How to protect lowrider motors from burning up so fast

[@mooremaceo]

Loooong winded! But still appreciate the homie for taking his time to show us this!💪🏽

[@giovannogalindo8785]

appreciate you giving out these cheat codes to extend the life of motors definitely going on the to do list keep them coming homie

[@axelled.diaz-maldonado8541]

Preciate Ur puttin dis out here. Need more people eduk8n riders worldwide. Stay blessed

[@trentarbeau8753]

Thank you sir for sharing any information and knowledge on the motors. Much appreciated, and thanks for sharing the build of the motors, and how to do it properly.

[@BIGCHIEF305]

Thank you for sharing bro you saving people money and keeping lowlows in the streets ✊🏼🙌🏼🙏🏽

[@willieurus]

Great video makes sense everything u did

[@eliudlopeztexas]

Bomb videos, bless your knowledge for sharing to lowrider fans 🙏🏼

[@raychavez8711]

Thumbs up you homeboy for your skills and your knowledge well appreciated I myself am working on a 64 Impala 66 Impala then I'm down to my grandkids again I appreciate your knowledge

[@alonsonavarro2126]

I had a monte Carlo with 2 pumps for 10 years with the same motors, never had to change them. Your just creating more heat in them with what your doing bro.

[@Cen805coasT]

U clearly never hit the switch then lmfao

[@alonsonavarro2126]

@@Cen805coasT rookie it's ok I understand when you don't know. You "clearly" don't know.

[@trustnobody1281]

We coat the bottom of the brush plate to make it thicker but never put jb on the armature or the case. I would have to say that it most likely gets hot at least on a high voltage hopper. Maybe this is ok on a street car idk

[@willieurus]

@@trustnobody1281 I agree on the brush assembly yes but not on anything else but to each his own they will learn

[@pepperiv5652]

This video was definitely worth sharing. Good stuff Homie 👊🏽

[@Banditemcee123]

So i did this to some new motors i put them in the whip hit the switches and they didnt work...not sure what i did wrong...put the old ones back in until i figure what i messed up 😂

[@richf5759]

Thanks 4 the video Homie much needed ..LOWRIDER LIFE..$$

[@blown93vert93]

Varnish

[@Johnsondidit]

Great video, I'm glad to have watched this.

[@tboneo2005]

Yass love your vids man salute 97 cutty needs work let me know

[@anthonymaestas4863]

Thanks

[@MisterLowrider]

Low lows and more: Good video!! I'm having an issue with my lowrider. It goes up on the right rear corner but won't come back down. I do have a burned out switch that controls the right rear corner along with its own pump. I also bought a magnetic dump solenoid, and it burned out too. It gets hot as soon as you hook the magnetic solenoid up. Do you know what that might be? I have videos of my S10 on my channel so you can see my setup if you need to.

[@giovannogalindo8785]

Hey bro I had a similar issue on the front where the driver side wouldn't come down and it turned out to be one of the dump wires came loose from a but connector so for peace of mind I replaced all them with the heatshrinkable ones hope this helps

[@MisterLowrider]

@@giovannogalindo8785 oh ok cool. Imma try that. I got 4 pumps so each one has its own, so I'll check the wiring. Thanks man!

[@mikesnipes316]

You can disconnect the dump wire and touch it to 24v to see if the dump will drop. If it does, it's most likely a bad switch. If it doesn't drop, it could be a bad dump coil. Had same issue and replace dump coil.

[@MisterLowrider]

@@mikesnipes316 thanks man!! I'll try that!!

[@adriangallardo05]

Can lock tight tape be used for the rods that hold the motor?

[@lowlowsandmore]

You can if you can get it on, using shrink tubing is easier.

[@freddierodriguez7741]

I bought a brand-new motor and less than a month it messed up it had a little coating on it on the copper all that melted when they got burnt up is it still savable or is it done can I JB welded it and try to make it work

[@freddierodriguez7741]

I got a question do I j.b weld it before I break it in or do I break it in and then j.b weld

[@MonicaRodriguez-hm8xw]

Do you have a video on how to break in the motor

[@lowlowsandmore]

To break in a new motor before installing it, hook it up to a battery for 12v(some people use 2 batts to break them in) by using jumper cables and let it spin for 30 seconds to 1 min straight and it's ready to install onto the pump.

[@tjsilvius1]

Pro tip good looking out 👍

[@fernandoh.2609]

What’s the JB weld for ? And why do you put it on ?

[@Tre0bama_]

Hey man what is a good gauge wire for battery connecting?

[@lowlowsandmore]

Use zero gauge, most common one is 1/0 gauge

[@jamesgiles79]

What's the best oil to run In pumps. 0w 20 Full synthetic?

[@nobodyschild967]

Non Detergent if u have access 👍🏽

[@refugiolopez6194]

Cool vid bro.

[@josebeltran702]

How did that rear end turn out? The final product

[@lowlowsandmore]

It came out great, it's my buddy's ride now.

[@soulessm8015]

THIS THAT KNOWLEDGE SHIT! NOT CACA! THANKS .😷🇲🇽👏👍💪 no secrets in this lowrider relationship . NO HOMO! 😷👍

[@HA-rz5rj]

Lock tape can I just use black electrical tape

[@lowlowsandmore]

This hold better than electrical tape, you could also use liquid electrical tape

[@miguelmaldonado9881]

Sorry to say, but all this is unnecessary.

[@AllHail_PHARAOH]

Why is that? if you do not mind expanding your opinion/knowledge

[@jaredhays3331]

What do you think about converting a 1964 bel-air 2 door post car into a impala... What's your advice

[@mathewmaldonado3570]

What's up homie

[@quintyrob]

Hi how can I contact you privately

[@lowlowsandmore]

Email or through Instagram

[@greyclassic6563]

Seems pretty toxic but worth a try lol