How TO PROGRAM A BCM ... WITHOUT GOING TO THE DEALER

Body control module

[@petercosta3884]

Hello, I wanted to post my experience because a lot of people are coming down on you. So, this was my experience changing my BCM on my 2011 Chevy Impala. I purchased a used BCM, part number was correct. Took my lower dash apart and unplugged the 7 couplers that jack into the BCM. Then I placed the car key in the ignition and turned it on. Then I hot swapped the BCM by plugging in the couplers. As I did the lights on the dash came on. Then after all the couplers were plugged in, I started my car and as it ran all the lights on the dash came on, such as traction control, ABS, Stability Track error and so fourth. As the car ran, the lights turned off. I kept the car running for about 12 minutes. Turned it off because one of my concerns was the anti theft system. Everything worked fine, I checked it with my Tech 2 program, anti theft system was working, my FOB to open/lock doors, pop trunk, and auto start vehicle worked. The mileage carried over from the original mileage. Drove the vehicle for 50+ miles if any learning was needed. It actually worked, I have to say I was surprised. That was my experience, thank you for coming up with the idea.

[@ken_onsk8ts]

I have a 2006 lt shoudnt the part number be the same as your 2011

[@dwightlee6164]

you mean you turned your car off and then you replaced your BCM and it worked with your original car information without losing any infos. Right ?

[@petercosta3884]

@@dwightlee6164 The BCM needs to be hot swapped. Meaning when you are ready to plug the couplers into it, the ignition needs to be turned on.

[@erniecarrasco9107]

@@petercosta3884 did you turn on the car with the original bcm still connected? Then did you leave the car running while you hot swapped over to the used junkyard bcm? When did you disconnect the original bcm?

[@emmettturner9452]

@@petercosta3884 “hot swapped” would imply that the original was also disconnected in the same position, but that’s not what you describe. That’s just hot insertion. Did you mean to describe a hot swap?

[@jonklein5654]

I am an ASE certified mechanic. You are absolutely wrong. You didnt program a thing. You got a used BCM that was already programmed. Thats why the mileage is different. Thats the mileage of the car it came out of. NEW BCM comes from the factory WITH NO SOFTWARE AND MUST BE PROGRAMMED BY A CANBUS DUAL BAND PROGRAMMER. PLEASE STOP SPREADING BAD INFO CAUSE YOU KNOW ABSOLUTELY NOTHING ABOUT WHAT YOU ARE TALKING ABOUT. BTW CHANGING ANY ELECTRICAL COMPONENT WHILE THE BATTERY IS CONNECTED LET ALONE RUNNING... IS DANGEROUS AND CAN CAUSE MAJOR COMPONENT DAMAGE.

[@erichmmiiiable]

You are correct this was painful to watch

[@rogerd4559]

true but he has a working car now in stead of a pile of metal in his driveway

[@ArtificialDuality]

@@rogerd4559 He had a working car before, just not a working key fob. Now he has a working car, without a working key fob, and with the wrong mileage.

[@brianjones35]

Thanks. There's too many people that are clueless, and someone stranded sees propaganda like this , and have more probems than they had to begin with.

[@ftubbs107ft]

I am also an ASE master certified technician and you are so correct! He won't be happy until he sets an airbag off in his face

[@chris123church]

Although you didnt" program the BCM, you did change them out and the "new one" worked. Risky but Rewarding - Thanks for sharing sir

[@Seth______]

Thanks for the video, I totaled my 02 in an accident and bought another one for cheap with a bad bcm. I'm also scraping for money so this video saved me the headache of going to the dealer.

[@johnhiggins7894]

Mr. Harris Thank you for your thoughtfulness in providing a vido BCM and programming. As with many people who use this media, saving money on their car repairs to put food on the table is why I appreciate your knowledge and service so much. KEEP ON VIDEOING. Be Blessed.

