How To | NAA Holster Grip Install

This tutorial shows how to install a folding grip on the Noth American Arms Mini Magnum revolver. naaminis.blogsp...

[@jameslogan6127]

Excellent video I couldn’t make heads nor tails of the instructions so your video is still helping people all these years later. Thanks very much I just installed this grip on my new Ranger II, Break-Top fits like a dream. 😊 thanks again I would never have figured it out without the video 🤦🏻‍♂️.

[@reggiepaulk]

You’re welcome! I can’t believe how long it’s been.

[@davidjphelps6201]

Great vid, so much better than paper directions ! Well spoken and very clear. Thanks very much !

[@theonlybp]

I'd like to commend OP on his video quality. This guy posted this video almost a decade ago and has it in HD. Most people from just a few years ago were using potatoes to shoot their videos with.

[@norsk129ify]

Great vid.!!!! thanks for the help. i read the directions but your vid helped me more than the directions could have.

[@gomcse]

This is the best installation video for this particular product. Thank you very much!

[@SkiRideWinterPark]

@AngelDecoys I've not shot the gun with the grip, but it's definitely easier to hold onto. You can consider it to be a full grip because there's enough room for all of your fingers, including your pinky. I'll have a follow up review video once I've put a couple hundred rounds through the gun with that grip.

[@averagejoe8255]

I’m really looking forward to your follow-up. Much obliged.

[@sauceLegs]

Hey I was hoping you'd show how to take the clip off at the end... cant get mine back over the catch. Thanks!

[@averagejoe8255]

Do think it would be a bad idea to store it with the grip folded up and over the trigger? I’m thinking the spring would compress over time, and lose effectiveness. I’d welcome your thoughts.

[@billburkhalter411]

The spring is not weak and it is designed to be kept in the closed position to guard the trigger. I hated the clip and removed it and filled the holes. Also removed some of the bulk near the trigger and made the allen screws flush with the grips now it is much easier to shoot and feels more natural.

[@bigvatodre]

Hi. The part you assumed is the part I'm having trouble with. What do you use to trim to fit the grip panels? Thank you.

[@erikjohnson9294]

Very descriptive and helpful. Thank you

[@edwardleonen1442]

Why your pistols don’t have a half moon sight?

[@kcline007]

According to NAA Tech. closed a holster grip on a mini revolver has a 3" height, open a 5" height

[@Theenemy38]

hey just a quick question hopefully you can answer it. I have the original NAA holster grips with my mini revolver and when I open the gun to use it wiggles just a little bit, my question is when you open the gun to use it with these grips does the gun wiggle or is it a solid?

[@papatriot9882]

Super helpful!

[@gdbunn]

how do you swap sides if you want to change the side of the clip????? THANKS

[@RWFinance]

HELP! Your video is the only one that plans to show how to remove clip but then you forget to show us! Can you walk me through it?

[@billburkhalter411]

Just remove the set screw and turn the clip 90 degrees to remove. Also you can over-tighten the axle its made from aluminum and I was trying to get the screws flush with the grip torqued it and axle became two pieces. The screw heads are supposed to stick out its designed to keep the clip from rotating.

[@SantaPlaysPickleball]

Can this grip be removed allowing you to go back to a standard grip if desired?

[@Guitargasm1000]

Yes. Do every step in reverse. Easy

[@jcmar209]

Thank you 👍🏼

[@SkiRideWinterPark]

No problem 👍

[@cemuka88]

Why not with coil spring in handgrip ? click-click ! open/close!

[@HerbalGoonWizard]

do you know if this grip fits on the NAA Mini Master?

[@robertarthur3532]

my sleeve snapped and I just barely made it snug