www.slavensrac... Jeff Slavens explains how to do basic port clean-up on a KTM 250 XCW-TPI.
Пікірлер: 100
@user-dn5ok5fz1t2 ай бұрын
Thank you very much for showing us what you could. It's very generous of you to share your forty years of experience with us
@slaverace12 ай бұрын
It's my pleasure
@ponydown4186 жыл бұрын
Thanks for the info. I love that you share your years of experience with us and don't cup cake anything. You tell things exactly how it is.
@slaverace16 жыл бұрын
Cupcakes? I'm getting hungry.
@spotliterrr Жыл бұрын
Ok I have a question. I know the Ace cylinder is much smaller than the SR, so how different in port design are the 125’s? Thx
@byroneism Жыл бұрын
@@slaverace1 23
@TokyoOffroad6 жыл бұрын
Really interesting video. Thanks for sharing some of your porting knowledge and expertise.
@whiskeythrottleracing6 жыл бұрын
I love the brutal honesty.
@slaverace16 жыл бұрын
Thank you. I don't know anything else. Just an old farm boy from central Illinois.
@whiskeythrottleracing6 жыл бұрын
I find you very refreshing and intelligent. People like you are a precious commodity in today's world of liars, cheats, and thieves. Respect!
@brandongardner30733 жыл бұрын
Well if you love brutal honesty,this bloke will give it to you in no uncertain manner lol🤗
@eschrader2 жыл бұрын
"The use to look like someone left a cat turd in there or something" hahaha
@waynemodesitt34456 жыл бұрын
Thanks for this, and all your videos Jeff. Makes having a KTM just that much better.
@kfandrich6 жыл бұрын
Great video and very interesting. I’m still running a 300 kit you did just before you retired from porting and I have always been very pleased with the performance of it.
@yero73485 жыл бұрын
the best porting video I've seen ! great thanks from France
@markilleen40279 ай бұрын
here is a little tip for the sand paper if you get one of those little grinding disk bars you can put a few stacks of very fine sand paper and you get a really nice polish,
@chrisbillings3383 жыл бұрын
Giving my dude a thumbs-up and subscribe simply for keeping it real. Hard to find people that don't BS you nowadays.
@slaverace13 жыл бұрын
Thank you.
@bertietrust97555 жыл бұрын
love the fact that at 10:56 he says about being careful and having shaky hands and that he has 40 years of experience and then slips with the tool himself. its like ... Fair enough... i see your point ! :P
@schraubenschussel6 жыл бұрын
As a teenager, tuning my 50cc engine, i always wanted to learn how porting works. But never did it by myself - till last year. Got a cheap china cylindre and did some cleaning and minor changes to it before I installed it. Over the years I learned more and more about a 2 stroke engine, and how it physically works (still learning). So I just thought about how the engine runs and what could possibly make it run smoother or more efficent. After i installed the new topend i went on a little testride and even with bad jetting, the engine ran really good, and runs even better since it's jetted right. I owned a lot of scooters and modified each of them, so I got to know a few cylinders... I can't tell a big difference between original/racing 50ccs and the cheap one here, AFTER the "porting" (mostly "flowing"...). Btw: Really love the videos where you show something of your professional skills and experience. For me, this is the best way to learn things. :)
@blessedhellride26155 жыл бұрын
thank you,very helpful and informative, like the way you over emphasize caution,also liked your 5 best engine performance upgrades,.. big mike
@User-nb8mf Жыл бұрын
This is worthy of subscription.
@goinhot91335 жыл бұрын
Wouldn’t try this myself, but thanks for sharing the wisdom and knowledge!
@2strokecarbtuningportingin1873 жыл бұрын
Got the cc specialties porting tool with foot speed controller mine has to hang the motor don't have a base just say no to knife edjes
@officialnorde55844 жыл бұрын
Great video Thanks! gonna go ahead and polish up all my ports when it's time to change piston and rings!
@smokeyaallday6 жыл бұрын
I love my two stroke tuners handbook!!!!
@sethsc776 жыл бұрын
Thanks for sharing, Jeff. That was really cool to watch.
@slaverace16 жыл бұрын
You're welcome.
@littlewing606 жыл бұрын
Thanks for these videos jeff, I have never thought about porting and prob will never do it but the entertainment is great thanks.
@slaverace16 жыл бұрын
You're welcome.
@bermbuster63 жыл бұрын
Thanks for your professional opinion.
