Hey Buddy I watched your 1st video and thumbs up ,, I just stumbled on this new video and thumbs up again ,, at some point I will attempt this myself ,, I'm a small time scrapper of metals and find lots of AC's , It's a good way for me to make a buck by extending the life of the air cons i find instead of sending them to their grave ,, But up here in Canada there a little freaky on freon but if I can save a buck and make a buck then F__k it i'm in ,, take care !
@JodBronson6 жыл бұрын
+Graham sargent - #1 Rule. As long you are NOT releasing Gas into the Environment, you are NOT breaking any Law! As for refilling and making Money, I am sure you can easily. Here is what I would do, if I were you. Get a good " Gauge " adapter / filler. They have them are Harbor Freight, although I don't know if they have those in Canada. I am sure you can spend extra for Shipping, since this is a Business Adventure. NOTE: If you are serious about making money.... On the Unit itself, it will tell you what type of Gas is in there. From that, you can actually buy the SAME TYPE of Gas using Ebay etc... Double check for international shipping with Seller(s). Back to the Gauge Adapter, the reason why I suggested that is..., you can " VACUUM " the Line to do the " Proper " Filling. By doing it Properly, you can have better Customer and they will send their Family / Friends to you and also, you can make Money from just doing " refills " as well. Well that is all the Tips I got for you right now. Don't be afraid to venture out...., there is a lot of Money to be made. You just have to do it! :)
@amynodine60756 жыл бұрын
Graham sargent We buy it at Canadian tire in the automotive area. Have also seen it in Walmart’s in Canada.
@rodrigocarvajal5245 жыл бұрын
I did all you said works perfect thank you buddy👌👌👍
@JodBronson5 жыл бұрын
Cool, glad it worked out! See the Updated Video and what I've learned here, it might help you further on tinkering! kzbin.info/www/bejne/h5WzmYBtfrugZ8U
@baanman5 жыл бұрын
I have an old wall ac unit that is 36 years old. It now works like brand new. I used it every year but the last couple years just was not cooling much anymore. I got inspired after watching your vids and pulled it out and did like you did. The only difference is that the unit would only take about a third of a can before it stopped taking any more, and this was on for about 30 minutes. It equalized at 50 psi and was throwing out 37 degrees steady. All the nay sayers out there, you just go out and buy your $500 AC unit, and I'll enjoy my ice cold air for $5.00. Been working nice and quiet now for several weeks, and I don't put the dial above #5 out of 10 or I would freeze. Thanks Jordan.
@JodBronson5 жыл бұрын
You are welcome! Wow, even on a 36 years old one? Wow amazing! ❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️
@DankHunt4202 жыл бұрын
Can tell me the name/model and year I just want to see what it looks like
@SheenaRea Жыл бұрын
@baanman I have a little Kenmore window unit that has worked every year for over 30 years also! It was the first AC we ever bought. They made them good back then! Anyway, I'm going to get a AC tech to "recharge" this because I'm sure it's still got life in it. Just doesn't have the COLD air I like. 🙂
@mattbaker57575 жыл бұрын
Hi Jordan! I just wanted to say thanks a MILLION for this A/C fix! My Story: a couple of years ago a purchased 2 GE window A/C's, but after several months of use they started giving off a terrible smell. The cause was that there were no drain holes in the bottom of the case for the water from the A/C's "sweating" and it collected in the bottom, about an inch deep, the fan was splashing through the water like a paddle boat, which was making the motor work harder and spraying moisture into the house! Not only that, but then the water went stagnant and a red algae started growing in the water which was the ultimate cause of the terrible odor! So, I decided to drill my own drain hole in the two A/C's, the first was successful and the problem was solved, however, during drilling of the hole in the second A/C, the drill caught me by surprise when it breached the metal case and the drill bit shot up too far and punctured one of the copper lines. A definite comic moment as I got sprayed with freon and stagnant water with algae! Not too mention I ruined the $200 A/C unit. I set it aside and bought another brand (which I made sure had a proper drain hole). But as a DIYer I planned on figuring out how to repair the A/C myself once I had the time, nothing to lose, like you Jordan, since it was broken already. I was looking for how I could refill the A/C when I stumbled across your videos which enlightened me to the existence of the line-tap. And also that I could use something other than R410a freon in it, since I didn't want to pay $100 for a big tank. So I took the A/C apart, repaired the damaged line with a copper "patch" and solder, then refilled it just as you showed. Filled to about 45-50 PSI and my A/C is now working good as new again! It cools every bit as well as the other identical unit! Thanks again! Long live DIY tinkerers!!! Matt
@mattbaker57575 жыл бұрын
So I officially call "Bullshit" on those who say you can't use R134a in a R410a window unit! Most likely they are just covering their own asses from regulations, legalities and fear of being sued, or listening to those people. And to those who say R134a will burn out a R410a compressor, I say, how the FUCK do you know?!? Have you ever tried?!? I suspect those people are just going "by the book," the same book written by manufactures and others covering their asses for regulatory and legal reasons and not wanting to be sued. Jordan's is working still after years, and mine is working fine after a week so far...if it does happen, it was a lost cause anyway, so I had nothing to lose (does ANYONE looking to fix a non-working window A/C have anything to lose?!?)...I've done a lot of fixes as a DIYer over the years that people say can't or shouldn't be done, but I did, and the fixes worked! Hurray for those of us who think for ourselves,question everything, and experiment! Think outside of the box you morons!
@JodBronson5 жыл бұрын
Wow, great story! You are welcome! YES, I think about 50 PSI would do the trick. Since I refilled this and I also did it again since I made mistakes few years ago. Happy to report, the AC Unit is working AOK still. I am cleaning it first before I make a new video, but I will update again with another video so People can see it's still working.
