How to remove SRS Airbag Control Module & Seat Belts on Toyota Camry 2016 -2019 | MyAirbags

[@tiomjan]

Thanks from Armenia. You are the best.

[@MyAirbags]

Art Kan, Thank you for commenting!

[@timlohmann3366]

I’ve used their service and had good luck after they reflash the module. It’s a pain getting the module out though!

[@MyAirbags]

Thank you for your business 😊

[@chunhwalim719]

I have a 2020 camry se model. The same process to get the module as this instruction?

[@MyAirbags]

Yes it is almost identical.

[@mohamedguled7923]

thankks for my teacher

[@cateyecamcook4316]

I ripped one of my airbag wires to my backseat, would they go off if I spliced them back together, and would the code go away if I cleared them with a code reader?

[@MyAirbags]

First, disconnect the battery, and then you can you can solder or splice them back together. For Toyota, you should not need a code reader to clear the code. It will clear itself after the problem is solved. However, if the vehicle was in an accident, then it would have crash data and need to be sent to myairbags.com to clear crash data/crash history.

[@cateyecamcook4316]

@@MyAirbags no crash or anything, just ripped it while putting seat covers on, thanks,

[@sukman10.19]

I really appreciate it thanks you are the best

[@MyAirbags]

Kolya, Thank you for commenting!

[@dancewithml]

I just got this message in my dash this morning. Ran a scan with my scanner and it gave my nothing, then later the message came back. Any thoughts on what could cause that?

[@MyAirbags]

You must use a scanner that reads airbag codes. Then scan SRs airbag system for codes. If light just came on one day, then issue is most likely with a bad connection somewhere. If vehicle was in an accident then airbag module needs to be reset and seat belt need to be rebuilt if they are not working correctly.

[@yeuvocon2011]

I have 2017 Toyota camry, I do exactly like the guy and I don't see the airbag module inside like this car, do you have any idea where is it located

[@MyAirbags]

Its in a different location in your 2017 model? If thats the case, then it should be more towards the back of the center/middle console. More towards where the driver would rest his/her right elbow. Directly underneath, on the floor. If you see it, would you reply back on here and let us know please?

[@samuelyusuf2754]

Will this video also work for Toyota camry 2012?

[@MyAirbags]

Hi Samuel, the 2019 is different than the 2012, but, there are some similarities. Especially when you actually get to the module. Seat belts as well.

[@MichaelKing-tw3qw]

Thanks for showing us how to disconnect battery 😂

[@daveinak4639]

Is the 2019 camry the same as the 18?

[@MyAirbags]

David, As for the interior / console setup, the 2018 and 2019 are the same. The airbag module is definitely can differ from 2018 and 2019. For many cars, even the SAME year can have different modules. It depends on the different safety options it has and whats it programmed to/for. If you're trying to buy another module, its best to find one that has the same exact part number as your original. Or better yet, you can get your original reset and not have to worry about it not being a perfect fit and programming to your car. Reset service here: www.myairbags.com/product-category/repair-return/airbag-module-reset/

[@rangala5925]

Hello Thanks for your information. Can you show me when is location of front Clarence sensor module? Thanks

[@MyAirbags]

What module location?

[@rangala5925]

@@MyAirbags the code of module 89340A

[@frnsyskwrod4817]

Hi guys!!! can I drive my car without that module??? for a while waiting back for you to fix it?

[@MyAirbags]

HI, we have an answer for this on our help center: myairbags.zendesk.com/hc/en-us/articles/115012408547-Can-I-drive-my-car-truck-while-the-airbag-module-is-removed-

[@jesussamayoa7605]

How much it cost to reset them?

[@MyAirbags]

Reset price is based on vehicle year make and model. Price starts at $59.99, here is the link for more info: www.myairbags.com/product/airbag-module-reset-3/

[@jesussamayoa7605]

@@MyAirbags thanks

[@GanchoTodorov]

Hi, after an unsuccessful reset of SRS module (89170-06641) of my 2018 Camry, I have many malfunction messages on screen. After check with Techstream Diagnostic tool I realized that there are many DTC for communication faults - U0123, U0124,U0125, U0151. I checked all the cables, connections, fuses - everything looks good. On the connector have voltage. CAN BUS check shows there is no communication with airbag system only. I think my SRS module is dead. Is this possible?

[@MyAirbags]

Reset will only clear crash data and crash codes, crash history. The airbag module should only be reset after vehicle was in an accident. The airbag control module can be bad and may need to be changed. Check the plug to make sure the pins are not bent, that can cause communication issues as well.

[@popas968]

I have many malfunctions on my 2018 Camry! How to fix this?

[@BeezyKing99]

Can you demonstrate how to recalibrate the OCS? (Occupation Classification System) as I have a Toyota Corolla ‘14 which has been rear ended with zero deployment of airbags... I have researched for hours on end with no avail as to how I can recalibrate it with a scan tool. There are tons of videos out there on how to reset the light, but I don’t want to reset the light, I want to recalibrate the OCS without paying out the rear for a dealer job.

