How to R154 Sc300 In 10 min

As weI’ll know our buddy Alex SC300 with the 1.5 JZ was completed a few weeks back and unfortunately we did not have enough time to convert the car to our r154 just due to time his car was an original manual w58 car So we go ahead and get the new set up in the car and give you a quick test drive to show gearing differences. Between both transmissions it appears that you gain about 500 RPM lower and final drive enjoy

[@turbogears900]

Love SC life ❤

[@Squireissocoolie]

Sick build!

[@alexfleming4281]

Now im ready to setup antilag

[@danthomas86]

Hi, I own a IS300 NA-T with a manual swap. In Europe we can use the J160 box out the IS200. Relatively cheap boxes but don't handle too much power. I'm running an unopened vvti motor at present but intend to swap in a non vvti bottom and crank it up... Do you recommend the R154 for the IS300??

[@SidewaysPerformance]

Yes 100% We love the r154 transmission

[@nickkingkeo3707]

Great video. I appreciate the upload. I'm thinking about doing a manual swap from auto to manual in an 05 is300. Will the r154 transmission fit perfectly in the center console or will I have to make a hole to compensate for it?

[@BrandonBuiltVideos]

if it’s not the tripod trans u can just buy the shifter extension and it’ll fit

[@jomarsierra2516]

Hi I have a question about a 1995 sc 300 the I can swap out 1997 sc 300 it will work or not if not what be the best way to go thank you Joe

[@SidewaysPerformance]

I don’t get ur ??!

[@jomarsierra2516]

@@SidewaysPerformance sorry for miss righting the ecu for the 97 SC 300 it will work on the 95 SC 300 or what is the best way to go thank you for your response joe

[@stevenedwards4269]

What is the cost to do a automatic to r154 swap at your shop?

[@Jursaw]

If I wanted to do a manual swap in my 2002 IS300, where is the best place to buy a clutch pedal and brake pedal and R154 trans?

[@brahdislloyd]

What did you do about the Speedo? My speedo currently doesn't work.

[@jameswagner4721]

What year is the sc and what length should the extension be for a factory manual car

[@turbogears900]

Or the can get a tripod R154 from jzx100

[@SidewaysPerformance]

Correct we have them in stock new was well he just got a killer deal on a Mk3 r154 so we went that way

[@turbogears900]

Great I just installed 1 in my sc300 with a 2jzgte vvti

[@TLCHobbies]

5:40 ... I think this is helpful. I think my factory W58 is on its way out and I don't want to put another W58 into my 93. I would like to put a brand new R154 and I know it won't be a easy bolt on without some modification. Would I have to do any other modifications? Like hammer out the transmission tunnel?

[@2JRaz]

No, the SC300s were sold in japan as Soarers and the 1JZ-GTE Variants had the R154 Transmission from factory. As far as I know, no hammering is required. My only concern would be Driveshaft fitment.

[@TheHighroller88]

just ordered a jzx100 r154 from drift motion with a mk3 shifter housing $3.250.00 . i had a w58 strapped to a 2jz-nat non-vvti running 20psi of boost gtx3584rs in a 87 Toyota supra 2 years later and the w58 let go hard third gear gone

[@SidewaysPerformance]

Damn 2 bad u payed that much man I could have gotten u a way better deal

[@mario2jz]

does the r154 work with the stock driveshaft in the sc?

[@JoeWitAFro]

Mixing the driveshafts comes up with one that is too long by a small margin. To run it with the proper depth into the yolk it will need to be modified, and at that point 1 piece is better.

[@DavisNguyen-uu6lm]

Hi what was your measurements for your 1 piece drive shaft? Need to order one as well for my r154 in sc300