@JodBronson5 жыл бұрын
See the Updated Video and what I've learned here, it might help you further on tinkering! kzbin.info/www/bejne/h5WzmYBtfrugZ8U
@feddersairdude4 жыл бұрын
@@mattbaker5757 Calling professionals who took the time to study the field they work in is just down right wrong. If you yourself took any time to look into how refrigerants act based on their chemical compounds and the pressures they operate at, you would understand why you cannot simply put a different refrigerant in "because its cheaper." There is a reason why certain refrigerants are not legal to sell to individuals like yourself, simply because you have no knowledge of refrigeration whatsoever. I support DIYers and people who want to try and repair rather than replace. If you take the time to look at my channel, you will see thats something I live on, repair rather than replace. But repairs cannot be hack jobs. Your unit if it once took r410a should have a suction pressure of around 120psig, however, 134a will operate at around 40psig at that same interval (this information could be found on a P-T chart). They do not maintain even close operating pressures. You risk major damage to the compressor of the unit. Basic refrigeration knowledge, basic answer. Another example of this situation would be someone suggesting you put diesel gas in a gasoline engine....see where this is going? Feel free to contact me if you have questions regarding anything us "morons" know about OUR field. Thanks
@watcherwatchmen77853 жыл бұрын
The water splashing on the coils is actually a built in design of the A/C unit. It helps cool the coils by splashing water across them. Obviously, if you don't want it spitting water into your house you can drain the pan, but I just wanted to let you know that it's designed to do that. It works similar to the principle of how a small motor has a "slinger" that scoops up oil out of the pan and splashes it on the moving parts. It won't hurt your unit to drain the water, but it will run a little hotter.
@davebartosh53 жыл бұрын
Glad I watched this. My AC is over 5 years old and never serviced. I just wash the filter. It started making the horrid grinding sound and blows out hot air. I thought it was a lubriction issue, which may be part of the story. But when I heard your compressor, it's the same exact sound I'm getting. I'll try a kit and report back.
@chipwright61932 жыл бұрын
I have an 11 year old LG unit that I bought new. It's worked great up unit this year. Now it's starting to have some troubles. I've recharged the A/C in my cars plenty of times and was thinking of attempting it on my window unit as well. Thanks for listing the part numbers for the Bullet Piercing valves. I wasn't sure how I was going to tap into the unit. Thank you for the video!
@JodBronson2 жыл бұрын
You are welcome!
@shaunthorton70904 жыл бұрын
Jordan thanks Man ...good stuff..local electric shop was going to charge me 68 dollars a can of freo n to put in my A/C . You saved us all a shit ton of money. With the Heatwave sweeping the country here in July 2020, i think your saving some lives as well making you a 🦸♂️ superhero...up up and away 👍✌👏🤝🙏😇
@JodBronson4 жыл бұрын
You are welcome! Check Description, there are more !!!
@2bnax2 ай бұрын
THE PURPOSE OF THE LITTLE TRENCHES, WHERE YOU DRILLED THE HOLES ARE TO LEAD THE WATER TO THE CONDENSER FAN. THERE'S A RING AROUND THE FAN BLADES (SLINGER- RING) THAT PICKS UP THE WATER AND "SLINGS" IT AGAINST THE CONDENSER TO MAXIMIZE ITS COOLING EFFICIENCY- THIS HELPS THE FAN IN CONVERTING THE HIGH PRESSURE GAS TO A LIQUID AS PURPOSED. ALSO,I DIDN'T SEE YOU PURGE (OR CONTINEOUSLY FLOW) FREON THROUGH THE GAUGE LINE TO AVOID PUSHING AIR INTO THE SYSTEM. NEVERTHELESS, NOT DOING SO GIVES YOU A HIGHER "FALSE" GAUGE READING & IT INTRODUCES MOISTURE INTO THE SYSTEM, THE MOISTURE CAN CAUSE FREEZE-UPS INSIDE THE LINE CAUSING RESTRICTIONS; IT ALSO REACTS WITH THE OIL WHICH CREATES ACID & DESTROYS MOTOR WINDINGS. I ENJOYED THE VIDEO NEVERTHELESS !!!!!😇☺☺
@JodBronson2 ай бұрын
DANG, YOU TALK A LOT!!!
@2bnax2 ай бұрын
@@JodBronson SORRY! ITS USEFUL INFO ,ONLY THOUGHT YOU & YOUR LISTENERS/ READERS WOULD BE INTERESTED! I APOLIGIZE!
@JodBronsonАй бұрын
@@2bnax - HERE'S A RING AROUND THE FAN BLADES (SLINGER- RING) THAT PICKS UP THE WATER AND "SLINGS" IT AGAINST THE CONDENSER TO MAXIMIZE ITS COOLING EFFICIENCY.
@2bnaxАй бұрын
@@JodBronson I RECENTLY SENT YOU A REPLY LEADING YOU TO VIDEOS THAT EXPLAINS WHAT I POSTED IN MY REPLY ABOVE (SLINGER RING ) .... IT SEEMS YOU'VE ERASED IT, NEVERTHELESS, I HOPE YOU'VE ACCEPTED THEIR EXPLANATION - WHICH IS THE SAME AS MINE!! MAYBE YOUR READERS ARE INTERESTED
@charlesbertbibit67584 жыл бұрын
ure doin it right bro..but yup actually u have to refill the r134a till 70psi - 80psi (r22 should be more cooler)...and one more bro,the piping line got frosting its just because of the pressure of the gas u've refill and it will frost until the gas pressure refilled by 50psi and aboved..dont have to be afraid after this if u saw ur home a/c gets frosting ,my solution is check for gas pressure whether its drop to 50psi and check too if there is leaking around somewhere from ur a/c units...Keep it up!!& dont stop learning bro...its good to know some knowledge about it than know nothing,is it right??im doing this a/c things for 10 years right now,but still try to learn more and still install,repairing a/c..thumbs up for u bro...liked your videos too...👍👍🙌🙌👏👏👏🍻🍻😇
@JodBronson4 жыл бұрын
You are right on the Pressure... I was 14 years old when I first did this and inexperience, I've learn a lot since then. I document all of these since 2016 and I have the Play List here if you want to check that out. kzbin.info/aero/PLu6UVmXTZzOjYEMtytG5WMgthlA8aukaQ
@veskovesilev20192 ай бұрын
I am pretty sure the water pan at the bottom is supposed to fill with water/condensation and the fan sprinkle it on the condenser coil to keep it working strong on hot humid days. When you drill the holes it loses its cooling ability on those days. I know the coil bathing in acidic water makes it corode faster but mabe sprinkle a teaspoon of baking soda in the pan.
@JodBronson2 ай бұрын
The Fan will keep it cool enough so I would rather not take the chance on corrosion of the copper coils.
