Perform Clutch Adjustment 9th Gen Honda Civic Si - Follow me on Instagram @559powerscape & on Facebook @Five59powerscape
Пікірлер: 97
@crazyhawkeye104 ай бұрын
3 years of dealing with the same problem. I wish I came here soon! Thanks man!
@559powerscape4 ай бұрын
Thank You, I'm glad this helped. Thank you for your Support!
@thomfournier39513 ай бұрын
thank you very much for this tip! i've had my car for 4 years and it's been 3 years that i've had this problem! I adjusted the whole thing and no more problems 👌 and now, it's been a week that no gears would go in after driving a bit! I'm glad I came across your video! Thanks a lot!
@559powerscapeАй бұрын
Heck yeah brotha im glad this helped! bet it feels good to drive it again!
@Life714life Жыл бұрын
Thank you very much I was just about to order a new clutch$ 1300 or even other transmission. That cost around $2500 and thanks to you video I solve my problem and save a bunch of 💰 again thank you.🙏👍🏽
@559powerscape Жыл бұрын
Heck yeah brother I'm Glad that fix the issue! I just made another update video on the same clutch adjustment cause 2 & 3rd were a no go on high revs.....and I rip it at the end lol Glad this fixed it bro 💪💪💪 Adjustment: kzbin.info/www/bejne/eJfEh2htrb2ofdE
@gregbrogee5641 Жыл бұрын
So glad I watched this, I thought it was my slave cylinders, clutch etc and my shop told me a new clutch but I just knew it wasn’t because it still engaged properly and never slipped. Now I don’t have to slam my clutch pedal to the floor just to hopefully get it in gear. Thank you for this video 💯
@559powerscape Жыл бұрын
Heck yeah brother, hope this takes care of it! Sometimes it just needs an adjustment and your good! Good luck brother!
@vsvpprettyflacko3 жыл бұрын
Thanks for this video bro 🙏🏼 I’ve been trying to figure out how to fix this on mine
@559powerscape3 жыл бұрын
Nice, hope this works out for you brother let me know if this works out for you 👍
@kyrdlmao22223 жыл бұрын
i just copped a new clutch kit for my fg4 now im like damn maybe i shouldve just tried adjusting it
@559powerscape3 жыл бұрын
Try adjusting it and save it for later
@PearlBlueSI2 жыл бұрын
thanks for the help, i installed a ktuned slave cyl and cmc and had a starter system and hill assist message pop up, turns out i need to adjust the clutch pedal free play
@559powerscape2 жыл бұрын
No way that's good to know thank you bro I appreciate the support!
@rollcam45063 жыл бұрын
I see you moving up. Stay on it bro
@559powerscape3 жыл бұрын
Thanx broskie 🙏
@balerchuy909 Жыл бұрын
In other words, longer rod higher clutch engagement.shorter the rod a lower clutch engagement.?
@559powerscape Жыл бұрын
yes sir!
@AndreiGrozea Жыл бұрын
A regular 12 wrench seems to fit in the Si, but there's no way to get it in there on the 9th gen 1.8 Sport, might have to cut the wrench in half to actually do the job. You're spinning the cylinder rod without removing the bit that holds it attached to the pedal, right?
@559powerscape Жыл бұрын
yup just move the rod to extend the clutch press
@user-mj8wz3wi7y6 ай бұрын
Thank you for the video. Adjust made!
@559powerscape6 ай бұрын
Thank you for your support, I'm Glad this helped!
@paulturner6692 жыл бұрын
Worked like a dream. Thanks!
@559powerscape2 жыл бұрын
Heck yeah bro I'm glad it worked out for you too! Thank you for your Support!
@Adam-vs4iw2 жыл бұрын
How did you even get to the pigtails on the sensor. I can't even see it. Lol
@559powerscape2 жыл бұрын
@@Adam-vs4iw u can try some needle nose pliers to help you out should be right on the opposite side of that pigtail
@Adam-vs4iw2 жыл бұрын
@@559powerscape thanks bro! You're awesome!