[@alieyesonme247]

Bro, we don't need to see the engine or hear you talk about pointless things not pertaining to the topic of the video just show the BCM or what you think you know LOL

[@alieyesonme247]

Bro, we don't need to see you walking around the vehicle wasting time out of our lives just show the damn video about BCM

[@VideoVerseHQ]

Thank you sir for the wonderful info. You have saved me a huge headache .I wish more people in this world cared about helping others the way you Do. It would be a lot better place. Thank you., keep up the great work and God Bless .

[@fashionstreet1]

This video was priceless and thumbs up to you for this information im also a mechanic now i know how to reprogram a bcm! Thanks for this vital information

[@davidfarley6845]

Thank you Sir. I had been trying to find out how to program the BCM and doing it your way it worked great the lights on the dash came on when I started the car but they started going out as the car ran, It works great now Thank you again.

[@user-fe4uj5pl3m]

BCM it really Worked I have no power windows, no tail lights, no tag lights, no dash lights, i checked fuses are good even replaced main relay

[@mylifejourney74]

@@user-fe4uj5pl3m Dude, I have the same issue. I can't get a used BCM anywhere. Need a new one. But doesn't the BCM read from teh ECU and learn info? Or does it really need to be programmed?

[@larryfine4498]

You did not program that BCM. You simply transferred a used BCM to your vehicle. Your milage is incorrect and your vehicle security system locked up as a result. That used BCM has the restistance value learned from the vehicle it was removed from.

[@herby]

This video was a complete waste of time and should be removed. And you kept on saying you wanted to make the video quick. You failed twice.

[@altonrowell8137]

I noticed that to. He just changed out a bcm. He didn't program anything. The replacement bcm has the old information in it.

[@annie4oceans]

@@altonrowell8137 Even though this did not work on the used BCM he installed, he did provide the proper DIY procedure for reprogramming the BCM.

[@altonrowell8137]

So you are saying he programed the bcm. So why didn't it work. I replaced several bcm as a mechanic. I always used a tech 2 to reprogram them.

[@altonrowell8137]

@@annie4oceans are u a gm mechanic. I was for 35 years. I used a tech 2 to program the bcm. All he did was r and r a bcm.

[@buttfacemcghee]

Speed...............Ometer. Even though the fix didn’t work, I enjoyed watching and listening to Densel Warshingten.

[@globalcommunityaffairs6585]

Everyone has the option of taking the risk to swap out a used bcm or replace it with a new one. It's your choice. If it work great. If not go get a new one simple as that. Thanks for the info the dealers are not going to share it. And some mechanics will not either. Hmm

[@patrickpage3891]

What a pleasure it is to see someone who actually cares about other people thanks for the knowledge. P.Page

[@belongs_2_the_grave]

So leave the battery plugged up, and leave the key on (engine not running), remove the old BCM, install new BCM. Then start the vehicle. This is how it will program itself? Awesome!

[@alexcosme102]

Can you confirm this works? Also what vehicle have you done this on?

[@belongs_2_the_grave]

@Alex Cosme a shop plugged a donor BCM into my 04 Colorado, and it flashed my 98K mileage to 240K on my instrument cluster😑. So now I have to remove my cluster to have it zeroed out, and it will flash back to the correct mileage that my new programmed BCM is set to. This stored cluster mileage MAY NOT always be a issue with all vehicles. But I'd make certain before ever using a donor BCM

[@kendrickarchibald678]

I’m going to try this on an 03 Monte Carlo. I have a brand new bcm and I also have a donor bcm from a used car. Do you kno if I can use the brand new one or should I use the donor 1?

[@chevykent77]

@@kendrickarchibald678 did you try the bcm swap what happened?

[@user-pv4ml6td7s]

Thanks buddy, I've looked every where for this and of course it took someone from my hometown to help me out. Thank you brother...👍

[@glenninman428]

Thanks man so many videos in 2 weeks and yours was the only one that worked thank you

[@ezequielmartinez3455]

It is very helpful information specially when you live in tight life. Im talking about how we try to survive in Mexico, those repairs can reap you whole paycheck, awesome dude.