@atalakeanumonarshi1294 жыл бұрын
Some advice for you : - You can know if you have low pressure / refrigerant on your air conditioner if the refrigerant line is frosting. - I suggest to dip the refrigerant can in a water ( normal tap water or even warm water ) to heat up the can so that way all of the refrigerant will be flowing into your air conditioner. - Don't underfilled your air conditioner because the compressor will work really hard to pump your "underfilled" refrigerant. It will kill the compressor much faster. - if you have an condensation on your refrigerant line, then congratulation! You've just successfully refilled your air conditioner. Well I'm not an expert, but I know quite a lot of experience from refilling my own split system using R410-A :-D I also have some window air conditioner (5000 btu )
@felipetorres72224 жыл бұрын
Si if you have condensation in the cooling coil the refrigerant is good?
@merry-g78962 жыл бұрын
does the type refrigerant used to refill need to match type on the label?
@flackratchettheromperstomp82244 жыл бұрын
Yo, thank you so much for this video. I was going nut trying to find a video that fixed this issue that didnt require all the expensive hvac tools. Dont listen to all the haters. Thank you again.
@JodBronson4 жыл бұрын
You are welcome!
@brandoncarlsness30803 жыл бұрын
This work for you ?
@18magicMARKer5 жыл бұрын
Hey just wanna say keep making videos and repairs! especially A/C stuff...buy broken ones and fix it!? We need more videos like this. I threw out an old a/c and bought another one and now it's not as cold so I'm gonna try this. Thanks!
@JodBronson5 жыл бұрын
Everything you need is in the " Description ".
@JodBronson5 жыл бұрын
I also make bunch of other stuff too... Check out my Channel under " Video ", you might get something else useful. :)
@DJPenguino516 жыл бұрын
45 PSI on the low side is good for R134A as per the pressure / temp chart. That will give you 40 degrees at the metering device (orifice / capillary tube / expansion valve). 110 PSI is your "static" pressure before you switch on the unit. You can charge with the can inverted but ONLY in short spurts. Otherwise you can slug the compressor (not good).
@JodBronson6 жыл бұрын
+Ronnie Bradley - Here is the Video I updated after I upload this Video. I explain it in the newer updated Video here: kzbin.info/www/bejne/h5WzmYBtfrugZ8U
@nonya685 жыл бұрын
Short spurts up to where?
@rvm4574 Жыл бұрын
Can you add r134-a into split units and on top of the existing refrigerant? I installed the split unit 2 years ago and it held vacumn over night. So I don't think I have a leak but I think they just put enough freon in units. My opinion. But now it will slightly freeze up. I checked and cleaned coils and they were in great shape.
@DJPenguino51 Жыл бұрын
@@rvm4574 I would advise against it.
@TheGodfather1013 жыл бұрын
A window unit uses 410a. 134a doesn't use the same oil and operates at lower pressure. Less efficiency. Will work but will whither over time. Remember compressor are best rated for specific use.
@JodBronson3 жыл бұрын
Thanks for sharing
@rogerlimoseth47904 жыл бұрын
Thanks for the video. I've done automobiles but not a window air. Forget peoples negative or how to comments. If they were pro's. They wouldn't have searched, found and view your video.
@JodBronson4 жыл бұрын
Hahahahaha, you're right !!! ❤️❤️❤️❤️❤️❤️
@brycesstuff2 жыл бұрын
Your accent is a trip, nice vid 👍
@Thinker2-truth11 күн бұрын
The PSI in A/C is a function of ambient air temp at the time of adding R134a: 70 degrees F = 70.7 PSI 75 = 79.3 80 = 86.4 85 = 93.7 90 = 101.6 95 = 109.9 100 = 118.6
@peterhipple97322 ай бұрын
Yeah, thanks to you screwing it up, and not knowing a thing about what you are doing.lol . thanks to you I learned a lot, there's always trial and error. Thank you for the lesson. I did what you said and it worked like a charm. Thanks
@JodBronson2 ай бұрын
You are welcome!
@fustratedfisher6 жыл бұрын
If I could make a suggestion take a hvac class. You shouldn't release the refrigerant into the atmosphere. 135- and 410 is not as bad to the ozone but it will help the greenhouse gas effect. You should recover the refrigerant into a recovery tank then test the system with nitrogen to see where the leak is. Fix the leak then vacuum it to 500 microns. Then refill it with the correct amount of refrigerant that's on the data plate. Ac systems don't loose refrigerant just by age there is a leak somewhere...
@JodBronson6 жыл бұрын
+Shane Aubuchon - This Video is for Entertainment Purposes Only!
@ChrisJohnson-gq3uu5 жыл бұрын
Learn how to spell jerkoff or just shut the fuck up.
@HappySlave15 жыл бұрын
@@ChrisJohnson-gq3uu He should learn how to spell jerkoff? What pray tell will that achieve?
@jeffreymorrow49665 жыл бұрын
R134a doesn’t have to be recovered. If that was the case they would require you to have a license to buy it like r12 or r22. You don’t need an have course for that. What’s important is you retrofit the machine of going from r22 to r134. This is interesting because I might try to recharge my unit.
@jeffreymorrow49665 жыл бұрын
They freeze up when Freon is low.
@rubenrivera26005 жыл бұрын
You need to go by temperature as well as pressure 40 psi is definitely to low keep at it though you will get it ultimately you want your evaporator coil at 40-47 degrees which is above the freezing point and plenty cold enough that you won't have any issues any hvac guys out there didn't learn this overnight practice and studying makes perfect
@JodBronson4 жыл бұрын
:)
@patmorales41593 жыл бұрын
Can u add 134a freon to an air contioner thats asks for 410a ??
@alecruzcruz90472 жыл бұрын
*Great and Easy to instal **Fastly.Cool** Low noisy*
@erictheviking68324 жыл бұрын
YOU HAVE TO PURGE THE SYSTEM, THEN WITH COMPRESSOR RUNNING YOU MUST TURN THE CAN UPSIDE DOWN AND FILL TO BLUE AREA
@patmorales41593 жыл бұрын
Can u add 134a freon to a 410a air conditioning system??
