How to rebuild a Yamaha warrior 350 cylinder and head from start to finish.

[@AlPass-w3q]

Just bought a carb off ya ,very pleased with the product ,runs great.the fact that you use the actual jetting for the warrior is awesome 👍

[@zoomzoompartsllc]

Thank you for your support

[@conoverkid8221]

This is the best video I've seen on warrior rebuilds great content!

[@zoomzoompartsllc]

thank you so much hopefully others find it helpful as well

[@mxbeanz1206]

Elevator music needs to go though xD. Tough to hear what you're saying in some parts

[@cletusbowling923]

You all really need to do a full engine build . Bottom end top end and transmission. Full build. So we cam see both sides of inside the cases and transmission crank and so on. Plus a valve system and cam.

[@zoomzoompartsllc]

we did do the cam and valve system in this build as for the bottom end we could probably do a small video on it as i have one i am going to be opening.

[@mxbeanz1206]

Thanks guys. love the content

[@AirOnTheMove]

Great video very informative

[@zoomzoompartsllc]

Ty bro

[@cartsquads47]

Is this the same engine on the raptor 350?.

[@zoomzoompartsllc]

yes there was a few changes but nothing you would see aside of the carb

[@evanlance1426]

For the ring end gaps what should they be?

[@geegonebadoin]

I have a question. What is the valve clearance set at?

[@Evadingmoto]

Does the connection rod wrist pin bushing spin?? Or is it stationary?

[@berad187]

What was the measurements for the valve lash adjustment for Both sides I'm been new installing new rocker and Rocker arm shafts on my 2002 Yamaha warrior 350

[@zoomzoompartsllc]

if you are using a stock cam i go with 0.08 in and 0.18ex but always check with repair manual

[@zachwhyte6040]

Does this kit come with the valves already installed in the head? Or is that the head that y'all took off the engine?

[@zoomzoompartsllc]

The head we sell dose not have valves or rockers in it

[@Kevin-is-here]

Thanks for sharing 👍🏼

[@keithnelson7919]

Why did the valve covers need to come off and can you explain what you were doing at the very of the end of the video with the flat metal tool (I don’t know what it’s called)

[@zoomzoompartsllc]

Feeler gages have to set the gap on the valves

[@mxbeanz1206]

Are you using a oem cylinder head or aftermarket? Was always iffy on the aftermarket heads for the warrior.

[@zoomzoompartsllc]

We used are forged kit we have it in all are warriors

[@oscar9737]

Is that dude’s voice really like that or is he faking an accent lol

[@zoomzoompartsllc]

that's richards voice and accent 100%

[@michaelpresey2273]

What are those 2 allen bolts for bellow the cam cover ? As I'm taking mine apart the one wasn't even tight

[@zoomzoompartsllc]

Part number 91317-08050-00 they hold your gasket head and block all in line till you get the main head bolts in

[@michaelpresey2273]

@zoomzoompartsllc thanks for quick reply !

[@rcclassiccrawlers4368]

How much valve lash is there supposed to be?

[@zoomzoompartsllc]

Would depend on your cam but with stock cam I go 0.18mm and 0.08mm

[@ericm3836]

Is the .08mm in the front or the back?

[@SethGranger]

No lock tight?

[@tylerschultz3298]

What about bottom end? I think my noise is rod bearing

[@zoomzoompartsllc]

we did show a open bottom end in one of the videos but had no reason to open this on you can check your crank and rod bearing without taking it apart. if that checks out it could be a counter balancer bearing and that would have to be torn down

[@1991tommygun]

The shitty music ruins it