[@timclarey2648]

FROM A LICENCED REGISTERED MECHANIC AND GENERAL MOTORS ABOUT THE BCM "Remove and install a BCM body control module All repair procedures tell you to disconnect the battery cables first. Well, this time they mean it. NEVER disconnect or connect a BCM body control module with the battery cables connected. You can damage other electronic components connected to the sensitive data bus and you can even blow out the new parts. The hardest part of the job, aside from finding it, is figuring out how to remove the electrical connector locking latches. Once you figure that out, just remove the connectors and remove the BCM."

[@angelapruitt6307]

Thank you Tim Clarey, your post was extremely helpful except we seen your post after we watched & did what the video said (but would like to thank him for just being kind & trying to help people out he will be blessed). So did what video said, didnt work plus my security light came on & won't go out. Our problem from the beginning was our 2000 chevy S-10 WILL NOT START!! It's getting spark but no fuel, we have changed the fuel pump, fuel filter both brand new the pump IS working(you can hear it) so the fuel gets through the filter and that's it, stops there. Been working on this for a couple of months now we are completely frustrated at this point & can't keep putting $$ into thing's that aren't causing the problem were on social security so a very fixed income. Any help or thoughs that you can give would be greatly appreciated. P.S- the truck was running perfect then one day just wouldn't start. Thanks in advance, Angela

[@joedevitto6113]

I was wondering about that Tim .. i read up a lot on doing this. most said unplug the batter first thing , i need to replace mine and trying to figure out how to do it . also wondering if it will start up after i change the BCM.. since it wont start now , so i can get it to the dealer with out towing it..

[@joedevitto6113]

Tim question on buying a used BCM from Ebay that came out of a 2003 monte carlo. would that work if i just connected that in .. since its the same car it came out of as mine ? or does it still need to be reprogammed , not sure about the vin number or the miles reading would be affected , $40 is not a bad price if this would work , Thanks

[@rogerd4559]

on a chrysler minivan I think its easier to remove the engine as they hide the BCM behind the junction box below the steering columb. Then add insult to injury by putting unessesary bolts to attach it to theBACK if the Junction block. I was having two years of litghts that would quit at night, no horn, no brake lights, no instrument lights or instruments, no interior lights no wipers, no radio no windshield washers But it started up ok

[@772777777777777]

So how to correct the mileage for you vechical

[@MatthiasHamilton]

#1 this is great if you own a 2002 saturn Vue #2 You didn't "program" anything you just plugged the plugs into a different module #3 Whatever you did here didn't work... As a technician, i can happily say im glad you're not working on my car 😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧

[@rosemarie20]

I've got to change the BCM in my 2006 Pontiac Montana SV6. Thanks for telling me about turning the key on first. Also, thanks for pointing out the mileage change after swapping the BCM.

[@frazer9]

Did you succesful change the BCM using this method ....?

[@pattywelten4066]

I listen closely and boom it worked on my 2007 Suburban thank you

[@panzerwaffen2873]

I did really work?

[@richkar1127]

How did you get the security light to go out

[@ELEVOPR]

What every you do, DO NOT spill the Ice Tea 😜 I was told if you get a bcm with same part number you don't need to reprogram to your vehicle? Thanks for sharing, good stuff.

[@carmenperez-os5ku]

Thank you 🙏 works for my 2004 saturn vie !! The weell didn’t turn l did the same you said and work just fine again!!! It’s not complete 😊lm a woman and l did it!!!!! Thank so much

[@rogerd4559]

I tried it too and it worked

[@LegitLeeVelez]

@@rogerd4559 but didn't you just say no to do it because it was dangerous when you Commented earlier? So does it work?

[@rogerd4559]

@@LegitLeeVelez Yes I was saying its very risky, but I had no choice so I took the risk and it worked as he said it would

[@freddyg9026]

@@rogerd4559 Hows your face from that air bag explosion?..lol

[@MikeSmith-ed9ot]

Hey...thank you, man. You good ppl. I hope something wonderful and amazing happens for you and yours one day when it's needed. Be safe.

