Yamaha Banshee Bottom End Rebuild | Part 3: Assembly

[@danw9946]

The best part of a banshee! Cases split top to bottom and you can do them in about 30 mins!! Man I’m going to buy another banshee again. Literally looking at some now. Thanks Rocky Mountain and I mean that in a good way!

[@patpan007]

Generous, accurate and excellent information in a super well organized environment. Thanks a lot !

[@dennisleach5815]

The reason I brought it up is I just bought a banshee because I wanted to fool around with my son and his friends for myself. I bought one for myself and the guy I bought it from sold to me cheap but I realize when I got there that he was a flyby KNIGHT mechanic so I bought a whole rebuild kit to rebuild the bike and then I was watching your video to put it back together and was following directions and when you said I’m putting on the clutch basket you did that and then said oh you have to put on a thick washer, then the sleeve, then the clutch basket, but you were already done I was done also and that’s when I realized that this dude that was a real piece of work that I bought the bike from. He must’ve lost the washers because I just disassembled it. There was no washer behind the clutch basket. There was no washer in front of the clutch basket. All there was was the retaining clip, but I almost put it back together like that.

[@danellsworth3891]

Absolutely fantastic video well done sir thank you very much

[@Maskinteknikk]

Great video

[@hectorramos8039]

Good job friend 🙌🙌

[@robertsheehanii8096]

You guys are pretty awesome.

[@ismaelibarra441]

Great quality video

[@joselinopinto7979]

Well done brother

[@mikebates8420]

Great video thanks!

[@Dieselpower0804]

Makes it look soo easy. Awesome

[@traviswagner9114]

Nice video! You made it look easy enough that I can do it.

[@dominiquelawrence1502]

Pddndnd

[@TECH-NOTICXs]

Do you guys sell this kit for the banshee all parts

[@martimcocco3422]

is the hot rods crank reliable?

[@Saikly-239]

How do you set the timing?

[@dennisleach5815]

Oh, and by the way, what is the inside of the conical washer? How are they supposed to know what’s the differences?

[@rmatvmc]

Conical washers have one concave side and one convex side. Place these washers so that the raised center part is raised (concave side is down). So that when you tighten the bolt, the washer gets flattened.

[@stanleyrobinson15]

No engine leak down test ?,?

[@WestHaddnin]

00:26 bro how tf?! I could not make it slide on for the life of me! I ended up damaging a crankseal trying to install it.

[@Jweiss7939]

I see that folks only put the half circlip on the bottom when installing the crankshaft. Is that all that goes in there? Is there another half for the top case??

[@rmatvmc]

It does seem a little weird but yes, all that's needed is the retaining clip that goes in the bottom half of the case. Thanks for watching!

[@dennisleach5815]

And sorry, but there’s a lot of people out there that go off of image so when I was following your lead, I’m a mechanic on hot rods on cars I was following your lead. I already had the basket everything installed locknut on everything and then realized when I replayed the double check that you didn’t show them putting the washer on

[@trailblogger]

EXCELLENT

[@devinmadrid3158]

Man this guys a bad ass

[@tim140i8]

i just replaced my my Idler gear bushing on my banshee, but now the idler gear fits really tight around the axle.. is this normal? thank you

[@Peeweebuilt559]

Bad ass dude

[@user-kc1qk7hv1y]

Hello, what kind of Vaseline do you use for the seals you put in the engine? I would also like to ask what glue you use to secure the screws to the engine. I bought a Loctite 243. Can I use it? Thank you for answer.

[@rmatvmc]

We used either the Bel-Ray Waterproof Grease ( www.rockymountainatvmc.com/parts/bel-ray-water-proof-grease-p ) or Maxima High Temp Waterproof Grease ( www.rockymountainatvmc.com/parts/maxima-hi-temp-waterproof-grease-p ) for the engine seals. Your Loctite 243 is a great medium strength threadlocker and will work for the majority of the bolts that call for threadlocker, except for ones that require red/high strength.

[@jorgeacosta489]

WAOOOOOO real nice

[@treywilliams5203]

When did he put the water pump in?

[@rmatvmc]

If you want to see how to remove and replace the water pump, check out our video on rebuild the water pump. Removal starts at 3:28 kzbin.info/www/bejne/a3eQm6apg7uJY8U

[@RTrevino16]

Can you guys do a step by step AC to DC conversion?