[@MyAirbags]

Beezy King, Are you getting either one of these two codes: B1795-occupant classification ecu malfuntion - OR - B1797-calibration abnormal If not, which codes are showing up?

[@BeezyKing99]

The OCS code... it’s showing a malfunction however all wires are fine... which is what I don’t understand.

[@MyAirbags]

If you have the actual code, that usually gives us a better sense of direction for troubleshooting... You can always try to run a Zero point calibration procedure on a scanner. The actual procedure steps differ from the scan tool being used.

[@BeezyKing99]

My Airbags lets say I’m picking up the innova 3160 SRS/ABS scanner... I had the code on a paper somewhere but still looking for it.

[@BeezyKing99]

My Airbags B1650 is the error code.. do I need to bring the car to a dealer?

[@daveinak4639]

What is the little tool called that you use to pry the clips? I'd like to get one.

[@MyAirbags]

Hi David, thanks for the question. Are your referring to silver pen-like tool seen on airbag module plug clips?

[@rupeshpatel2958]

Hi

[@MyAirbags]

I am happy that it helped you!

[@Poninas87]

Yo trabajo directamente de la fabrica en mexico yo programo y reprogramo esos modulos lineas ab4,ab6,ab7 modelos 2060,2090,5940,3072,3540,3550 y mas modelos en generacion 2.5,2.7,3.0,3.5 etc se realizan manual checker se reflashea son muchos procesos

[@johnboysautobody4214]

I need airbag module services.. Can you help me?

[@MyAirbags]

JohnBoys AutoBody, Yes we can help. Our contact info is here on our site: www.myairbags.com/product-category/repair-return/airbag-module-reset/

[@CV81823]

Hi. I have a 2012 camry le 4 cylinder. Bought the car from offer up. I'm not sure if the previous owner had caused the car to be on a minor crash. Airbag light always turns on and stays on. Ran a ob2 pro scanner. It doesn't detect any airbag codes. Could the module be the problem?

[@MyAirbags]

For Toyota vehicles most of the time after vehicle was in an accident then there will not be any codes in the airbag control module, this means the airbag control module has crash data/crash history stored and the airbag control module needs to be replaced or sent to myairbags.com to be reset.

[@CV81823]

@@MyAirbags ok. Would the front impact sensor on a 2012 camry trigger the airbag light with codes or no codes?

[@MyAirbags]

@@CV81823 yes the light will be on with codes for impact sensor

[@CV81823]

@@MyAirbags ok. I ran my ob2 computer and there's no airbag light codes. I'm assuming I only have to send you guys my passenger module to get it reset

[@MyAirbags]

@@CV81823 only send us airbag control module if vehicle was in an accident. That is all we reset. If your vehicle was not in an accident then the airbag module reset will not be beneficial for you, because we only clear crash data, crash history. For Toyota vehicles if vehicle was in an accident and there is no codes, then that is crash data/crash history

[@VeganAtmosphere]

SRS light please help

[@MyAirbags]

Problem with your seat belt pretensioner. It could be a bad connection or a bad seat belt. Check the wiring connection if it is good then seat belt pretensioner will need to be replaced or we can rebuild it, see this link for seat belt repair: www.myairbags.com/product/seat-belt-repair-1-stage/

[@lynnesaija]

Is the Module in the same place on a 1993 Toyota Camary?

[@MyAirbags]

Yes, it's under the radio on the floor.

[@MichaelBroyan]

Hi, my module was reset (not by you, just asking for help), and now the clock on head unit is stuck in one time position and all tuning buttons for clock are gone from the menu. It's Camry V70 with Fujiten headunit. Can you helpe or hint what it may be?

[@MyAirbags]

Hi Michael, It does seem like that would be linked to the airbag computer. If you find out the cause of the problem, would you let us know what the end result was. Your advice and helpful contribution would other people here in the community that may be having a similar issue. Thanks for your question!

[@VeganAtmosphere]

I have b1926

[@MyAirbags]

Problem with your seat belt pretensioner. It could be a bad connection or a bad seat belt. Check the wiring connection if it is good then seat belt pretensioner will need to be replaced or we can rebuild it, see this link for seat belt repair: www.myairbags.com/product/seat-belt-repair-1-stage/

[@boxcustom]

After air bag module reset from you it still shows b1790. Airbag sensor assembly ecu communication circuit malfunction.

[@MyAirbags]

Was your vehicle in an accident?

[@mshabeer5172]

Not module programming

[@MyAirbags]

M Shabeer, please clarify your question?

[@krausedj]

Airbag control modules are literally not designed to be reset, once they fire, they are supposed to be replaced.

[@MyAirbags]

Daniel, this is a really good point! Modules are computers that store codes in them. After an accident, the modules will store codes inside referring to the accident. The dealership will tell you they can't be cleared. They will tell you just to replace them with a brand new one. If you're rebuilding car, it is entirely possible to reset the collision / hard codes right out of the original module and it will work just as designed. This saves the re-builder hundreds $ in most cases. We are able to provide this service here: www.myairbags.com/

[@DJSurge951]

you are a goat

[@MyAirbags]

Thank you!