@559powerscape2 жыл бұрын
@@Adam-vs4iw thanx bro!
@thetruth7633 Жыл бұрын
Good info, does this fix the clunk noise when releasing the clutch pedal? Euro 9th gen, sure technical platform is the same. Motor mounts are OK.
@559powerscape Жыл бұрын
This helps with 2nd 3rd ger grinds and pop outs......I think what ur talking a about is when releasing the pedal it creaks right?....I've Sprayed wd40 on the cmc rod, press in the pedal spray it again , spray the clutch bracket and theirs a spring on it too...put a rag under the pedal to catch all the excessive wd40.....press in the clutch by hand back and forth and spray the rod again... This has helped with the creaks... and when it comes back repeat.
@bensnow48316 ай бұрын
So turning the rod clockwise towards the gas pedal will make the bite point higher?
@559powerscape6 ай бұрын
No thats making the rod shorter the longer it is the higher it is....the shorter it is, the shorter the grab is
@ekbenny39392 жыл бұрын
I feel like my clutch isn’t all the way out but I need this adjustment because it’s not grabbing and struggles to get into gears currently stranded lol
@559powerscape2 жыл бұрын
Yes. Bro try this see if this hopefully works...you have to play with it a couple of times till you get it where you want it
@dafb6dafb623 жыл бұрын
Ima have to do this to mine for sure
@managerialinitiatives Жыл бұрын
Thank you sir many blessings!
@559powerscape Жыл бұрын
Thank you! im glad you found this Useful, Thank you for your Support!
@kayden.k202 жыл бұрын
So clockwise right will make the rod go up or down?
@559powerscape2 жыл бұрын
Clockwise will make the rod go down into the CMC, counter clockwise we'll make it go up towards the clutch pedal. Making it go towards the clutch "longer" pushes more on the clutch to Disengage the flywheel...the less the less it disengages the flywheel.... You want to have the engagement point at least 2" when you come off the ground
@mrslapside6 ай бұрын
lol I’m still confused ima try to tinker with it this week
@vincentbeaulieu53003 ай бұрын
Thanks so much for the video !!! I just did this yesterday ! It was hot as fuck and now my back hurts 😂 however…. I didnt touch the 17mm nut or the clutch switch …. I only loosened the 12mm nut and adjusted the little rod for the clutch travel …. 100% solved my problem….. Do you think this is done on purpose from factory as programmed obsolescence ??? Because a lot of 8th and 9th gens have this problem of hard shifting or grinding and everybody always says its the clutch thats fried ?????
@559powerscapeАй бұрын
IM honestly not sure. I think its just wear on the clutch and needs to be re adjusted
@vincentbeaulieu5300Ай бұрын
@@559powerscape but wouldnt wear on the clutch make it slip, and not over engage ??
@Anonymous-ml3yn2 жыл бұрын
I'm having a problem ingaging first gear will this work for me please
@559powerscape2 жыл бұрын
It can possibly help, how far is you're clutch engagement? Is it as soon as you lift? Or does it grab up higher? It should grab about 1-2 inches after you lift so it can fully disengage the clutch
@dreamer8432 Жыл бұрын
What it sits at the same level as the brake pedal but there’s no resistance do I just need a new one?
@559powerscape Жыл бұрын
no pressure....sounds like the cmc and slave
@DeeferStratus4 ай бұрын
Dude, there is NO WAY that this will fix the issue of not going into gear! After searching all the forums, and contacting pro shops, only to be told that the clutch is out, even though there has never been an instance of slippage from it....... I'm attempting this now. Will follow up in a couple hours at most.....
@559powerscape4 ай бұрын
Hope this works!
@vincentbeaulieu53003 ай бұрын
I literally did this yesterday and fixed my problem…. Multiple people were telling me it wouldnt work and youre dead wrong…
@larrym46052 ай бұрын
Have you replaced slave cylinder? Had mine not shift at all like found or even put it in gear period without slamming it into the gear. Fixed with a stagers slave Cylinder. This adjustment will fix where the clutch hits on the petal not fix if it’ll change entire gears
@kevbravo1Ай бұрын
It makes it go into gear easier. This fix is for when you barely can slide it in
@FEARMonstrousityАй бұрын
Did it work??