@elvispressedtalot98993 жыл бұрын
This video just show cased the info you seek. he speaks it from the start.. 134a on a 410a. So im getting the same 134a refrigerant for my runined AC12000BTU. Drilled a hole on the bottom of the condenser ! but will be using epoxy with a clamp that tightens with a 8mm socket. Fk'd up when drilling extra holes. "Got LAZY and purged it unwillingly"!
@ChangeViewZАй бұрын
I just did this with my Portable Air Conditioner. Used R134A, about 2 full cans. Its blowing cold air now.
@JodBronsonАй бұрын
Awesome!
@feildcar45782 ай бұрын
Don't drill holes in it. You're wrong the fan slings the water onto the coil to get evaporative cooling that maximizes the efficiency of the air conditioner you will get lower temps with water in it. They are designed to work with water in them.
@JodBronsonАй бұрын
You forgot the fan?
@jeffreymorrow26655 жыл бұрын
I wasn’t aware of that. It seems like that would make charging your a/c a lot easier and cheaper. I didn’t know that. I’ve charged my car before and it was pretty easy.
@JodBronson5 жыл бұрын
Hi, yes it's the same principle. As long you follow the Specs on the Meter Gauge for the "Type" of Gas you are using.
@wandat465 жыл бұрын
I had one refilled and it lasted for 5 years. Well worth the money.
@JodBronson5 жыл бұрын
@@wandat46 - Nice to hear that is lasted that long! This is my 4th Season so far since I refilled it. It seems to be holding up since, but we will see.
@maltesemike91144 жыл бұрын
My mom's ac was warm n cold more warm so best sulotion I put my water hose on low spray n put on top of the AC n let the water spray on low in it cools the unit I leave on thier all day just letting water dripp into it ,of course I cleaned it..but gonna try that filling it with freon gonna buy adapter..thanks n hope my will help
@JodBronson4 жыл бұрын
Test with the Adapter first to see where your Freon at. From there, read the label to see how much you will need. Also, the label will tell you the right gas to put in too. If there is a leak, they sell leak seal too. NOTE: This is for refill only and not release any gas in the air, you will violate the EPA's rule. ;)
@palmtree55445 жыл бұрын
Read the label on the ac. It will tell you how many ounces the ac uses.
@JodBronson5 жыл бұрын
I was like 14 yo when I did this, so I didn't really know anything/much. But later this year, I went into further and I've made a Video here: kzbin.info/www/bejne/Znral4NqgqaSntU
@132900dx Жыл бұрын
This was so helpful bro. Thank U a million times. Be well I needed this.
@Poohdaddymagic4 жыл бұрын
Lol in your first video you didn't give a shit if it blew up and killed you now you say the icy lines scared you😂😂😂 Good stuff man👍🏼
@JodBronson4 жыл бұрын
LOL - Yes, but not scared of dying. LOL
@peterhipple9732 Жыл бұрын
Thanks, this video was tremendously helpful
@JodBronson Жыл бұрын
You're welcome!
@ReneStover4 жыл бұрын
When the coolant level gets low, it ices up!
@brycesstuff2 жыл бұрын
I'm a maintenance manager at a very large facility, this is correct, low refrigerant or clogged filters are what freeze up coils.
@MichaelaPsycho77132 жыл бұрын
@@brycesstuff what are the signs when it starts to get low I'm having problems with my window air conditioner
@brycesstuff2 жыл бұрын
@@MichaelaPsycho7713 im just familiar with the bigger commercial units, but I imagine its the same with smaller ones. If there is ice on your coils inside or out, I imagine you have something slowing air movement or low freon
@MichaelaPsycho77132 жыл бұрын
@@brycesstuff dang it I'm gonna take it apart and see what's wrong with it it was just making a weird noise out of no where and starting dripping water into the fans and the vents then ice was spitting out too I'm right now working on it worse comes to worse I have my neighbor to help me he works with the ac/heater company he might can help too
@MichaelaPsycho77132 жыл бұрын
@@brycesstuff I have a question while I was cleaning all the mold out I was holding it on the edge to get all the water out of the drip tray the motor the black motor right next to it there's a small tube of Cooper it was attached with some typed of black molding thing was protecting it I tired to put it back on carefully but it all crumbled I couldn't save it it was that bad like 15 pieces broke off of the molding is that important or no?? If it was what else can I use to protect the Lil tube
@oscaralarcon66955 жыл бұрын
Good video. should be at 60 to cool. Thanks we're all learning too.
@JodBronson5 жыл бұрын
I would love to go to at least 60-70, where the " Green Zone " is in the Meter. But whatever I do, it will " Neutralized " at about 50 PSIG. Here is the Update August 2018 Video explaining my findings: kzbin.info/www/bejne/h5WzmYBtfrugZ8U
@javiergonzaleztoledo5 жыл бұрын
Why does he sounds like Katt Williams the comedian
@JodBronson5 жыл бұрын
LOL, I had to look it up and never heard of him. He's making millions... I don't think he will be filling his Air Conditioners! LMFAO
@JodBronson5 жыл бұрын
@Bob Ross- Yo nigga Bob! "DAS IT!" Don't you got some painting to do my nigga? 🤣🤣🤣🤣
@d.n.36524 жыл бұрын
Javier Gonzalez a pimp named slickback
@dobycarter89964 жыл бұрын
@@JodBronson you should not be using that word...
@roynelson76132 жыл бұрын
@@JodBronson you didn't say nothing wrong you did not have an ER on the end of that so in my eyes you said nothing wrong a lot of people use that word everyday and it is accepted by a lot of the black community I have black in my family it don't bother them I don't say it but in my eyes you said nothing wrong
@jamesjacksonpolarplayАй бұрын
You the man
@joseorta99284 жыл бұрын
The line froze up cuz the system dont have freeon...and you might have a leak...on the line...
@kellykatcher75474 жыл бұрын
Ok hmm.. I have been told that you CAN NOT put R134a into a R410a system.. when did that change?
@JodBronson4 жыл бұрын
It changed when I made that video 4 years ago. LOL. Still using the SAME AIR CONDITIONER as we speak, since the refill. In the "description", there is a link to the "Original" video, you can check it out.
@kenyonmcclain5603 жыл бұрын
I'm about to do mine this afternoon using r134
@donalddunn73625 жыл бұрын
Psi should be 35 to 40 max when it's on and you got to have the ac when it on full blast and then charge the unit and then stop at 40 PSI don't go past it
@JodBronson4 жыл бұрын
No matter what I do, it won't go over. Some how it " neutralized " since the can is at 50 PSI?
