How to Rebuild an EZGO Robin 295/350 Engine

Both the 295 and 350 Robin engine builds are the same. In this video we show in detail the rebuild process. Contact us for any rebuilds or any parts or help you may need.
Our Shipping Address for engines is; 3505 Figsboro Road - Martinsville, Va. 24112
www.ecartparts.com/re
www.ecartparts.com/gas-parts-...
www.ecartparts.com/connecting...
#ezgo #golfcart #golfcartengine
#robinengine #enginerebuild #enginerepair

[@kennethmays6830]

Great job. Thank You for taking the time out of your day to make this video. I know it’s time consuming to do. My son has a channel…aMAYSing metal works. He builds muscle car bodies for a living and it takes a lot longer to do when filming.

[@woodwerkman1]

Thank you for the tips tricks and information

[@Railtech_63.]

Thank you so 3,very helpful and great information.

[@crystalsink6887]

Great video! Very informative 👏

[@user-qe2ep7ne4w]

Thanks for your videos I am trying to rebuild 2 engines.

[@iRideiRide]

great video. nice and to the point. no extra babbling. thank you.

[@rans471]

That was a great video. I may be calling you

[@KEJRacing]

Jason hell of a Video buddy

[@patsector7g723]

Good Video ! Thanks !!!!

[@cartsmarttv]

Thanks for watching!

[@superochosvwcorner4782]

I’m wondering since you build ezgo motors can you put the 350cc rebuild kit with pistons and valves on a 295cc motor like the one your building on your video. thanks

[@cartsmarttv]

Crazy enough we will be having a video about that coming up. You do have to have your block bored for the 350 piston and maybe even decked? We have block at machine shop now. Thanks for watching, we'll be in touch.

[@mydustyguitar3855]

Looks good. Next time lets port the head and drop a cam in it....😁

[@danielrollins5897]

Great video. Do you know if the internals from a 350cc MCI engine are compatible with a 350cc pre MCI engine? I am having troubles finding a full kit for a pre MCI 350cc.

[@cartsmarttv]

The internals are the same for both engines. Thanks for watching.

[@toothpick61]

Can you give a little more detail about installing the cam shaft. And the oiling ports in the valve cover and why the cam doesn't have bushings or bearings. My timing belt broke because the cam seized

[@cartsmarttv]

Not sure why Robin designed them like that? Sounds like you didn't have enough oil coming up into the valve cover to properly oil it for sure. Might need to blow air into the side (hole) to be sure the oil is coming up through there. It should come up through there by just turning the motor over with the cover being off.

[@justintroy9827]

I just bought a 94 ezgo that I was told was a 00 and was also told it only needed a carb clean. I was got good, the right side piston is seized. Oddly, I test drove the cart and it ran just poorly but sounded great. Making me believe it needed just a carb. So I’m going to need to rebuild mine. I assume I’ll need to hone out the cylinder? Where’s a good place to go for a rebuild kit? Thank you sir.

[@cartsmarttv]

Sorry to hear that, we'd love for you to give us a call for what you need. Our parts are proven and use on every rebuild, it's some sketchy stuff out there on ebay and Amazon so watch those. Plus we help with any tech call unlike others. Give us a call and we'll hook you up with our stuff. 276.632.8905

[@emersonschneider796]

Boa tarde estou a procura de 2 bielas dessa que fundiu vc teria uma site pra me indicar que eu possa estar comprando.

[@cartsmarttv]

www.ecartparts.com/connecting-rod-e-z-go-4-cycle-91-mci

[@schuck9326]

Very good video, lots of useful info. Didn't see you replace the connecting rod bearings. Does this engine have rod bearings?

[@cartsmarttv]

Thank you, they do not have rod bearings in these motors which sometimes causes problems for sure. If they get hot and low oil the rod will seize to the crank and break. That happens quite often.

[@schuck9326]

@@cartsmarttv I would think on air cooled engines it would be more critical to have bearings. I remember my air compressor rod doesn't have bearings either. I'm guessing the two of them are not under tremendous amounts of load so it probably doesn't matter too much.

[@bowhunter4893]

Did you go back with standard sized rings after rehoning the cylinders?

[@cartsmarttv]

On this one we did as it had standard pistons in it. If they have been oversized it would be stamped on top of the piston.

[@just_in_time5518]

Great how to video! Is the primary clutch bolt reverse thread?

