living life on the edge. no rags in the bottom end when installing the circlips
@danbee64074 жыл бұрын
Lmfao
@nicholasmazzone33862 жыл бұрын
Lmaooooo No cap
@dansavka76482 жыл бұрын
Not needed when u got magnets or you can just say eff it and throw more at it.. rule of thumb Do not drop more than two circlips in the crankcase really should be fine 🤣🤣🤣🤣
@chipper2035 жыл бұрын
Great video, I would recommend measuring with a bore gauge instead of the telescoping gauges. More accurate and less room for operator error.
@stvnmoto5 жыл бұрын
I would have definitely preferred using the dial bore gauge, but RMATV didn't have one so we went this route, and most guys don't have one either. RMATV wants most videos to be portrayed as a simple, easy, task for the guy in doing it at home. I however would do this rebuild a bit different.
@PRODIGY1231002 жыл бұрын
Bro thank you, this video was amazing, I got my banshee up and running in no time, can't thank you enough! - Phx, AZ
@sambo65912 жыл бұрын
Did you buy this kit from them how is it holding up
@TerpyToaster5 жыл бұрын
what a beautiful well kept machine
@rungassamydonovan475 жыл бұрын
2 stroke again! This is amazing!
@shaunmurray81324 жыл бұрын
this video was done extremely well. I used it as a bible when I built mine. great job!
@rmatvmc4 жыл бұрын
Awesome, glad it helped you out! Thank you for using our video!
@thelonerider83895 жыл бұрын
Yep off with the OEM cylinders on With the China cylinders and piston 👍👌
@quattro44684 жыл бұрын
Isnt your phone made in china?
@thelonerider83894 жыл бұрын
@@quattro4468 yeah probably lol but that does not compared to a banshee 110$ top end kit cast shit pistons The port timing is all messed up on those cylinders Normally the cage bearing on the wrist pin end is completely junk normally don’t last a ride. They are no different to eBay or the Amazon cheap kits you get what you pay for junk
@thelonerider83894 жыл бұрын
Especially if you ride your bike extremely hard the kit won’t last a month. Just like the Yamaha blaster kits you’ll be surprised if you make it on fire up. You spend the money in your bike will last long
@SuperNestafari5 жыл бұрын
Better than Texas banshee? No way...good job guys
@dustintobler98404 жыл бұрын
Used this kit on my bike twice. Can only get 90psi after fresh rebuild. Make sure u go with wiseco pistons
@SuzukiQuadLife3 жыл бұрын
What about the jugs
@LandonMartien3 жыл бұрын
Wiseco is the best worth the money
@Ham_Strokers_Ejacula4 жыл бұрын
A pair of sockets (one to push and one as a cup) and a c clamp works just the same to get the wrist pins out
@the_ltz_guymaster79125 жыл бұрын
Can u do a video on shock adjustment
@kylemcbride65532 жыл бұрын
Wondering if you put a gasket on both sides of the reed valve?
@tylersoutherland79055 жыл бұрын
You guys should do a Yamaha warrior rebuild
@rmatvmc5 жыл бұрын
Be careful what you wish for!!
@orivera2152 жыл бұрын
What brand torque wrench is that ?
@705motorlife5 жыл бұрын
Hey love the video! Do you have a link to your torque wrenchs that go in low ft lbs like 0-30 or sumthing like that?
@dirtbikedudeministry64302 жыл бұрын
Inch pounds wrench then convert
@connerhooper20835 жыл бұрын
We didn’t get to see the test ride ;(
@desertduneslakeandlife253 жыл бұрын
Used this kit but upgraded to prox pistons (personal preference)
@Alexvd004 Жыл бұрын
hi group can i install rd350 machine in banshee complete with rd 350 install thanks in advance
@rmatvmc Жыл бұрын
Hello, sorry I'm not exactly sure what you're asking.
@cbr600rrturbo5 жыл бұрын
Need trx250r vids to please
@قناةلقمان555 жыл бұрын
I need banshee
@c199754 жыл бұрын
what would cause rings to break up. this is the reason i need a rebuild kit but i am wondering why this happened
@rmatvmc4 жыл бұрын
The piston rings breaking is most likely caused from overheating and detonation (spark knock).
@danielmaksimenko14945 жыл бұрын
How often do they have to be rebuilt?