@scottxp8006 жыл бұрын
The gauge your using appears to be for R22, R134a should be in the 30-40 psi range for best cooling, R22 70-80 psi, R410a 110-120 psi.(on the low pressure side, approximately, ymmv) I had a hole in my R410a unit, repaired it and found 45 psi was the best it would cool on R134a. I switched to R152a and it cools better than R134a and draws 20-30 watts less power at around the same low side pressure. R152a is also known as "Dust off" I used a side can tap. If your above 45-50 psi your going to use more electricity with less cooling due to excessive high side pressures. My 6000 btu unit now uses less than 300 watts/hr when it was using nearly 600 watts on R410a, less pressure is less load on the compressor. I get an 18°F drop in temperature from inlet to outlet.
@JodBronson6 жыл бұрын
+Scott Gaines - Thankx for the Tips :))))) - Unfortunately I don't have a Watt Meter, so I cant' measure it :(. But as far as for the Gauge, it's around 60-70 psi it said. Also, someone said I don't have to worry about " Ambient Temperatures ", since AC is different from Car AC. I did mentioned that from 30-40 psi, my Compressor was making a lot of noises. But when I got up to 50 psi or in this case 55 psi, I no longer have noises. NOTE: If you notice, no matter what I do, I wasn't able to get the psi to climb :(((. Currently, the psi in the System is around 55.
@HappySlave15 жыл бұрын
R152a is a great replacement refrigerant my only issue with it is it's a class 2 flammable gas mind you so is R32 and that has excellent cooling properties
@MrRnudalo5 жыл бұрын
you right bro ,,,i agree that,
@18magicMARKer5 жыл бұрын
why is it for entertainment? seems every educational! thanks, I never thought to recharge it!
@JodBronson5 жыл бұрын
" Entertainment Purposes " for some folks ;)
@nbarrager3 жыл бұрын
Because refrigerants are damaging to the environment and in many countries you have to be certified to handle them. I don't know why anyone can purchase small cans of 134a.
@harrycrafter182 жыл бұрын
I’m sure that unit is r-22 and this ain’t good for it at all and it won’t function properly but, it’s still interesting to know how a different refrigerant reacts ina system not designed for it. Still it would be best to have it charged wit the proper stuff
@JodBronson2 жыл бұрын
YES, if you want to do it properly, use R22 instead, that is all. This video was to prove that YOU CAN refill with R134a. By the way, smaller AC and Wine Cooler are now filled with R134a. Check it out when you are in the big box store next time, you will see it on the label itself.
@harrycrafter182 жыл бұрын
@@JodBronson Yaa that’s what I’m saying, I’m entertaining the HVAC felid currently and have a collection of small units to tinker with. And r-134 was common in cars, refrigerators, dehumidifiers, and other small appliances and still is in some cases. But is currently being phased out for some reason. Along with r-22. Even thou 22 was the absolute GOAT, it’s being replaced bc the epa can’t keep its nose outa shit it don’t belong it. But ya interesting
@JodBronson2 жыл бұрын
@@harrycrafter18 - They suppose to replace R134a with 1234yf, which is even safer. All the hypes and now it's back to R134a. :/
@skyman20023 жыл бұрын
Closed loop system shouldn't require additional refrigeration. It may be a good idea to find a leak detector, to fix leal. Could save time/frustration.
@kennethgrimes5494Ай бұрын
Jorden let's just have fun
@JodBronsonАй бұрын
YES!
@robertpolito61394 жыл бұрын
Thank you, for your help and honestly
@JodBronson4 жыл бұрын
You are welcome! If you do it right, it will last a long time. It's been 4 years, it's still cold.
@Roboticdoughbull3k5 жыл бұрын
Fix only cost 5 dollrahs thats awesome! Good tips
@JodBronson4 жыл бұрын
I no longer gets alert and don't know why :(((. Well $4.88 at Walmart!
@426superbee44 жыл бұрын
need 1 more can Damit make your mind, temp 45 to 49 is good YOUR GOOD
@mytyhwh3 жыл бұрын
find it hard to believe that unit is 134a ,thats for cars. the compressor oil probably wont let 134 mix because its meant for another oil. 410 a probably (just heard you say it) you have the right idea , there are many informative vids about ac recharging. pls where glasses (safety) refrigerant will turn eyes to a candle wax kinda stuff should it happen to spray your face. be carefull.
@JodBronson3 жыл бұрын
Believe it or not, the can itself only 40-50PSI. So regardless how I did it, I can't overflow, LOL.
@ruthshaffer39062 жыл бұрын
I done all this but my can was still full it wouldn't go into my coolant where I pierced it
@GoldSeals Жыл бұрын
I believe there is moisture in the system.Did you use a vacuum pump to pull out the moisture?This could be why its freezing up.
@JodBronson Жыл бұрын
Should've watched the video !!!
@kellyhoneyfeloncdljourney Жыл бұрын
Thank you for making this video.
@JodBronson Жыл бұрын
My pleasure!
@johnnyneston46645 жыл бұрын
Awsome work dude thanks for the video.
@JodBronson5 жыл бұрын
Thankx! It's still working. This is the 4th Season using. Here is the 2019 Update: kzbin.info/www/bejne/Znral4NqgqaSntU
@degregrio4 жыл бұрын
New at this but I have learned a lot from this video . I realize you are making this video for entertainment purposes only but I always heard never put R134a into a unit that requires R 410a . meaning in the long run R134a can do damage to the system . Since doing this have you had any problems with the unit ? I am considering doing what you did putting in R134a into a unit that requires R410A . Any input would be helpful .
@feddersairdude4 жыл бұрын
Not at all a good idea. Take it from someone who has experience in the field. You cannot just mix or replace refrigerant types, they operate at different pressures and temperatures depending on the chemical composition of the refrigerant. Putting r134a (a low pressure and temperature refrigerant) into a high temp unit such as a window unit will destroy the compressor, either by slugging or overheating.