[@nathanmittower8261]

AWESOME nobody tells anyone these things without getting something for it thank you

[@rogerd4559]

I think id rather wait a day for the system to reset the risk damaging other delicate electronics on the vehicle. there are sellers on ebay that sell remanufactured BCM's for 250 and they will reprogram your BCM for free if you give your VIN number, year make and model of your vehicle

[@tedmoss]

Watch out for bait and switch scams, Fla company's are bad.

[@BrokenFox9]

I got a 04 ion 2 kinda havin same problem. The ion is known for ignition switches goin out pass lock coming on says service vehicle on dash board.. what I just found out is it’s not just the ignition it’s the bcm. Which led me to your video. My local dealership is a joke I’m not about to even think of taking the car there haha. I think a tech 2 scanner read all old codes from bcm, swap it out, reprogram should resolve everything. But what you did does help, on the ion’s it’s the same way you disconnect your battery and whole vehicle starts doin crazy stuff. My mom has a Chevy Colorado did same thing as well after disconnecting the battery. GM hmmm. Thanks tho man I’ll keep this info in mind if I’m fact it’s my bcm I haven’t pin pointed it yet.

[@JF-sv7qo]

I thought Denzel was narrating the video😂. Great video good info

[@dljunior2852]

This is ironic I run across this video. First, I have a BCM issue with my BMW 525i and it's needing replacing. Second, I have a son named Aaron Harris. He's an Aircraft Tech and I'm a retired Heavy Equipment Mechanic. I would like believe this would work on my wife's car but these cars have to many electronic modules (mess) and I have my doubts. Gotta do more research. Good job Sir.

[@woahdaniel]

This is great. My only question is, is it possible to keep your mileage, it seems like having inaccurate mileage would be annoying

[@carlschroeder3003]

The key fob is programmed to the bcm

[@alexcosme102]

Man pulled up his ebrake and said “why is my brake light on” but he’s a “mechanic” 😂

[@matt-matt461]

Ebreak doesnt cause the lights to turn on, its only activated with foot break

[@alexcosme102]

Matt-Matt ebrake does cause the light on the dash to come on that says brake to let you know one of 2 things. 1 your ebrake is on. 2. Your brake fluid is low

[@LetricShave]

@@alexcosme102 Matt Matt needs to get his head in the game.

[@panzerwaffen2873]

@@LetricShave to much crack cause that lol

[@gregschenk7665]

Put your original bcm back in, take your key fob apart. Clean the circuit board contacts with rubbing alcohol and a q-tip. Replace the battery if you haven't done that. Most times that will fix the key fob.

[@joedevitto6113]

Greg , what is a key fob ? what does it stand for .. i saw also on ebay you can buy these BCM that were in a car you have make sure you buy the right one for your same car.. would that just work without repraming you think ? since it was in the same monte carlo .. $40 they want for it 2003 Monte carlo BCM must of been pulled out of a junk car

[@rogerd4559]

exellent tip your a good man thank you

[@cliffjohnson3510]

Thank you! This also worked on a 2014 KIA Sorento!

[@bdolson5626]

Man I'm so glad I found your video I've been holding on to a bcm from a exact trick like mine been nervous about just swapping it out you just saved me a headache I would have had...going to do this in the morning....and your right I try to help people I see in need of help I'll still pull over to help someone on the roadside and don't ever ask for anything in return...thanks you

[@IM_AN_ALIEN]

So how did it work out? I bet it didn't. 😂

[@bletz5732]

Please retitle. Valuable Video. Just not for programming a BCM.

[@flatbrimsickdope2050]

"Don't never unplug-take your battery cables off.... Sorry man, but you shouldn't be giving advice on something you know so little about. All you did was a module swap, reprogramming requires a J2534 pass-thru device, or dealer scan tool. Many vehicles that are CAN bus equipped this advice will brick several modules, leaving you with a vehicle that won't start, and needing many modules, that need actual programming.

[@AlexR1ish]

Actually, modules are independent on a Can bus, for this exact purpose. If one breaks, the others remain intact.

[@jamesworsham2312]

Hey wake me up when we get to the real information. Fell asleep because it was short video

[@francisspaman2528]

Good info, which is pretty scarce on this subject. Thanks so much and keep the faith!