[@cartsmarttv]

Thanks for watching, No the threads are normal counter clockwise off and clockwise on.

[@masonmandelkow5852]

What's the tool you used to clean the top of the block with? And what's the foaming degreaser you used?

[@cartsmarttv]

We use a 1/4" angle grinder with Scotch Brite pads and just any engine degreaser.

[@user-jg9el9xy8b]

Hey man so I rebuilt the top end on one and we’ve been trying to figure out why it won’t start come to find out both pistons are at top dead center what the easiest way to get them correct?

[@cartsmarttv]

That is correct as both are on the same stroke. Be sure you have your timing set right. Check out this video... kzbin.info/www/bejne/noW8p4qkjqp2r7csi=1WEFE2rD-q5P78f9

[@tinobalestrini1886]

I have a 295cc that needs a rebuild I’ve looked online for rebuild kits, my question is I see these kits just seem like top end of the motor no new crank. Since I’m going to have the motor redone should I also buy a new crank and put it in so I don’t have any issues?? I just want to make sure I do it correctly. Any tips or advice in this situation? Thank you very much for your help

[@cartsmarttv]

In over 25 years of rebuilding these motors I've never had to replace a crank so you should be good. If it was running before you should be OK with rings and valves. Be careful on your parts though as this week alone I've had several calls about some stuff that was brought on Amazon... all of our parts have been proven to be good stuff for over the whole time I've been rebuilding these motors. Not trying for this to be a sales plug but we're here to help after the sell unlike the others or Amazon.. family owned and operated. Our parts are in the description or feel free to call us at 276.632.8905 Thanks for watching!

[@tinobalestrini1886]

@@cartsmarttv I so appreciate your help in this situation gives me peace of mind will definitely be looking at ordering parts from you in the future thanks again

[@steveandrews8301]

Can too low off a compression reading on cylinders cause an EZGO TXT gas cart to stop running after a few minutes of running and being warmed up? I'm working on one for a neighbor of mine whose has hard starting issues and also cuts off / loses power, just won't go when it warms up. The cylinder pressures are low on it - around 60 psi., is this what is causing this to happen? The spark does look very dim, to me, visually, on it, too. Could these symptoms just be due to a weak coil / CDI unit on it, or is it more likely a compression / weak motor issue? What would you recommend I do? Thanks.

[@cartsmarttv]

It could cause a problem as it gets warmer, coils can really cause a problem once hot. Anything under 100 is a problem definitely a hard start issue, could be the valves also. You could try to put a little oil in the cylinder and test to see if compression changes must to test if it's getting by the rings. Feel free to give us a call to go over anything. 276.632.8905

[@steveandrews8301]

@@cartsmarttv Thank yo so much!

[@jordandunbar6951]

What kind of assembly lube do you use? Just standard oil?

[@cartsmarttv]

Yes, just standard 30 weigh.

[@larrysmith1134]

Are the aftermarket rebuild kits any good? Or best to use all oem?

[@cartsmarttv]

They are some out there we don't trust or have had customers tell us about them mainly from amazon. What we use is in the description, it is aftermarket but a trusted brand we've been using for years. For 10% off use code ECP10 at checkout.

[@davidroach6984]

I have oil coming from behind the timing cover. Would this be a bad balance shaft seal?

[@cartsmarttv]

It's very possible? That's one of those need to pull the motor and remove cover to see?

[@martycofield4588]

are all the rebuild kits the same quality, or is the a certain name to look for? Great video!!!

[@cartsmarttv]

We all pretty much sell the same stuff for all the carts. The difference between us and them is we're here to help after the sell and a real person answers the phone and can help with any questions. (we're family owned and operated) Let us know if we can help. Once you find out what you need, check here..> www.ecartparts.com/re

[@skippydippydoo49]

So when i line up the 2 dots on counterbalance with the single on crank the rod ends hit the counterbalance

[@cartsmarttv]

We have ran across this issue before. You could have a mismatched set of Crank and balance shaft. I think one or the other may be from a 295? And other 350? You can make it work as long as your keyway is pointing up on the timing side then put your balance shaft in, your dots won’t match up but, doesn’t matter at that point long as you’re not touching.

[@skippydippydoo49]

@@cartsmarttv thanks ill try it

[@saltymethods2637]

Great video! Do the 295 and 350 engines use the same rebuild kits?

[@cartsmarttv]

Pretty much so less the piston/rings, the rest is the same. Let us know if we can help. Thanks for watching!