@JodBronson4 жыл бұрын
I refill this in May-2016 and it's the 4th Season, still working. I have the 2019 Update Video here: kzbin.info/www/bejne/Znral4NqgqaSntU
@Kidd-nq4fg4 жыл бұрын
I think the unit came with R22 which is a low pressure refrigerant so idk
@007squirreldehne22 жыл бұрын
You got a lot of air pressure built up in there that you should have vacuumed down a little bit before you added but yeah you're close
@JuanBautista-su3qw2 ай бұрын
Remember that
@stanfen19664 жыл бұрын
Thanks for the info ..I'd been wondering if I could refill my window unit myself or was it time to buy a new one ..
@JodBronson4 жыл бұрын
Best thing to do is Test Leaks first. If the unit still AOK, you can do it. I refill this in May-2016 and it's the 4th Season, still working. I have the 2019 Update Video here: kzbin.info/www/bejne/Znral4NqgqaSntU
@boydoomging40915 жыл бұрын
So you recharge the ac unit that came with R22 with the new R314a and it works. I was wondering if this will work with the rooftop Rv ac system that has R22.
@JodBronson5 жыл бұрын
Hi, yes that is correct and that was 3+ years ago! It's still working today, I just updated a new video here: kzbin.info/www/bejne/Znral4NqgqaSntU
@JodBronson5 жыл бұрын
Here is the " Original " Video of it all merged together. kzbin.info/www/bejne/eWPHmWR4e8qIgtk
@JodBronson5 жыл бұрын
You can get R22 and refill it easily too, check eBay. If you want it just like the " Original " Gas R22. You can use the Port + Tap Bullet Valve and refill it. That would work also, just follow the Meter and make sure the compression is on correspond to your Gas Type.
@kylewoodward70784 жыл бұрын
@@JodBronson did you drain all the r22 out before adding the 134a?
@JodBronson4 жыл бұрын
@@kylewoodward7078 - Nope !!! It wasn't cooling, so I knew it was low.
@Jdcv994 жыл бұрын
Since theres a hole on the coils, im working on soldering it and refilling it with some freon.
@JodBronson4 жыл бұрын
I no longer gets alert from KZbin and don't know why :(((. Anyway, pressure tested it first before filling it.
@waynepierce7305 Жыл бұрын
@@JodBronsonhow did you pressure test it and did you vacuumed it out before fillingI don't have a way to vacuumed it out is all..
@JodBronson Жыл бұрын
@@waynepierce7305 - Hook up your Meter Guage and you will understand everything!
@garciaperezandres14855 жыл бұрын
Bro. That Dog is seeing a cat or something he got the that hair all up lol.
@JodBronson5 жыл бұрын
LOL, he's always like that. Once he see something he doesn't like, his back hair all raised up! LMFAO 😄😄😄😄😄😄😄😄😄
@JodBronson5 жыл бұрын
You should see him in this Video here: kzbin.info/www/bejne/eWjTpKVvoNKiZsk
@randymiller35832 жыл бұрын
Lol good job on the entertainment only 👍
@lam29884 жыл бұрын
cleaning the front and rear coils will help the air flow and help that frosting issue
@JodBronson4 жыл бұрын
Normally, yes if there is a blockage. During filling, the unit was "open".
@zyrapagal66895 жыл бұрын
Your Compressor will burnt up dude 134a is for Refrigerator r22 is for airconditioner but it was fun to watch you doing it for entertainment Purposes😄
@JodBronson5 жыл бұрын
Here.... Watch the Video I did about 3 Years ago.... All the Link in the Video of 5 - kzbin.info/www/bejne/mZrEqpmklr6HoKM
@JodBronson5 жыл бұрын
By the way, it's still working last fall... I will update another Video this year, Summer 2019.
@JodBronson5 жыл бұрын
@@chefchutardo5215 - Talking about "brain". You can't even complete a Sentence/Paragraph correctly! *Nigga, take your own advice and take some "English 101" classes!* LMFAO 😂😂😂😂😂😂😂😂😂
@BobWarnerBarn6 жыл бұрын
Thanks for your dedication.....:)
@JodBronson6 жыл бұрын
+Bob Warner - You are welcome and I hope you got something out of it!
@sh33nst3r4 жыл бұрын
So I also have a window ac unit. I just sealed the puncture hole. Everywhere I read it says only use r410a. But all I see is people using r134a. Have you had any issues? Cause if not I can finally just charge it at work. I’m a mechanic so we have a machine for r134a.
@JodBronson4 жыл бұрын
If you want to do it right and correctly, they sell R410a on eBay. You can use that and it's correct and the EPA won't get you.
@JodBronson4 жыл бұрын
Also, since you have Recovery Machines, you can do it correctly. Make sure to Vacuum the System, then Refill accordingly.
@judymayhall9096Ай бұрын
If the copper line is frosted, that means it's low.
@hgfcxz7215 жыл бұрын
Most informative video so far.
@JodBronson5 жыл бұрын
Thank you! Hope that will help further and that was my intention.
@jubone2 Жыл бұрын
Thanks, Great job...
@alfredo96843 жыл бұрын
I have a portable air conditioner brand is midea and I guess it’s low on refrigerant where do I get the 134a
@pdrnd53674 жыл бұрын
Im new to this. Do different ac window u its use different refrigerants? Or standard?
@JodBronson4 жыл бұрын
YES, depend when it's made too. There is a small label on the Unit. Look at it, it will tell you.
@dashawngary8244 жыл бұрын
@@JodBronson can i use r134a if it says r410
@JodBronson4 жыл бұрын
@@dashawngary824 - If you want to do it right and correctly. They do sell R410 and you can use that.
@edardon164 жыл бұрын
hi Jordan,i have a cuestion the fast adapter of 1/4 to 8 v1 is cheap in China is safe to order from there,if so how long it take to be here in the us i hope you know if i order from China less than $ 2 from here, any state $10 or more
@JodBronson4 жыл бұрын
Sorry not sure :(((
@jonfischer63872 жыл бұрын
If there is frost it's due to decompression removing heat and causing frost.. meaning the frost means the line that's frosting is where the leak is
@jonleone7774 жыл бұрын
Perhaps I'm missing something here, but if your refrigerant is low in a sealed system I would imagine there is a leak someplace. What good is pumping more refrigerant in if it is going to leak out again.
