How to remove diesel injector Mercedes OM642 engine

[@capedoryus]

Thank you my friend! I am driving a fully secured OM606 thanks to your video on injector pump seals. Your videos are the best as they don't skip the parts that are hard to film. I was considering a E320 but am having second thoughts now. We know I need to move to Toyota or Lexus but until I do seeing your videos is like seeing an old friend.

[@cliffrowell9932]

Great, concise video. I'm in the process of repairing the No:3 locking bolt on my 2.2 CDI Sprinter. I'm pleased it's not the back one, but your video gives a great insight on how to cope with the awkwardness. I used a turbo cleaning spray to melt the carbon, but probably the same stuff in a different can! Love the home made slide hammer.

[@landrover325]

I'm not a mercedes diesel mechanic. But my foolproof method of black death injector removal is to loosen the the hold down clamp a few turns, and run the engine until you hear it pop out.

[@olliperez9022]

Just "invented" similar DIY tool but wasn't sure about thread damage. Your vid gave me the certainty it won't . Thank you!

[@cedley1969]

Good call on the leak off o rings, I had no end of problems with leak off pipes coming off until I replaced them.

[@rodrigofabregas7756]

Hi, and thank you for your video. I have to do this work on my 2007 JEEP Commander CRD too, along with the oil cooler change. Looking forward to see the cleaning process of the injector tube and screw hole too. Thanks!

[@technometricglk9252]

It is a tool for cleaning the seat and redo the seat on amazon

[@technometricglk9252]

I follow you on Toyota trucks now you switch to Mercedes sprinters thanks for the video sprinters are my speciality

[@DanyStefy1]

Thank you for all your help and congratulations for such a detailed video. I can tell you are a proper passion mechanic 👍👍👍

[@TheDomin8rr]

I will have to try that carb cleaner on a sheared off glow plug that Aero-Kroil hasn't been able to budge for going on 6 months now... Those 642 injectors are a different variant than what I'm dealing with on om648 where high pressure threads are not on top or in perfect alignment with injector body but instead off-center like where return line nipple is located on that one so that slide hammer tool wouldn't work for me but I like it did the job for you! Very impressed you were able to salvage those brittle plastic clips from disintegration. Not only injector bore but also TTY clampdown bolt hole will need thorough cleaning from looks of what came out. It's a very labor intensive process which is not fully appreciated by anyone who has never had to do it so good that you're taking the time like Tasos Moschatos to make it immaculately clean before reassembly.

[@OlesyaKrivobok]

great video, i made my own injector puller after getting the tip.

[@N867LC]

great job & great video! very direct and to the point!

[@malleyland5112]

Good video thanks but would like to know what actual part has failed for this to happen and can it be prevented by some type of maintenance.

[@christopher6161]

injector seals, common problem on these

[@PCongeries]

@@christopher6161 Is also better to get more thicker than originals seals and then no problem no any more

[@christopher6161]

@@PCongeries do you have part number? VW part?

[@ManuelLopez-yl2be]

Hey man you got this thanks for the connecter process

[@christopher6161]

what about the T1N black death? same procedure ?

[@angrycatowner]

How much torque and what is the install procedure for the hold down bolts? Are there any other o-rings on those injectors?

[@bugggywhip]

Great concise video! Thanks! Where did you get the weight you used for your DIY Slide Hammer?

[@fadyramaihi1975]

Great little tool there might need to make one for my sprinter 519

[@fadyramaihi1975]

I’m in the process to get my 6 injectors out I also have a 519

[@silkroad3210]

Hi there I wanna use CeraTec for my 2013 Mercedes’ Vito 122 cdi, any recommendations welcome Does that can damage the engine intervals or it’s ready not harmful and a real inti friction…. Thanks in advance

[@gustavolucena1047]

Great Video, What kind of nut Bolt/should be used for the Puller?

[@Kuczus]

anyone know?

[@Kuczus]

M14X1,5

[@samkane6966]

o hello i have a 2008 jeep grand Cherokee with om642 engine has 11 mpg aveg that is very bad diesel milage and no check engine. i changed gas filter and air filter already. can you help please

[@stevehvac1]

What size nut is needed to attach to injector?

[@bushturkey1019]

He said its an M14 nut, pretty sure.

[@glenstamate7990]

What did you soak this injector with?

[@gazt445]

Superb video, great engineering

[@patrickgr1547]

tap tap tap ✌

[@PCongeries]

WD40 doing similar job may need more time may be

[@maxwelltakawira4240]

409 injector removal

[@peterss3868]

Tak sa to vobec nerobi. Ma sa pouzit iny vytahovak. Mal ste len stastie ze isiel lahko vytiahnut. -- That is incorrect prcedure. There is diffrent injector puller for this job, which has to be used. You had only luck that injector has been quite easily removed.

[@technometricglk9252]

But indeed did the job

[@timbodude2009]

Great video.... Best I've seen