@slaverace13 жыл бұрын
You're welcome.
@clayhunt12846 жыл бұрын
Thanks mate .. next rebuild I'm gona give it a go ...
@Bigkidbird46 жыл бұрын
Good tips and explanations for what your doing 👍
@tyleravery443 жыл бұрын
Jeff did my 08 250SX head was a night and day difference.
@frankcrawford4165 жыл бұрын
I have a round stick or dowel I got from Home Depot that I cut a slot in to polish the ports with a drill and sandpaper.
@tinolino582 жыл бұрын
How about roughing up the inlet and transfers. Make shark skin.. it’s called little vortex generators in order to build a functioning surface layer of air to lower the general resistance of airflow. Some Honda riders do that with great success. It improves low end power. Tell us what YOU know about that technique please!
@closertothetruth92095 жыл бұрын
glad you made this video
@daverobins1822 жыл бұрын
just bought your 300 mule kit for my 09 xcw 250, so im kind of supprised that the piston is the same weights and its in balance
@mitchellkalina81914 жыл бұрын
Very nice video. I have a question on polishing the transfers, won't that cause the fuel to stick due to surface tension? I always thought you wanted a nice textured finish on the intake and transfers and polish on the exhaust but I'm not an engine builder like you. If this bike is TPI it would make sense to me to polish the bottom of the transfers like that as the fuel isn't introduced until up higher in the transfers closer to the port windows.
@slaverace14 жыл бұрын
I don't polish the transfers. They still have a rough texture.
@markmtbrider6 жыл бұрын
Very cool.makes me want to get another kdx and get busy.
@frankcrawford4165 жыл бұрын
Great porting tips.
@theroadjourney51956 жыл бұрын
Very interesting thank you! So did you recognize any major improvements after porting ?
@carlatamanczyk38915 жыл бұрын
I agree, Jeff.. I know too many do- it-yourselfers in the past that hacked up and worsened cylinders.
@bsmith4u22 жыл бұрын
Jeff, thanks for all you great videos. Does it help to go farther and match the base ports to the cases also?
@slaverace12 жыл бұрын
Not worth the hassle.
@montycrain57836 жыл бұрын
Very informative,precise and watchable. I remember reading that You used to raise the compression on the 300s I believe by decking the cylinder. Do you still think it’s a good idea? Also do you recommend any of the aftermarket heads with interchangeable combustion chambers.?
@schraubenschussel6 жыл бұрын
He uses a S3 Head on his bike, if i remember right. So I'd say he would recommend it :P
@slaverace16 жыл бұрын
Yes, I use the Slavens Mule S3 heads. slavensracing.com/shop/slavens-mule-high-compression-component-cylinder-head/
@adambatchelder41216 жыл бұрын
Great video, what thickness base gasket are you going to run when you put it back together? Also what is the minimum squish you like to see with your s3 head.
@slaverace16 жыл бұрын
.25 mm base gasket
@frankcrawford4165 жыл бұрын
What percent of the bore is the central exhaust Port window?
@enduro-parts-aus6 жыл бұрын
great video, very interesting to watch. cheers
@fowler17556 жыл бұрын
Do you feel there are much gains to be found by matching the case-cylinder transfers? I have found many to have 1/8-3/16" mismatch, not exclusive to KTM but also Yamaha, Suz, Honda...
@slaverace16 жыл бұрын
A lot of trouble for a very minor gain.
@fowler17556 жыл бұрын
Good to know! Thanks for the reply. Excellent vids btw...
@jeffreyhagelin3672 Жыл бұрын
Rotax engines already have base gaskets cut undersized from the factory for that reason.
@petersouthernboy63275 жыл бұрын
Can’t blame you for retiring from porting. It can be monotonous and hard on your back and butt staying in the same body position all day long
@ghostrider13965 жыл бұрын
So cool. Thank you👍🏻
@watchyMCFCwatchy5 жыл бұрын
Hi, what is that rotary tool you are using? Obviously, not a Dremmel with a flexi shaft.
@slaverace15 жыл бұрын
CC Specialty porting tool.
@spotliterrr2 жыл бұрын
I’m returning to the Hodaka hobby. Do you have any experience with the 125.
@slaverace1 Жыл бұрын
Yes, about 40 years ago.
@extec1014 жыл бұрын
how much in terms of horsepower does this type of cleaning up the ports do?