@JodBronson4 жыл бұрын
You are missing something for sure !!! 😂❤️😂❤️😂❤️😂❤️😂❤️😂❤️😂❤️😂❤️
@JodBronson4 жыл бұрын
NOTE: You know there are " Leaks Seal " right?
@BaMFusco4 жыл бұрын
I read somewhere that your supposed to drain the old gas whatever is left before adding new gas. Is this true? Do you know?
@JodBronson4 жыл бұрын
Right, the right way is to take everything out and the system is empty. But when I first did this, it was about to be thrown out. So I didn't really care because I started to see people filling them with R134a. When I saw that, about 4 years ago.... Small Air Conditioners and Wine Coolers were filled with R134a. That's what gave me the idea to do it. Surprisingly, this is the 3rd Season since and it's still cold. NOTE: If you want to see the original Video... It's in the link and in my channel... Just search for R134a and the oldest video.
@BaMFusco4 жыл бұрын
Jordan Bronson ok how Are you supposed to empty the old gas? Do you know how? I can’t find it anywhere. I did everything you did but the gas doesn’t seem to be coming out of the can.
@JodBronson4 жыл бұрын
@@BaMFusco - You have to bring it to a car shop that specialized in AC, they have something called " AC - Refrigerant Recovery Machine ". Also, it's against the Law to release it in the Air. NOTE: That is why I refill it, since I knew it was empty. The AC Refill Gauge should tell you how much Gas you have..., follow that Gauge.
@johnz88865 жыл бұрын
If the suction side is frosting or icing like on a outdoor unit it's low on refrigerant. And you're to only use refrigerant that is designed for the compressor!
@nonya685 жыл бұрын
John Z how do you know which to use? Is the 134a incorrect?
@johnz88865 жыл бұрын
@@nonya68 there will be a label telling what type of refrigerant and how much refrigerant the system requires
@johnz88865 жыл бұрын
@@nonya68 it is recommended if you do change refrigerants. is to pull-down a vacuum on the system to dry the lines out, and get any excess oils that are not compatible with other refrigerants that can also damage the compressor.
@bobblack3734 жыл бұрын
The person who said ~30lbs is not correct. that would be for a system designed to run off of r134a originally. this is either a r22 if it is older(uses mineral oil which can "coagulate with r134a".) or r410 which uses pve oil. it depends on temp but with r22 should be 58-72 psi depending on temp on high side you would see 240-280. r410 should be over 100. i am all for hillbilly repairs especially when all the so called pros say it's impossible.
@rogersmith7396 Жыл бұрын
134a is not compatible with R 22. The reason is 134a uses PAG oil and R22 uses mineral oil. Mineral oil is not soluble in 134a and so will not lubricate the system giving compressor burn out. All the freons have different temps and expansions and pressures and cooling efficiencies. You need to replace the system oil to use 134a. Saw a guy repair an ac system with propane. He says still working 8 years later. I'm all for DIY but results may not be to pro standards. Servile refrigerators use amonia with no electricity.
@JodBronson Жыл бұрын
Instead of writing all that crap. You should ask me why I did it? Sitting there speculating is a big sign of biii poooo laaa and skiiizooos!
@rogersmith7396 Жыл бұрын
@@JodBronson Blow it out your ass Jersey.
@fustratedfisher6 жыл бұрын
And yes 135 and 410 is a two part refrigerant and always fill in a liquid state so the can is yosidw down so the two parts go into the system in a liquid state not a vapor state
@JodBronson6 жыл бұрын
+Shane Aubuchon - This Video is for Entertainment Purposes Only!
@AgeofReason3 жыл бұрын
Imagine being mask wearing Shane.
@dustinmckenzie2078 Жыл бұрын
Holy kwap. Owkay. Lol. Awesome video tho brother!
@JodBronson Жыл бұрын
Glad you enjoyed
@WalterKnox4 жыл бұрын
when it frost up that mean it is under filled, the pressure is lower and it gets too cold, if it is overfilled the metal case on the compressor would sweat and it would not cool properly.
@JodBronson4 жыл бұрын
Listen?
@WalterKnox4 жыл бұрын
@@JodBronson i did... you were correct it was under filled and you needed to ad more, i was just explaining why it does freeze up when it is low.
@JodBronson4 жыл бұрын
@@WalterKnox - This Video was done in June 2018. I since " update " more.... See here: 2018 Update Tips - Refill follow up + Gauge Adapter tips Video: kzbin.info/www/bejne/h5WzmYBtfrugZ8U 2019 Update Video: kzbin.info/www/bejne/Znral4NqgqaSntU
@hector.c23374 жыл бұрын
Can u replace R410A for R134a ? On a window ac
@basharmo20652 ай бұрын
I have the same question what did you end up doing
@gymkhanadog6 жыл бұрын
All of your coolant pressures should be listed on the inside of the A/C unit on a tag or stamped. "This video is for entertainment purposes only..." Yet it's an instructional and tips and tricks video. This isn't entertainment, Fox News is entertainment, this is educational!
@JodBronson6 жыл бұрын
+gymkhanadog - LOL, it's because the " attacks " I get from my previous videos... I now make it as " Entertainment Purposes Only ", LOL.
@JodBronson6 жыл бұрын
+gymkhanadog - Here is what I've learned about " KZbin " in the past 2 years..., and I will share that with you. I started to make Videos and Tips of what I've learned and shared with People and maybe I too can contribute back. But it seems that I have better luck making " Free Energy Devices, Alien Abductions, Conspiracy Theories and Lies Videos ". As far as I can see and dealing with 60% of these People here on KZbin, are like visiting a " Mental Hospital ". So I follow a path and listed my Videos as " Entertainment Purposes Only " to avoid attacks! 100% of my Videos are Helpful / Useful Tips.... But dealing with these " Mental Cases ", it will be easier to say " Entertainment Purposes Only ". I hope that makes sense to you!
@BobWarnerBarn6 жыл бұрын
How does one block people for making rude remarks?
@JodBronson6 жыл бұрын
+Bob Warner - Click on the " User Name " on this Post or any Post. Once you are on their Channel, you will see " About ". Click on that and you will see " STATS ". Under " Stats ", you will see a " FLAG ". Click on that " Flag ", you will see " BLOCK USER ".