[@franklinyoung]

I sent my BCM off to get repaired they kept the same info on it just fixed the problems all for a 100 bucks and when I got it back just plug and play everything worked

[@ryannoriega7945]

Where did you send it ? I need mine repaired

[@franklinyoung]

​@@ryannoriega7945 you can find companies online where you can mail it off or you can find some local I did mines 4 years ago but what he's doing that's not programming it just happens to match that's why his is working

[@franklinyoung]

All he did was a swap

[@seanrobinson3368]

I had a retired police 2006 Impala. All I wanted was the dome light to come on when I open the door. I swapped the bcm with one I got from the junkyard. The dome light comes on when I opened the doors but now I have check engine light. The camshaft position sensor and no matter what I did it never went off. Including replacing sensor and erasing the code or even putting the original bcm back in. Also maybe you should have replaced the battery in your fob or reprogram it.

[@kenbarnett8189]

Thanks Aaron! This video demonstrated a lot of VERY valuable info, like where the mileage is stored and how to swap BCM's without going to the dealer! Like you said they don't make BCM's anymore, so our only real option is salvage yards, anyone that thinks your video isn't helpful is nuts, this will save me at least $150 bucks, I really appreciate your posting this!

[@cedricevans7193]

Did you have to get your bcm flashed or reprogrammed? I bout a used one....put it in and rode out. NO flash...reprogram or nothing. No Problems

[@joedevitto6113]

I found this place on line called auto parts warehouse i see a few they carry. i need to get one myself and was checking around $150 or so it says i have a 2003 Monte Carlo did you get your fixed Ken ?

[@rogerd4559]

but refurbish BCMs are all over Ebay cheap

[@jlcc9254]

Thank you Sir you video help me out Your idea worked for me my dash board lights up like a Christmas tree right now but it worked and got me rolling again..Thank you

[@xvidsionfiles8613]

I really appreciate this video!!! I'm going to try this method on my 2006 saturn vue.

[@codynewcomb9951]

Did It work

[@carlredenbach7223]

thank you mate, saved me money and time

[@papadronerlopez4433]

Love the narration, You sound just like Denzel Washington!

[@conor8321]

Haha ur right I feel like the rookie mechanic in training day now

[@chass5438]

I'm trying to get factory cruise control I added to my 2000 SL2 working. I'm a Saturn Forum member and get so many answers that a Swap is all I needed to have the cruise enabled. Did the swap, and now "No Start !" I believe it's a security issue and I also believe I was told wrong that this procedure works just swapping the BCM that was from a Donor W/Cruise option. O.K., If all of you Genius's out there that put other peoples comments down, how is this done then ?! If a lot of You know about car's so much and how this works, how do You enable the Cruise after all the parts are connected ?! Let's see how many of You can give the correct advice. The Forum states "IT CAN BE DONE !" Let Me know, then. We'll see. Most Dealers said they can't enable it because of the age, or say there's no guarantee it'll work, You pay the $135 either way. Lol, I don't think so. We'll see which way is correct, here.

[@jackparker8686]

I've heard enough... you record the cars when you're driving..... I believe everything you're saying from this point. .......you have passed my IQ litmus test

[@guillermocarrillo3253]

the title said programming , i said thas replacement

[@jpol3808]

You didn't program it you swapped it out with a junk yard part.lol Good programming.

[@rogerd4559]

this guy is a dangerous clown giving out misleading and risky information and risking injury from an exploding airbag or wiping out the engine control module, maybe the transmission control module and other sensors all to save 150 bucks? what was the original problem? his automatic door locks didnt work? god forbid some innocent viewer listens to this and an airbag takes his face off

[@frankpirson971]

And he said he's a mechanic , really ? You mean well but pass on facks not what you assume . Assuming is Dangerous !

