How to reduce the noise of the Nanrobot scooter spring damping system？（Add 4 rubber rings ）

[@mrnomore]

thanx for the video! after watching it, i figure out how to do it WITHOUT taking the suspension apart! :D

[@cannacryptoo5866]

how

[@cannacryptoo5866]

cut the washer???

[@OkCricket9633]

@@cannacryptoo5866 I think by removing the screws and pulling the whole assembly out but leaving the nut caps on 🤔🤔🤔

[@simonmllerkristensen9640]

Would have been nice to hear the suspension noise before and after your fix

[@silvercrystal3]

this vid should give the best expression how it would be before... kzbin.info/www/bejne/gqjHiptmfL12n6s

[@silvercrystal3]

_Tim_ __ I wouldn't necessarily measure the difference in % of the noises between before and after but rather that smaller bumps are almost quiet now while it can still be quite noisy the bumpier it gets. Just do it. I use 8 flat seal rings in size of ~30x20x3mm purchased for 10€ at my local building store; don't want to be offensive but that price Nanrobot demands is ridiculous

[@NetworkDefense]

Would be nice if you could show how to change tire for E8 or lap a puncture tire/tube.

[@hdm6897]

i can tell thats my boy pirate working on the springs!!

[@Personne303]

@DAHODA OU: I did what you present in the video, I used not rubber pads but hard silicone. Unfortunately no improvement. Unpleasant sounds appear only when I run onto the stone as I get down it and at that moment to hear the blow. The problem is in the lower part of the damper - the head of the Allen screw on which is a rubber ring, which is insufficient. A solution could be to use a Klinger ring.

[@ionut9274]

Can you put please another site with the purchase link becouse the old one dont work anymore!

[@billhundreds8762]

Hello. what is the size of the hex Allen key used inside the shocks, please?

[@Lucas-de4vw]

o meu só tem um pá de amortecedor, esse parafuso grande que faz barulho também vc tem que colocar uma borracha nele dentro, ele vem com um anel de plástico parece ali vc coloca uma borracha não tira o anel só coloca. vc pode colocar nesse parafuso central e nas molas e calibra o pneu nunca muito duro só se vc mora onde é 100% asfalto, se for calcamento e terra ai vc deixa de um jeito que possa aperta com mão.

[@austieoutdoors9763]

my solar p1 as the same suspention as them so i will beable to do it on mine, won,t i that seems a good idea that bro thanx but does it deffo stop it

[@freedom4life123]

can this type of suspension be replaced with a better one?

[@juniorh4775]

Hello my washers to my front wheel are rusted and i cant get them off... Can you tell me how to remove them ?

[@SaltCreep45]

what size rubber rings ?

[@adamizme1]

Outer diameter: 30mm Inner diameter: 20mm 3.1mm thick

[@SaltCreep45]

@@adamizme1 Thank You

[@fotoshark]

is there any place you can buy stiffer springs? My D4+ 2.0 front suspension is always bottoming out.

[@Skylersteel]

I’m not sure what size to get for them either

[@ridealongryan]

@@Skylersteel any update pla

[@kevindarkstar]

Now would it kill the manufacturer to stick these on! 🤷🏻‍♂️

[@customboatscreensolutions5893]

I think nanrobot now implement this into the d4 / d5 suspension in manufacture. as when i purchased my d4 + i noticed this rubber ring idea had already been done.

[@Jyojin]

nanrobot doesn't do anything, they just buy hundredds of escooters from a chinese factory and just put their logos on it, this is called OEM, check halo knight t104 on aliexpress or FLJ t113, these are the ''real'' one. dont buy a nanrobot.

[@nicolapetronelli9568]

good morning, why don't you show it on the other side too? thank you

[@hdm6897]

like that song whats the name of it?

[@jesp999]

Where do you find the rubber rings?. I was only able find on line for sale rubber O-Rings that are not like yours. The ones i see for sale are rounded and not flat like yours and are inner 23.8mm x outter 30mm x 3.1mm thick. But your rubber washer rings are flat you say 20mm by 30mm 3.1. Are you sure of your siz. I search for rubber gaskests, rubber flat washers, rubber rings. but nothing comes up like what you have. do you know where to find them or what exact measurement will work best?

[@raptor2569]

Where can I get those tires?

[@Mietas2]

Any D5+ owner can tell me dimensions of the springs in from suspension pls?

[@KettlebellGunsmith]

+1. Any D5 owner please chime in?

[@radekpasecny4538]

Do you have any scooters for sale??

[@SuperGiantGeckosLLC]

Yo get a milk crate(free) for a work stand they fit perfect under the deck

[@ianrice1778]

I did this but instead of paying 25$ I took an old bike tire tube cut out circles and used them as the dampener. It works its much quieter but still get the banging sound when the springs spring back to fast. It's a nice fast and powerful scooter but if us d4+2.0 owners want a better ride we need a better scooter. I'm looking for a new scooter now. Something with 5600w motors 60v 28a and better suspension will do. Any one know good sites let me know please.

[@von9794]

that type of suspension is not easy to calibrate, you need to balance all four supension at all same level not just disassemble and assemble it, and there's a dedicated wrench for that round knot

[@angelteamnolimit624]

Music literally put me to sleep

[@MrWilliam.Stewart]

Ooh I know, sell it and buy a Yamaha, or a Honda, oh crap, they are not making e scooters yet 😐 Edit, P.S. good video.

[@jesp999]

the correct rubber gaskets are hard to find in usa in metric measurement. I only found them after searching in good old inches. The right gaskets are sized 1.25" O.D. X .98" I.D. X .13. Sometimes these are called, "rubber cap thread gaskets". That is just like what is used in this video and it fits perfect. Do not get the completely rounded things which are called rubber O rings those O rings do not really work as well since they stretch and squeeze out of the space they are trying to protect. So do not search for rings to find the right ones search for gaskets and try the mearuments above or also sometimes listed as 31/32" ID x 1-1/4" OD Black Cap Thread Gaskets for American Standard Faucets # SC0260 Brand: Brasscraft.

[@OkCricket9633]

I'm going to try and get these real soon, thanks for this info man! 👊😃

[@lukasjarka5340]

Thank YOUUUUUUUUU!

[@birobarnabas350]

Or WD-40🤣

[@Robroy11976]

Is it ok to use wd40? Will it loosen the screws?

[@elijahthebarber5419]

What size rings?