@TheCoreyBritton10 ай бұрын
2013 civic si, clutch grabs almost completely at the top, can it be lowered by doing this the opposite way?
@559powerscape10 ай бұрын
Yes make sure the rod is extended all the way out and move the pedal back some....u have to play with it till you get it...but yes this will fix this
@xrzoom97912 ай бұрын
@@559powerscapeHow did you adjust the rod? For me it’s so hard especially at this angle. even with pliers. I was able to change the peddle height but not the bite point.
@user-ef3oz3ot4v2 ай бұрын
Thnx bud
@559powerscapeАй бұрын
Heck yes, im glad this helped! Thank you for your support!
@pablonator3000able2 жыл бұрын
Will this work with the Sirimoto CMC
@559powerscape2 жыл бұрын
Yes it should similar procedure
@pablonator3000able2 жыл бұрын
@@559powerscape Update: Yes I made adjustments same concept...I however lowered my pedal to have a comfortable dump, its all about what feels good on the ankle. Took it for a test run and instant satisfaction...there was no chance I would stall out on 1st as easy. Acuity shifter and bushings feel good also.
@559powerscape2 жыл бұрын
Heck yeah brother im glad that worked out. Yeah to were it feels better bro. Thanks for the update! Thank you for your Support 🙏
@orcahang215 ай бұрын
Good 👍 ASS job Brudda ✌.
@559powerscape4 ай бұрын
Thank you I'm Glad this was helpful, thank you for your support!
@al-1361 Жыл бұрын
Thanks
@559powerscape Жыл бұрын
Heck yeah brother glad this helped!
@aybowl1843 Жыл бұрын
I need my pedal lower and my cmc rod to be a bit longer, ima try this tomorrow see if it fixes my issue
@559powerscape Жыл бұрын
hope this works brotha
@revampmobilesolutions88518 ай бұрын
Did you have to disconnect cruise cable on top of that cylinder?
@559powerscape8 ай бұрын
Yes you might have to so it can spin freely
@revampmobilesolutions88518 ай бұрын
@@559powerscape looks like a pain lol
@dafb6dafb623 жыл бұрын
Now I know cuhhh 😊
@559powerscape3 жыл бұрын
Is Hella easy you just gotta play with it honestly till you get it we're you want it
@dafb6dafb623 жыл бұрын
@@559powerscape ima do it tonight💯🙏😎appreciate the video to
@559powerscape3 жыл бұрын
@@dafb6dafb62 hell yeah brother!
@dafb6dafb622 жыл бұрын
I found it 😆
@559powerscape2 жыл бұрын
🤣🤣🤣
@elcuh242418 күн бұрын
My Shi will not move
@559powerscape18 күн бұрын
Have you tried this already?
@elcuh242417 күн бұрын
@@559powerscape no no like my pushrod man , it’s not spinning
@elcuh242417 күн бұрын
My grab point is high but that’s also cause it’s a stage 1 clutch there known to be high I wanna lower a bit but it’s not spinning
@559powerscape17 күн бұрын
Try using some pliers
@elcuh242417 күн бұрын
@@559powerscapeI’ve tried it’s hard
@orcahang215 ай бұрын
God 💪 Bless 👊 Ukraine 🇺🇦
@559powerscape4 ай бұрын
Thank you I'm Glad this was helpful, thank you for your support!
@spoolypapii_si9 ай бұрын
what if the cmc rod is tight or is it that tight i just installed my hybrid cmc kit and it starts slipping
@559powerscape9 ай бұрын
It needs to be loosen....there's pressure being applied
@spoolypapii_si9 ай бұрын
@@559powerscape i used a small vise grip and clock wise the rod hoping it should fix the problem thanks for replying so fast🫡💯