@kittybok2 жыл бұрын
Your voice is sick
@JodBronson2 жыл бұрын
*I LOVE MY VOICE! Why? Biii pooo laaa hates it! LMFAO* 😁😆🤣😂😂
@bugbugpuppy8066 жыл бұрын
Where do you get the correct fitting to put in the refrigerant?
@JodBronson6 жыл бұрын
+Bugbugpuppy - Try pausing the Video at 0:05 - Link: kzbin.info/www/bejne/sJachIqprZ18Y8k
@bugbugpuppy8066 жыл бұрын
Jordan Bronson ty
@bugbugpuppy8066 жыл бұрын
Jordan Bronson ha ha ha I’m the description ok
@JodBronson6 жыл бұрын
+Bugbugpuppy - LOL
@Ricoriccoreco Жыл бұрын
So which Val do you turn off first the can or the line as you have completed the service
so you put the bullit valve in high or low pressure pipe? going to compressure or from? thanks
@JodBronson2 жыл бұрын
LOW
@michaelbrown91986 жыл бұрын
Hey... thanks.. because I have to do the samething and the A/C repair guy wants to charge me alot
@JodBronson6 жыл бұрын
+Michael Brown - If you have the " Port ", you can do it easily and follow the " Gauge Adapter " if you have one. If not, just Charge little by little... You can always add more :)))))))))))))))))))))))))))))))))))))
@michaelgnieski41814 жыл бұрын
How much is alot?
@abelruiz4524 Жыл бұрын
Would anyone recomend a vacuum on the sistem before refill?
@JodBronson Жыл бұрын
If you want to do it correctly. YES !!!
@Oddfellowspodcast2 жыл бұрын
Like this video alot
@chrisleech15656 жыл бұрын
Hey JB! So my gauge set arrived today, and I am out working on a few old units. No choice but to use some old R22 stock and I am not happy about it. Big one, average sized and a portable model as well :-) Dogs ate the power cord and the heat discharge hose on that indoor model. So the only thing I find that looks different between manufacturers is the routing of various outer diameters of inlet tube in each of the compressors. They mostly have the same sized casing yet the capacity to cool is all over the map. Interesting .... Which is the return or low side that we are working with? Is it the line from the condensor (cold side) with what I am assuming is a pressure drop?
@JodBronson6 жыл бұрын
Look below " +Matthew Sottilare ", he asked the same question.... Read that thread!
@JodBronson6 жыл бұрын
It must be on the LOW side! Follow your Lines from the COOL / LOW side to the Condenser. Anywhere on that would be fine! :))))
@feddersairdude4 жыл бұрын
These units are NOT made to run on r134a. Different refrigerants operate at different pressures and temperatures that require many different variables to be present to work. In other words, the only refrigerant that the system should be recharged with is R22, or 410a in the new units. r134a will destroy the compressor in this system, and render it useless.
@JodBronson4 жыл бұрын
I refill this in May-2016 and it's the 4th Season, still working. I have the 2019 Update Video here: kzbin.info/www/bejne/Znral4NqgqaSntU
@Defender4012 ай бұрын
I thought that R 134 was only for cars
@williamlangley2044 Жыл бұрын
Did you draw a vacuum on the system before putting in the freon?
@JodBronson Жыл бұрын
To do it properly, yes it's best to.
@perez2877 Жыл бұрын
Can I chqr by weighting the refrigerant, some compressor have the amount,right?
@JodBronson Жыл бұрын
You need the Gauge Adaptor so it can tell you how much you have in it under compression. Weight is just to see how much, but best is by the Guage Adaptor !!!
@perez2877 Жыл бұрын
@@JodBronson oh yeah I know we can use it also the manifold gauge for see the pressure, just I asked it thank you homie
@josejpl69 Жыл бұрын
Can you buy those r134 cans on autozone for cars??? Those that come with a hose??
@JodBronson Жыл бұрын
*Everything you need is in the DESCRIPTION + PINNED POST !!!*
@maureenu30474 жыл бұрын
Where are you from? Your accent sounds like Boston maybe...
@JodBronson4 жыл бұрын
100% Boston
@livelove20304 жыл бұрын
You sound Japanese same as bruce Lee .
@JodBronson4 жыл бұрын
Bruce Lee is Chinese you idiot! 😂😂😂😂😂😂😂😂
@Saint696Anger3 жыл бұрын
Hey bud it's been awhile. With the sealant added to the 134a cans have you ever experienced clogging issues after using it with the sealant additive?
@JodBronson3 жыл бұрын
Nope. To be honest, I don't even notice the differences.
@MS-sh4xt6 жыл бұрын
Does it matter where you put the tap valve ?
@JodBronson6 жыл бұрын
+Matthew Sottilare - Yes!
@JodBronson6 жыл бұрын
+Matthew Sottilare - It must be on the LOW side! Follow your Lines from the COOL / LOW side to the Condenser. Anywhere on that would be fine! :))))
@DJPenguino516 жыл бұрын
ALWAYS charge on the "suction" side (larger line). Never, EVER on the liquid (high) side.
@JoshuaG5 жыл бұрын
I believe that you always put it in the line thats the cold one not the hot one
@nonya685 жыл бұрын
Jordan Bronson how can you tell which is which? Is the ‘covered’ line the high? Exposed low?m
@fayaapatindol32583 жыл бұрын
im injoy this video watching i know this video is but i like cause man not seruios so vrry entertement video
@jamescarroll06152 жыл бұрын
Hi, for entertainment purposes only, do you think an ac unit only needs a single can? Looking at portable ac refill.
@JodBronson2 жыл бұрын
On the AC Unit, it will tell you how much is in there. Look for the SILVER Sticker!
@jamescarroll06152 жыл бұрын
@@JodBronson sorry if this is a dumb question but how do I purge what's already in there? Thanks.
@JodBronson2 жыл бұрын
@@jamescarroll0615 - Bring it to an Auto Repair Shop, they can do that for you !!!
@earthstewardude5 жыл бұрын
Those clamp on piercing valves suck! They will eventually leak! buy a torch set, silver solder "silfos" and braze on the service ports.
@JodBronson5 жыл бұрын
It's been over 3+ years / 4th Season using it. So far it's holding. Here is the latest update: kzbin.info/www/bejne/Znral4NqgqaSntU
@brettkramer4 жыл бұрын
Please create a tutorial video and show us how to do this :)