[@محمدعبدالله-ب7ش5ك]

Happy day my friend, how do I know if the Crank seal is bad or not?

[@diegojimenez4212]

You’ll know it’s bad when it starts pouring out smoke out of the right side pipe

[@martimcocco3422]

dont you need to do a leak down test?

[@otaku103]

Are those gloves resisting solvents like gasoline?

[@jlight0037]

What pistons did you use?

[@rmatvmc]

We used Vertex pistons on this rebuild.

[@hectordacgzinharocha8782]

wauuu i liked

[@alex-sanddevil5093]

Should of put it a 4mil crank and cylinders 🤩

[@edwardseaton4492]

Who sells that engine stand?? Where can i get one??

[@rmatvmc]

www.rockymountainatvmc.com/parts/motorsport-products-mx-engine-stand-p here you go!

[@otaku103]

What brand is that torque?.. May you show us that thing where you put the engine to be assambled?

[@rmatvmc]

it's a craftsman torque wrench and here is the stand we are using. www.rockymountainatvmc.com/parts/motorsport-products-mx-engine-stand-p

[@otaku103]

Thanks a lot for sharing your experiences and knowledge... God bless you

[@TECH-NOTICXs]

What’s the exact craftsman wrench ? I want one ! You guys torqued the whole engine with that one ?

[@TECH-NOTICXs]

Is this a 3/8 torque wrench or 1/4

[@MsRobiiin]

@@TECH-NOTICXs they used both

[@walterjustoguzmanramos2330]

Muchas gracias por compartir este video es muy importante para los que empezamos a trabajar con este tipo de motores Saludos desde Lima Perú Te invitamos a conocer a nuestro país un abrazo 🛵🏍️🛺🇵🇪🇵🇪🇵🇪🇵🇪arriba Perú

[@nickcollene8302]

Does the shift detent have to be in a certain direction when you put it on the shift drum??? Cause In getting real nice freeplay//// spin with all my trans and crank but I’m not getting all my gears?? Do u have an idea of what I might be able to do. Cause the shifting mechanism seems to be ok minus that! Thank you for your time!!! And any rude and smartass comments u just need to get a life 👍🏼!!! Thank you to the rest 🤓

[@claywaddell6374]

Wouldn’t use assembly lube on pistons. Rings take forever to break in like that

[@danielserrano8440]

How much $ are we talking about to rebuild the engine?

[@OGKILLa9365]

If you use Chinese crap they sell on eBay Maybe like $600. If you use high quality parts. For a crank you're looking at like $400-$450. Wiseco piston kit $200-$250, Cometic gaskets and seals $80, if your cylinders need to be rebored around $200. So like about $1000-$1200 for a stock reliable build.

[@Floridawoodsbanshee]

😳 what about now with 💤 Joe

[@cbr600rrturbo]

High 5

[@profitstyles1683]

You don't have to check for squish

[@hot_top_1686]

No leak down test for the case

[@alex-sanddevil5093]

Hot_top _1 probably not when I was building my engine 3 studs snap. Had to put all new ones and take the whole entire engine apart

[@hot_top_1686]

Sounds like you put to much pressure in the case

[@alex-sanddevil5093]

Hot_top _1 nah the previous owner on my banshee left it outside and get weathered and the studs had like side rust I should of replaced then at first but didn’t

[@dennisleach5815]

And you’ll probably think it sounds petty but it’s not petty when one of these kids blow up $12,000 they just put in a banshee cub because they missed the washer

[@dennisleach5815]

Hello all right when you were doing the clutch basket you say OK we’re putting on a Henson clutch basket blah blah blah whatever it is but this is supposed to be a do it yourself video you stick the clutch basket on and then after you’re done tell someone oh you have to put on a thick washer before that they have no clue what it looks like and then you stick the basket on and say, followed by another thick washer and a locknutif someone was going off of only visual aspect, they would’ve never put the washer behind that clutch basket

[@Bankro10mm]

Backwards seal

[@dennisleach5815]

And please don’t think I’m being a jerk I’m not being a jerk I’m just stating facts because my son and his friend build these things and I’ve been through this with them multiple times where they watch the KZbin video missed something because it wasn’t clear and $5000 went down the drain