[@jpol3808]

Jim halcom you are 100% correct sir! That guy shouldn't be making videos. He is endangering everyone who follows his bad advise to try to save a few bucks. Years ago I watched some air bag test videos and have since changed how I work on vehicles. I use a tool cart or magnetic tray under hood and never set things on the front fenders or radiator support to prevent dropping a tool and setting off a crash sensor. Also I will not move, test or disconnect any air bag connectors under the dash without consulting the repair manual to check the exact procedure on disconnecting that specific cars air bag system. I find so far the connectors are usually yellow and will have vibration locks on them. Those air bag videos show just how much damage air bags can do to people if they go off unexpectedly and your not fully sitting back in a driving position. Great comment. Thanks. Jpol.

[@rogerd4559]

Ever think about the consequences of accidentally setting off the airbag? Plugging in the BCM while the battery is hooked up can destroy the Engine control module, and set off the airbag. its like turning off your PC without properly shutting it down. I called my dealer and they told me another airbag and horn switch was 1800 bucks. So I faithfully disonnect the negative side of the battery before doing this work. a broken face and arms if you get in the way of an airbag can run you much higher then 450 plus 150 for programming

[@danperky4471]

The body control module has nothing to do with the srs system. The only way a deployment would happen is two of the three crash sensors went off. Air bag systems are robust.

[@AlexR1ish]

OK, we get you jimbo. You don't like this guy. It's best, when you say nothing at all, around other people. Bye the way, your info is wrong, too. You obviously don't understand airbag systems.

[@m998hmmwv7]

I know some dude that tried this dumb move. It added 85.000 miles to his car that had only 30.000.. now his resale value is garbage.

[@nolaward683]

hello! I tottaly agree my husband and I were just saying that people aren't like they used to be . Like if you'd see someone broken down you'd stop and help . Not now days ,but anyway thank you for the video it helped us.

[@DK-uq2yi]

Hey, That is not how to program the BCM. What you showed was how to get it to keep the theft deterrent and some other settings to remain in memory. These are called learns or relearns, not programming. Programming involves transferring the data from from the vehicle manufacturer site to the used module or transferring from one module to the other using an appropriate hardware devices and software. But your video non the less did show a method of how to swap a module, and keep your vehicle running without getting into key or theft system problems. At least it so appears on that particular vehicle. Definately worth trying and worth while. I am not sure but did your vehicle display the original mileage after or that from the used BCM ?

[@fatziotroll7695]

David Kellner firstly mileage is save on BCM . And then while you starting engine like these used BCM and turnoff , you can not restart by thieft detection. I am sure.

[@insideoutsideupsidedown2218]

Anyone know what to do when your keyless entry stops working in an 03 gmc sierra?...yes i changed the key fob and actually bought new ones...but i cant get into the programming mode...if i have to have the bcm changed and reprogrammed, ill just live without

[@MultiChevelle396]

Mileage is saved in both bcm and pcm

[@timclarey2648]

@@insideoutsideupsidedown2218 you need to take the fob and vehicle to be reprogramed to VIN

[@insideoutsideupsidedown2218]

tim clarey to the dealer?

[@michellegilday2114]

Aaron thank you I am ordering a BCM for my car a 2007 Suzuki Grand Vitara , it looks like I need to turn on the key during the disconnecting of the cables to the old BCM and reconnecting of the cables to the new BCM. Without turning off the key after it's replaced, I turn on the ignition? Just reinforcing what you have taught me. I enjoyed your video thank you for sharing.

[@thomasrose6962]

Well Michelle....Did i a used one work?

[@nonyabidnus5206]

You lying about being a technician. "Programming" is not swapping out a module. Thank you for wasting people's time.

[@jonathanmcnett8708]

What was the mileage on the other bcm? Is the mileage information stored in the bcm?

[@chass5438]

Nonya Bidnus: You're.

[@chass5438]

@@jonathanmcnett8708: Yep !

[@kimbalmccoy4892]

Thanks for the video on the body control module,

[@bboy327]

Thanks Aaron, great info! Kudos for sharing.

[@dustinyamchuk7400]

Wow you are a genius... would this work for 2008 cts??

