How to rebuild a Honda distributor

[@axmadrigal1]

good video but I would have changed the bearing too while you're in there

[@CorpseFreak]

Will keep that in mind for in the future

[@tsheposenong9081]

Hello guys any information on how to solve no spark problem on this distributor. The coil was in bad shape I replace it then I notice that the igniter is not igniting the coil what could be the problem coz even on the injeter wires I don't get signal but only power??

[@CorpseFreak]

@@tsheposenong9081 that could be an ECU issue

[@tsheposenong9081]

@CorpseFreak ohk thanks will check it 🤝

[@kenelder9615]

use a very good philips or japanese JIS to unscrew the rotor cap, it can be on very tight

[@CorpseFreak]

I need a good JIS honestly

[@jom7796]

(whisper) that’s what she said. Lmao that was funnyRandom!

[@CorpseFreak]

She liked it too

[@thanhdang2546]

Is there a camshaft position sensor inside the distributor? Thanks in advance.

[@CorpseFreak]

@@thanhdang2546 yes

[@wkboyy4573]

hey so I accidentally snapped the dog ear on the drive dog and want to replace it and I see that you marked the orientation to put it back on but I was wondering how I could make sure I have the correct orientation on a completely new drive dog that im going to replace the old one with? thank you in advance

[@CorpseFreak]

If you put it on backwards the car won't start. I don't really have a great way to tell you man. I'm just a dude making videos sometimes I'm not a shop or anything.

[@sniper7269]

If still needed, the way you do it is you point the rotor (or flat side of the rotor rod) in the direction of the first cylinder (if you rotate distributor so it's round on top and two corners down and cap side facing you, it's towards the left corner) and then you put your drive dog so that its and distributor's grooves are on the same side and should line up.

[@harveyyork8370]

Nice work bro

[@leorivera1372]

There should only be one washer when pulling out the pin? Mine had a lot of play, side to side when moving it so i thought it needed 2 washers?

[@CorpseFreak]

This was an untouched dizzy. 1 from factory.

[@leorivera1372]

@@CorpseFreak okay thanks was trying to find out where the leak was

[@leorivera1372]

@@CorpseFreak sorry for the question, had to ask since I opened a distributor on a accord and it had 2

[@CorpseFreak]

@@leorivera1372 no worries man! Every dizzy I have ever seen has been one. Haven't touched many accords though I'm actually working on fixing a hacked together obd1 to OBD2 ecu right now

[@DatJere]

GREAT VIDEO ! QUESTION: has the shaft some movement like axial o radial?

[@CorpseFreak]

A tiny bit of shaft play

[@SG901]

HELLO: can i ask whats the meaning off the spring you put back in the coil: ,mine dit not have the spring and i put another spring in there: is it possible that without the spring the coil not fire* greetz from belgium

[@CorpseFreak]

Yes. Spring is Needed for fire. It's closes the gap from coil to cap.

[@SG901]

Ok thank you for the information. Greetz geert

[@marilynmelendez8256]

What if you clean all the seals could it work?

[@CorpseFreak]

@@marilynmelendez8256 no. It will still leak.

[@808breaks]

Will the ignition coil you have in the link as the JHD500 fit and work on a 99 civic obd2 B distributor?

[@CorpseFreak]

Just saw this. Let me take a look

[@CorpseFreak]

If you have a 99 SI Which I think the Engine is the B16 then the ignition coil OEM part number is 30510-PT2-006 which is on the link I posted. you can find oem part numbers at hondapartsnow-dot-com

[@DadTimes]

Hi! Great video! Is this for a ‘95 civic dx ej2? Thank u!

[@CorpseFreak]

@@DadTimes it would work for any d or b series.

[@DadTimes]

@@CorpseFreak thank you!

[@SauceLyo]

At 8:22 how donyou know you didnt put it 180 off does it matter ?

[@CorpseFreak]

5:37

[@ivanr5436]

What can i do if the pin doesn't slide out? Its stuck in there but your video and others it just gently slides out

[@CorpseFreak]

Did you take the lock ring off?

[@ivanr5436]

I did. The pin is loose on the outer key but somehow stuck towards the center of the shaft. I tried lightly tapping but nothing

[@h.m4612]

You know very well

[@CorpseFreak]

lol

[@dekonfrost7]

Called engineering

[@CorpseFreak]

lol

[@malemex2002]

Sloppy

[@CorpseFreak]

Glad you enjoyed it!

[@joseordonez3422]

The cuestion is is go a work becouse i have replace the coils the ingniter several other things and it stil don work for yoy tb crerible you need to put it on car and started

[@CorpseFreak]

@@joseordonez3422 I have no idea what you just said lol. It is on my car though and I use it Everytime I drive the car. Also other people had success with my video. This sounds like user error to me my guy