[@sexymanshaun]

Did you replace the valves, or just clean them up?

[@cartsmarttv]

That was the problem with this motor so, yes we installed new valves and new rings in this one. Thanks for watching.

[@jeffwakeland-246]

Where can I get the bearings for the E-Z-Go golf cart motor

[@cartsmarttv]

Which bearing (s) are you needing? Here are some > www.ecartparts.com/bearings-seals-2 - Give us a call with details. 276.632.8905

[@chxcwells]

What size socket is required to take off the fan?

[@cartsmarttv]

Sorry for the delay. It takes a (1 3/16") socket. Thanks for watching.

[@chxcwells]

@@cartsmarttv thanks! Great video. This will definitely help

[@codyrheiner]

What size hone do you use for this?

[@cartsmarttv]

Gearwrench - 2487D - 3-3/4" Engine Cylinder Flex-Hone

[@kennethcoble269]

my ec350 runs great but smokes .where are you located and for this build what was the cost?

[@cartsmarttv]

We're in Martinsville, VA. We video the whole process once we receive the engine, open to see what's wrong, call with cost to fix. 276.632.8905

[@kennethcoble269]

@@cartsmarttv Martinsville isn't far . I'm close to Winston Salem. What's your turn around ?

[@kennethcoble269]

@@cartsmarttv any special tool needed to replace valve stem sealer ?

[@cartsmarttv]

@@kennethcoble269 on most cases within the week.

[@cartsmarttv]

@@kennethcoble269 not for valve seals. They just pop off and back on.

[@dexterlong9389]

I'm sorry to bother you, but I'm burning out coils once a week. On my Robins to 295 golf cart and I'm Buying.. Chinese, is that a bad thing?

[@cartsmarttv]

That almost has to be a bad part(s) deal. It's a on going problem with some things sold on amazon??

[@dexterlong9389]

@@cartsmarttv Can I purchase one through you?

[@cartsmarttv]

@@dexterlong9389 www.mygolfcartshop.com/csearch.aspx?Search=coil&CategoryID=0&ManufacturerID=0&SectionID=0&PriceRange=0&SortBy=1&PageSize=12&AndOr=AND Let us know if we can help. 276.632.8905

[@travisschoepke4787]

So the shiny ring goes in the middle??

[@cartsmarttv]

no, We put that one on the top.

[@billwestlake2544]

What's the price of rebuild on the 295?

[@cartsmarttv]

Anywhere from 300 to 900. When shipped to us we video the whole unpacking to the break down of the engine and inspect everything and then send the video to you with an estimate of the repair to be ok'd by you. We get several each week. Let us know if we can help.

[@kenwillis8487]

Where are y’all located? I’m thinking of sending you my engine for rebuild!

[@cartsmarttv]

Martinsville, Virginia

[@kenwillis8487]

It was great talking with y’all! I look forward to talking on Monday after I run some tests!

[@QMB3]

what would it cost me to have you do this? I take care of shipping.

[@cartsmarttv]

This one ran approx. $700 but Give us a call to go over your issues. 276.632.8905

[@duaneb2545]

How long did it take you?

[@cartsmarttv]

It takes us about 2 hours for rebuild once out of the cart.

[@duaneb2545]

@@cartsmarttv which is better; ball hone or glaze breaker? I do have one size over jugs….your thoughts please

[@cartsmarttv]

@@duaneb2545 we like the ball type. Works well for any size hole.

[@donjoncas5572]

my engine has no compression what would be the cause and would rebuilding take care of it thx Don great Video

[@cartsmarttv]

@@donjoncas5572 Hi Don, It could be several things starting with the valves then the rings worn. We're getting a couple per week if you don't want to mess with it or can help you any way we can. 276.632.8905

[@crazedgoldminner7384]

Tell something you may not know the engine is manufactured by the same did people that bring you Harley-Davidson engines and it's a really good engine if you scoot the seat forward reach down in there and bypass the governor they'll do 4550 mph on a city street I know I used to work for work form is a mechanic

[@markcorriher4718]

O yall swap out motors ez 295

[@blowme5150]

Love how you skip all the important steps

[@cartsmarttv]

Tell us what they are?

[@dontnoaname6]

Then they can't get you to buy their service

[@cartsmarttv]

@@dontnoaname6 what does that mean?

[@AS-fm6iw]

Easy go is absolute garbage