[@clarkescustomcreations]

Sure stuff still works but you changed the miles on your vehicle and probably unlearned crankshaft position if you do that you will never know the actual mileage it has

[@MissChelseaLynn]

Thank you and also maybe somebody asked. My 2006 Cobalt. Has the ac controls with the plugs as well as the interior fuse box has the two plugs do I just do the ones plugged into my AC component? There are three separate plugs in that guy. But could see where I would possibly need to do the fuse box as well? Or just the three in the ac plugins? Sorry. But like you said. No money and so much work I've put into this car

[@e7414]

Video couldve been 2 minutes long or less just say at the beginning dont turn the car off when you swap the bcm just saved everyone 11 minutes

[@rancherokee2511]

"I'm gonna try to make the video as short as possible"

[@dawnmorris3372]

That's what I say!! I couldn't made it through the whole thing the first time I watched it!

[@mick00000000002]

Ok its the bcm the problem 100 percent. If remote don't work. ( try plug in and a couple of times. The relay will click in the bcm. And all will work. Another faulty bcm ( it come down to a relay in the bcm ( get a electrical engineer to change the relay. And it will work. God bless

[@dannys5395]

Aaron this is bad information. Not only did you NOT program it you have created many additional issues. Let me go through them. 1. Your mileage will change to whatever the used module had on it. 2. You will have the SIR airbag light on and it will not go off. It is programmed with the VIN supplied by the BCM and will NOT transfer as it will give you a configuration malfunction code. 3. Information on tire size is stored in it. If different than yours, your speedo will be off. You did nothing more than install a used BCM. These BCM specific to the Saturn car line are also a ONE TIME ONLY programming. To make this work you HAVE to have a new BCM that must be programmed with SPS/TechLine Connect. As to a no start with the security light on that is an easy fix w/o tools using the 30 minute relearn. In addition you will need to program you key fobs as they are part of the RCDL that communicates with the BCM and the FOB codes are stored in the BCM.

[@Wardy_AU]

WOW, that's 12 minutes I aint getting back

[@johnnywashburn5744]

Amen brother you are making this world a better place by sharing your knowledge and you are blessing others and you shall be blessed

[@IM_AN_ALIEN]

What are you talking about he didn't share shit

[@richardmiller3781]

I would think hot swapping a computer like this would create a short because of voltages issues. Sounds very dangerous.

[@francisspaman2528]

Thanks so much. Info on this subject is pretty scarce. God bless you.

[@vladimirbabayan85]

bravo, your genios, your best, tank you wery match for gold information

[@losvelasquez9071]

2003 envoy. I unplugged just how you said. Gauges never shut off. Plugged in the new one and still has the same miles. Wont start. Security light blinking

[@user-lu3fm1ex3u]

😂that really helped me out bro.Thanks alot

[@jeffgraham48]

clearly a rocket scientist! wow!!!

[@elconde0812]

Thanks man, reallly helpful

[@heathermichelle2703]

did you try a new battery in the key fob

[@zeke112964]

That would of been too easy! LMAO!

[@capturemediainc8763]

Aaron do you think this would work in a 2009 Nissan Rogue as well? The keys are working intermittently right now but my mechanic just told me that the BCM was the reason they weren't working consistently and that I had to take it to the dealer which want half as much as the thing is worth to replace and reprogram which is crazy. I'd appreciate a reply and thanks for your time.

[@josephfuller6930]

My truck has like 330,000 mi on it with a fresh motor so it'd be nice to if it reset it to a lower mileage. I'd be cool if that anyhow save on insurance

[@josejusino6171]

That was a great Video thanks for the good infomation

[@otgguy7282]

So turn the key to on position then swap the bcm and it's good to go? 2010 traverse won't even start because of the bcm going out and like most I can't afford $600 for a new one and to "flash" it. Really hope this works for me. Gonna order a used bcm from same yr/make/model and try this

[@justchillin7274]

Did you fix it? Have you looked up if your car has a way to reset the car anti theft lock/security light. ? If it has a step by step process then that might work. It worked for my car, since thats what needs to be synced. The ignition switch cannot communicate properly until it is reset, for my car it was a 30 minute process and a $30 part from the junkyard.