@rmatvmc5 жыл бұрын
It will really vary on what kind of riding you do and how well the Banshee is maintained. If you're racing it'll probably need rebuilt around 20 hours but if you're just messing around on the weekends the top end might last 60+ hours.
@dunerider45055 жыл бұрын
Hey I’ve seen those q&a cylinders on your website and they are pretty cheap. That’s what worries me, I have a lot of money into my banshee so would you guys recommend these that they are pretty good quality or should I stay away.
@rmatvmc5 жыл бұрын
We've installed these on a stock banshee and it runs great. We'll actually have a video coming shortly showing us riding it. We haven't put a ton of hours on it, but initial impressions are really good! Just be sure to follow the recommended torque specs when putting it together.
@dunerider45055 жыл бұрын
Rocky Mountain ATV MC hey thanks for the reply I’ll keep an eye out for the vid
@stevencarter32904 жыл бұрын
@@dunerider4505 personally i wouldn't go with those cylinders. If you have the factory ones send those out and have them bored to the next appropriate size and ported if the budget allows.
@FranciscoUrrutiaolguin Жыл бұрын
Where r u Located?
@rmatvmc Жыл бұрын
Our main headquarters is located in Payson, Utah.
@clementelara36075 жыл бұрын
Is good!!
@gabrielalvarez95708 ай бұрын
That engine would never pass a leakdown test, I hope that the pistons you used were ProX
@rmatvmc8 ай бұрын
We used the Vertex Piston kit in this video: www.rockymountainatvmc.com/parts/vertex-stroker-piston-kit-p
@chefboiard54685 жыл бұрын
Can anybody tell me why its ok to leave the gas on people tring to get clogged carbs?
@darrenarnold73615 жыл бұрын
Hi all Iv got a kxf250 on a 08 the problem I’m having is it keeps back fires does anyone one know what it could be
@JonnyDisilva-z065 жыл бұрын
Darren Arnold clean the carbs and put a new spark plug
@crunkdaddy115 жыл бұрын
needs the valves adjusted without a doubt
@kvrfilms50085 жыл бұрын
Ignition issues or it need a valve job
@BostonBanshee2 жыл бұрын
So on a stock banshee you can’t just put wise on pistons in? Wouldn’t 64mm fit perfect for squish ?
@rmatvmc2 жыл бұрын
You can certainly put Wiseco pistons in a stock Yamaha Banshee. We have many sizes of Wiseco pistons available for the Banshee. You can check those out here: www.rockymountainatvmc.com/parts/wiseco-piston-kit-p
@BostonBanshee2 жыл бұрын
Thank you very much I purchase all my parts from you guys!
@Angel.Garcia15 жыл бұрын
random bike to do it on, but i like it🖒
@Lewiseyers5 жыл бұрын
It's not random, it's a iconic bike, possibly the best quad ever made
@upstatefilms50345 жыл бұрын
Not reliability wise lol
@ME-wq8lq5 жыл бұрын
And I thought I could this myself
@mathemacits24005 жыл бұрын
So we gotta find out the perimeter of the cylinder head to see if its spec like area and perimeter of shapes?
@rmatvmc5 жыл бұрын
To see if your cylinder head is in spec all you should have to do is measure the head with a straight edge and feeler gauges, you can see us doing that starting at 6:32 in this video. Hope that helps!
@mathemacits24005 жыл бұрын
@@rmatvmc yea it did thanks👏
@FrederickEnse25 күн бұрын
I need this so bad i need help banshee folks
@Mark-RD350 Жыл бұрын
If you don't already know all this then you shouldn't take the engine apart, an if you're Rod is a funny colour you should go to your Dr. an get some cream for it an apply as directed 😂
@Alrisi3255 жыл бұрын
What about breaking the bike
@luisbravo43355 жыл бұрын
Where’s the trx 250r rebuild videos?
@dr.hugog.hackenbush94435 жыл бұрын
LOL! The engine design has been around for over 50 years. If they dont have it down by now.. 😆
@wbcong2 жыл бұрын
you never synced your carbs
@rmatvmc2 жыл бұрын
We have a separate video on syncing Banshee carbs. You can check that out here: kzbin.info/www/bejne/e2W9dHdojJaMaKc