight.
where shall i join the other end of the copper wire in the receiver ?
@tonywright82943 жыл бұрын
Superb A+++++
@waynepaul40319 жыл бұрын
How do You Control the Rudder ?
@jthibis13 жыл бұрын
Hi, where i can buy the transmitter, the reciever and 4mm moter pop? I am from Brazil, and I need some Shop that ship to Brazil! Thanks for all
@solehaiqbal24838 жыл бұрын
where is the plan to download and print
@neonuser4565 жыл бұрын
People who wanna make this, you can buy cheap electronics that's used in this video for under 20 dollars just buy the RC e-bird and use its parts on this.
@jflstudios43428 жыл бұрын
How much did everything cost
@NikhilSinghMusicOfficial3 жыл бұрын
Can u give me a link for buy the receiver and transmitter link which can ship to india
@Hufekf329 жыл бұрын
Do you think you could make one of these using parts and electronics from a toy rc helicopter? I think that would make a great video
@ruke1ire10 жыл бұрын
5 people are jealous. Awesome vid:D
@zero0101one11 жыл бұрын
Really Amazing!!! How could you control the vertical climbing without flaps?
@mindbuilder87685 жыл бұрын
power, if its faster, it climbs higher, if its lower, theres no lift, so it will go "lower"
@BaddaBigBoom10 жыл бұрын
Is the adhesive cyanoacryllate?
@howelx11 жыл бұрын
anyone else think " that little plane still goes farther than the bombs korea is making"?
@APKTV10 жыл бұрын
Hello ! Could you mail the receiver and transmitter ??? I am from Russia .
@postaktr10 жыл бұрын
Super práce...Kde je možné stáhnout plán?
@DHCUNHA3 жыл бұрын
Where do I find this servo motor?
@TheTurd123410 жыл бұрын
How long does it fly? Per charge.
@Ahmedali-no1nf10 жыл бұрын
Very nice
@EPICOddOtaku8 жыл бұрын
can you give me the link for the design for print
@ananthmuppidi76299 жыл бұрын
how does the rudder work?
@Febeleh11 жыл бұрын
Very nice.
@marvan18 жыл бұрын
This project looks amazing, but could somebody please tell me how all the electronics connect? It isn't made clear in the video.
@l2ic38 жыл бұрын
+DonkeyPlonkey123 of Awesomeness What would you like to know?
@marvan18 жыл бұрын
l2ic3 Connecting the transmitter to the receiver and making everything controllable is not made clear. In fact, the video wasn't too clear on the electronic elements of the project as a whole.
@mehulpurohit92459 жыл бұрын
very nice Rc-plane ...but how i get remote control and the receiver what if i make remote control and the receiver what that will work please reply.
@gamer_pro24458 жыл бұрын
where do you buy the reciber
@RussiaRules23412 жыл бұрын
love the music
@jeffyboye97398 жыл бұрын
Are you soldring the coil into the receiver
@ajmgtr14 жыл бұрын
hello sir i would like to know what type of glue you use and the brand please thank you very much