[@otgguy7282]

@@justchillin7274 no it didn't, I had to reprogram the key. Luckily my neighbors friend works for a repo company and they had the scan tool and let me use it. Took like 12 mins for it reprogram

[@gambler78415]

Thanks for the video on BCM

[@applepiebetty]

I do appreciate you trying to help others that have no idea where to start, but you really need to have a finished conclusion in order to sell your fix. Otherwise, you just come off as another person trying to get views. Someone in here does unplug the battery and puts it right back in, and the problem is solved temporarily, but perhaps if they waited 24 hours it would have stayed fixed. Their solution had not reached a finished conclusion either. Funny how haters in here can be so rude, yet they don't have the answer or even a guess.

[@rogerd4559]

But it WORKED!

[@alieyesonme247]

It's not a security problem though and your security light and ABS light and brake light are on because that BCM needs to be programmed correctly

[@RagtimeIrvin]

You kinda sound like Denzel Washington

[@rogerd4559]

but looks like OJ Simpson

[@carlospajuelo4797]

Thank you Sir; I'll gonna work on my 97 honda crv; I 've issues with door lock ,and internal light as well cigarrete lighter, ran some test on electrical shorts, but i think is the BNC. You mention the used bnc you replaced with , show the milage of the original car. My car only has 174,000 miles i should get something less than 200,000 right ?, I like your opinion.

[@javierflores1991]

Notice how the miles changed from 140k to 211k after he put the other bcm .

[@michianadroneservicesllc858]

I'm not seeing it. The mileage is incorrect with the new/used module and quite a few things are wrong including loss of communication with the key remote. Didn't seem like it programmed anything.

[@carmenperez-os5ku]

Plus l did get a new one l used the same one the car has!!! Thank you

[@altonrowell8137]

He's a parts changer. But I do appreciate his time.

[@chass5438]

Alton Rowell: O.K. Scanner.

[@boycotatlanta]

Thanks for the time for recording the video

[@rayleenmedina6403]

I will be trying this later today..fingers crossed 🤞🏼

[@mr.perfectto_u5300]

Did you try it?

[@edsmith6504]

Probably just have to reprogram BOTH of your key fobs, because it probably has to relearn the codes for those to work. There is a video on how to reprogram your own key fobs for free in your driveway in 5 minutes, or take it to a locksmith and they can do it for far less than a dealership, or take it to a dealership where they will gladly steal your money with a smile on their face.

[@TSWARD-xb9rk]

Thanks brother. Traitors make the world worse. You are correct.

[@chengluo3826]

what if I put back my old BCM in case some thing goes wrong with the swapped BCM. Will It still go back working with my original BCM? Thanks in advance for your answer.

[@pimpinallstar917]

Yes you can always switch to the original bcm

[@edwardosu]

Thank you. I will try it on my 2001 saturn sl2. It's a different kind of car but it may work on my 01 saturn sl2.

[@kenmiller4376]

Thank you very much

[@stevenkelble5248]

good job bro

[@tedmoss]

This isn't magic, you don't have to take off both battery cables, just one, make it the negative for safer operation.

[@BrettGlass]

Wonder if this would work on other GM BCMs. I've been looking for the location of my RCDLR on a 2002 Escalade, but no one will tell me where it is or if it too needs to be programed???

[@lucristianx]

This video someone doing a book report on a book they didn’t read.

[@jamesphillippe3653]

Thanks for the info on my BCM. As you described the problem it is exactly what is happening to my 2001 L300 Saturn. And thank you for how to replace it and reprogram it. However, did the used bcm still have the program from the previous vehicle? Thanks from Jim of Roseburg Oregon

[@wrapthenews8496]

Did u ever fix your problem

[@wrapthenews8496]

My Saturn l300 2001 miles are Unknown as well

[@mylifejourney74]

Would this work for a new BCM that has never been programmed?

[@eddiemejia6942]

Yo dope video my brother.... Wife heard this video in background and she was tripping. “Did Denzel working on Saturn?”. I said what...? Denzel? Props. You do sound like Denzel.

[@RogerHammonds]

Eddie Mejia my girl said the same thing lol

[@rogerd4559]

and acts like OJ simpson