EZGO TXT 295cc Robin Engine Tear Down (EH-29C)

[@armedfarm3429]

Good job on the video. On the filters, they sell em on e-bay, along with air filters & a bunch of other parts. I am doing my valve guide seals this week, so yer video was timely.

[@NINEPOINTFIVEPROJECTS]

Hi thanks for watching and the comments. Good info on the filters, thanks! Also I think you may have already but if not please consider Subscribing and hitting the like button. I would really appreciate it.

[@Jaymc63b]

Thank you for doing this! I’ve pulled my motor and wasn’t sure how to remove the clutch so that is a big help. Also there are so many little parts on this motor that the way you have documented your rebuild is gonna be a huge help putting it back together. My cart went out in a cloud of smoke! I feel like I broke a ring. Thanks again.

[@NINEPOINTFIVEPROJECTS]

Hi thanks for watching and the comments. Glad it will be helpful for you! Let me know when you get it back together and how it runs. I think you may have already but if not please consider Subscribing and hitting the like button I would really appreciate it!

[@johnisbell9220]

The white wire goes to the oil pressure switch, not all carts have them, but you could connect a light to is so when you lose oil pressure the light comes on. I like how you show the bolts as you pull them out, I take photos.

[@NINEPOINTFIVEPROJECTS]

Good idea 💡

[@mrblanche]

The hot tip on removing the driving clutch is to fill the center hole with grease and then run in a bolt. The pressure pops it off.

[@NINEPOINTFIVEPROJECTS]

Hi thanks for watching and the comments. Yeah, I used oil and it worked pretty well too. You may have already but if not please consider Subscribing and hitting the like button. Thank you !

[@Gus_1991]

Awesome video. Thanks so much!

[@NINEPOINTFIVEPROJECTS]

Hi and thanks for watching and the comments. I also have a rebuilding video on the engine that may be helpful as well. Either way I appreciate you watching. Also if you haven’t done so already please consider subscribing. It would help me a lot!

[@Gus_1991]

@@NINEPOINTFIVEPROJECTS already subscribed and have been watching your other video! Thanks again!!

[@Jaymc63b]

People bash WD-40 but it works. It wouldn’t be so huge if it didn’t. Plus I’ve seen it work myself so many times.

[@NINEPOINTFIVEPROJECTS]

.

[@KJMarchelak]

Top job and willing to have a go for sure !

[@NINEPOINTFIVEPROJECTS]

Hi and thanks for watching and the comments. Yeah the whole process is not that bad. I have 2 other videos on the engine, one removing it and one rebuilding it. Check those out as well. You may have already but if not please consider subscribing and hitting the like button. Thanks again.

[@johnisbell9220]

Great Job!

[@NINEPOINTFIVEPROJECTS]

Thanks John

[@johnisbell9220]

The front aluminum engine mount has a throttle control bracket (black steel), that bracket makes it difficult to remove the engine from the cart, I put those bolts in the opposite direction when reassembling, head of the bolt now faces the front of the cart and the nuts are between the bracket and engine, with the bolts in that direction you can remove the entire throttle and governor linkage by removing 4 bolts.

[@NINEPOINTFIVEPROJECTS]

Good idea!

[@sparklingcityservices]

I see you left a comment down below about a link to the rebuild kit in the description, but I do not see it.

[@NINEPOINTFIVEPROJECTS]

You know, you're right! I just now went and fixed that! Thanks for watching and the comments. Please consider Subscribing and hitting the like button if you haven't done so already. Thanks again.

[@sparklingcityservices]

@@NINEPOINTFIVEPROJECTS Subscribed! What engine oil do you use in this motor?

[@NINEPOINTFIVEPROJECTS]

I used 10w30. I think I saw that listed as a requirement somewhere. You might better google and double check me on this on. Thanks for Subscribing!

[@pauldowns9880]

Do you have a torque spec for the bolt that attaches the drive clutch to the crank shaft? Thanks

[@NINEPOINTFIVEPROJECTS]

Hi and thanks for watching and the comments.. I'll have to look and I'm not to where I can do that at the moment. I'll get it for you as soon as possible.

[@NINEPOINTFIVEPROJECTS]

Hi Pauldowns9880, Sorry for the late response and you probably already have your question answered. I do not have torque specs for the drive clutch bolt. I looked on line and didn't find the answer either. To be honest, I think I just tightened it about as tight as I could get it with a foot long ratchet. It's a large fine thread bolt and I wasn't too concerned with striping it out the way I did it. Let me know how your rebuild goes (or has gone).

[@KJMarchelak]

Do you know where to get a coil pack for the same engine - same as mine- txt 1996 ezgo

[@NINEPOINTFIVEPROJECTS]

Hi, thanks for watching and the comments. I would think you could probably find it one on ebay? Let me know how your rebuild works out and don’t make the same mistake I did regarding the timing marks on the belt pulley. I think you may have already but if not please consider subscribing and hitting the like button.

[@jim1connie2you]

Ez go tear down

[@NINEPOINTFIVEPROJECTS]

Hi thanks for watching and the comments. If you haven't done so already please consider Subscribing. I would really appreciate it.

[@emersonschneider796]

Onde posso encontrar motor desse pra comprar completo

[@NINEPOINTFIVEPROJECTS]

no hablar

[@mitchelltassin2368]

Where can I buy parts for robin 295cc for ez cart

[@NINEPOINTFIVEPROJECTS]

I bought mine on eBay. There is a link in the description. Thanks for watching and the comments. If you haven't done so already, please consider Subscribing and hitting the like button. I really appreciate it. Also let me know how your rebuild goes.

[@CatKen-gq1ec]

It was manufactured by Harley-Davidson

[@NINEPOINTFIVEPROJECTS]

Hi thanks for watching and the comments. I've read your other posts and that's some interesting information. I can't imagine going 55 MPH on this thing. That would be a little intense. Either way I think you may have already but if not please consider subscribing. I would really appreciate it.

[@johnisbell9220]

All keyways face up when timing, the dot actually is about 4 o'clock when timed correct.

[@NINEPOINTFIVEPROJECTS]

Yeah that dot threw me off...I should have known better. Live and learn...

[@leosweeney7955]

Water, for the hydraulic pressure, much less messy!!

[@NINEPOINTFIVEPROJECTS]

Hi, thanks for watching and the comments. I'm not sure water would have worked. Have you done it with water? Either way if you haven't done so already please consider Subscribing and hitting the like button. I really appreciate each and every subscriber as I continue to try and grow my channel. Thanks again!

[@Jimmyd_Rocktalk]

Awesome video!! Thanks

[@NINEPOINTFIVEPROJECTS]

Hi thanks for watching and the comments. Glad the video was helpful for you. I think you may have already but if not please consider Subscribing and hitting the like button. I would really appreciate it! Thanks again.