@slaverace14 жыл бұрын
KTM/HQV castings are very good so the gain is minimal.
@extec1014 жыл бұрын
@@slaverace1 its all the minimal things that come to make a god machine.
@timothyaiken97525 жыл бұрын
thanks for sharing.
@harm974 жыл бұрын
Stock is perfect,my opinion. Just ride it!
@jannep67724 жыл бұрын
But carefully cleaned up is even better. I did my Husky TE 250 2015 cylinder myself but I didn’t polish transfer ports. Just some clean up for the casting and polished exhaust etc. I have ported many cylinders but this video was good so I didn’t change port timing by altering port windows. I raised cylinder with 0.9 mm base gasket so this extends a bit transfer ports and exhaust ports duration. I have RK-Tek head, Wiseco 1-ring Racers Elite piston, Bill’s Pipes full exhaust, V-Force 4 reeds, Keihin PWK 38 carb with Suzuki RM NECJ needle and opened airbox as especially Husky’s are originally asthmatic... vs. KTM’s. I use red PV spring screw level with the case and a bit lighter main spring. This way PV opens sooner. This motor is just awesome!
@wesleybuck57254 жыл бұрын
Thank you for the info. Can the same process of just cleaning casting imperfections be used on other 2-strokes models as well? like YZ250, CR250, RM250 etc.
@slaverace14 жыл бұрын
Yes.
@wesleybuck57254 жыл бұрын
@@slaverace1 Thank you, would you recommend the same process on the intake?
@jeffreykrout30096 жыл бұрын
Thank you !
@jonjelen97556 жыл бұрын
Thank you for this video Jeff! Any other reading material you'd suggest for someone who's interested in 2-stroke tuning to take a look at? Also, what is your opinion on carb oval boring? Worth it for road use, or a waste of time?
@slaverace16 жыл бұрын
Two Stroke Tuner's Handbook by Gordon Jennings is the original bible on 2 strokes. It's out of print and expensive on Amazon.
@slaverace16 жыл бұрын
All types of carb boring add top-end performance but take away low-end grunt.
@enduro-parts-aus4 жыл бұрын
can really see how easy it would be to make a meal outta the cylinder !
@landmark49284 жыл бұрын
Help can you tell me I Have KTM 380 2002 The skirt broke Can I Put a 250 Cylinder What would you doAny advice would be appreciated
@rztrzt3 жыл бұрын
The crank, conrod & head also differs.
@Bidalotroxi4 жыл бұрын
You cant polish transfer ports
@thedaddydaughtersshow78294 жыл бұрын
Where can I get parts for 1982 XC 250 husky
@dickswaylo6 жыл бұрын
Hey Jeff, Im one of your dealers and can do this type of work, but if someone wanted more, who would you recommend? Pro circuit used to do all my stuff and it was great. Woods stuff is different though. Thanks!
@slaverace16 жыл бұрын
No idea.
@joebonanno2852 жыл бұрын
Any experience with bultaco astro 250cc cylinders/cases?
@slaverace12 жыл бұрын
Yes, about 50 years ago.
@joonatansaarinen12836 жыл бұрын
I would be scared to have that kind of bitt rigth nexto nicasil
@glennvandenberg39126 жыл бұрын
Hi Jeff great video. Would re-coating the nicasil remove the wear in the bore from the rings at TDC or is the coating so thin it won't fill those sort of imperfection.
@slaverace16 жыл бұрын
Re-plating brings the cylinders back to stock.
@lukerichards92532 жыл бұрын
Hi I’ve got a 1999 Ktm 300 exc/egs. I was wondering if you could port it for me please if I send you the cylinder many thanks
@slaverace12 жыл бұрын
Sorry, I retired from porting 10 years ago.
@joshfellows96013 жыл бұрын
You can take the casting flaws out of the ports that’s all I do
@byroneism Жыл бұрын
Have you had a chance to see kody kopp Head
@slaverace1 Жыл бұрын
I'm familiar with the flattrack racer but not a head.
@lombardozarateiii69206 жыл бұрын
Can i send you a cylinder to work on?
@slaverace16 жыл бұрын
Sorry, retired from porting.
@lombardozarateiii69206 жыл бұрын
Jeff Slavens 👌
@alancollard89394 жыл бұрын
you been doing this for forty years and you never made a fixture to hold the barrel ,one of the biggest no no,s is to knife edge port walls , there is a reason for this