How to manually light a pellet stove

I show you how I manually light my pellet stove.
Thank you very much for watching and God bless.
✅ My T-shirts. Thank you for supporting my channel✅
diy-jim.creato...
5% off shirts use DIYJim2021 when checking out
✝Bible ESV easy to read amzn.to/3qshNQP
✝Bible NKJV amzn.to/30ns322
✅Titan Solar Generator (large generator) poweredportabl...
✅Copyright free music and sounds artlist.io/Jam...
✅Sony ZV-1 (camera I use) amzn.to/3MxVeG2
✅sony wireless UWP-D (mic I use). amzn.to/3LEPV6m
✅Go Pro that I use amzn.to/2WC6WXH
✅Wireless mic used: Rode Wireless Go amzn.to/2WxQt7c
*Full transparency. I am a participant in the Amazon Services LLC Associates program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
*Disclaimer - Thank you for visiting my KZbin channel. Please understand that the content on the DIY jim KZbin channel is intended for informational purposes only. I make no warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information posted on my KZbin channel is strictly at your own risk, and I will not be liable for any losses and damages in connection with the use of my KZbin channel.
#lightapelletstovemanually #Harmanpelletstove. #Harmandidnotlight

[@jeffreycaban5107]

I've had several Harman Pellet Stoves over the years and replaced the ignitior on all of them at one time. Harman used several different manufactures over the years so the Ignitor that lasted 10 years might not be the same brand Ignitor even though you purchased from an authorized Harman Dealer. I've had good luck with the Ignitors from Pellerhead/esesstoves. Regarding lighting the stove when the Igniter is dead what I do is this: I take 91% Isopropyl Alcohol put about an ounce in a cup. I add a handful of Pellets shaking the cup to coat the Pellets. Let the Pellets sit absorbing the Isopropyl for a bit and then pour them in the Burnpot. I take a lighter and light the coated Pellets and they fire right up.

[@DIYJIM]

Awesome I might try that. Thanks for the tip

[@hubster4477]

Hey thanks! I see many ways, gels, hand sanitizer, etc to manually start the stove but most favor the torch, now i see why! Thanks again!

[@DIYJIM]

Thanks for watching

[@patriciagordon6486]

Ill try this. Mine is not a auto start. I put little cubes iin and gel and handful of pellets. Ive tried blower on and off. Doesnt work. My xousin can light i. When blower on cold Ir comes out. Thanks forr tip😊omp ill try

[@DIYJIM]

Hope it works for you. Thanks for watching

[@robinolson8318]

What do you do once you have manually ignited your furnace? More specifically, do you have to press anymore buttons?

[@DIYJIM]

Nope just make sure you do not have it on auto light if you have it.

[@ossenaar]

I always have a spare ignitor on hand. They are not expensive and good insurance to have on hand. It is important to clean the area where the ignitor is located. Mine is behind a plate, locked with wingnuts, under the burn pot and I vacuum that area out carefully. My stove is plugged into a UPS power supply. In my area the power can go out, not always gracefully, during big snowstorms and I believe it can cause damage to the computer board and ignitor in the stove. After I have cleaned the burn pot, it always take a little bit longer for the pellets to light by the ignitor, I believe this is caused by the fact that there are no ashes in the pot that heats up quicker than all new pellets. If I have to light my stove manually, because I haven't swapped out the ignitor, then I use the same torch with mapp gas as you do. I do mix a little bit of whole pellets with ashes and throw it in the burn pot.

[@DIYJIM]

Thanks for watching

[@rick2853]

Five squirts of hand sanitizer and then the torch for me. Starts much faster than using the ignitor.

[@DIYJIM]

thanks for the tip

[@zedwpd]

Now show us how to run our stove when the power goes out.

[@DIYJIM]

This is all I got, kzbin.info/www/bejne/mZ2wmax4gNOdb6Msi=JDj57TlDrRszWuaX

[@whitechevy33]

Plug it into a tiny generator from harbor freight or northern tool.

[@Urban_hunter2021]

​@@whitechevy33 it needs to be a inverter generator or you can really mess up the internal motherboard in the stove. You need clean AC current from the inverter generator or from a pure sine power inverter.

[@whitechevy33]

@@Urban_hunter2021 yes in a perfect world but inverters are expensive and not everyone has one. I have a harbor freight predator regular non inverter generator, I have ran several fridges, and HVAC system during power outages they all have motherboards of some sort and I had no issues.

[@Urban_hunter2021]

@whitechevy33 Well, it always works until it fries it. I'm just giving you some advice.

[@RickB1792]

Hi Jim, good video. I have an Englander stove, 18 years old. The igniter failed the first season I had it and I've been doing exactly this to light it this since. Piece of cake. I use regular propane though, I'll have to try MAPP gas. I've also used a squirt of kerosene in the past and only needed to light it with the torch for an instant. That works well too.

[@DIYJIM]

Thanks for the tip and thanks for watching